search

Koenkk / zigbee2mqtt

Zigbee 🐝 to MQTT bridge 🌉, get rid of your proprietary Zigbee bridges 🔨
https://www.zigbee2mqtt.io
GNU General Public License v3.0
11.3k stars 1.61k forks source link

Aqara Motion Sensor P1 - cannot connect #17696

Closed przemekgithub closed 11 months ago

przemekgithub commented 1 year ago

What happened?

I have two P1 sensors, and with one of them I started to have issues - it didnt recognized movement anymore. So I resetted both of them and forced to remove from zigbee2mqtt. Now I cant completely connect them. Nothing shows in logs. Upgraded firmware on zigbee stick to newest, zigbee2mqtt is newest. Device: https://www.zigbee2mqtt.io/devices/RTCGQ14LM.html Zigbee2MQTT version [1.30.4] Coordinator type zStack3x0 Coordinator revision 20221226

What did you expect to happen?

It would be possible to connect it again

How to reproduce it (minimal and precise)

Reset device and force removal

Zigbee2MQTT version

1.30.4

Adapter firmware version

20221226

Adapter

zStack3x0

Debug log

No response

lux73 commented 1 year ago

try to restart z2m AFTER force remove the Device

check the Battery - just Aqara Devices need healthy Battery to connect the Network (anything under 3V are bad)

try to update your Coordinator - latest Dev-Firmware 20230507 works really really good!

github-actions[bot] commented 12 months ago

This issue is stale because it has been open 30 days with no activity. Remove stale label or comment or this will be closed in 7 days

Programmierus commented 6 months ago

For those who will still search it on Google. I don't know if it was my system specific but it helped me to pair multiple sensors:

  1. Disable z2m network join
  2. Wait a few minutes
  3. VERY IMPORTANT - Put P1 to pairing mode by holding it's button for more than 5 seconds (z2m joining disabled!)
  4. Enable z2m network join
djkemp commented 6 months ago

I recently got 3 of these after watching all the rave reviews and tried so many times to pair them.

The closest I got was a failed pairing which required me to force remove, and then neither of the 2 I opened were recognised again after that. I must have tried without exaggeration about 100 times to get them to pair, restarting Z2M, putting them in pairing mode before enabling network join etc.

Updating HA, Z2M and the dongle firmware to no avail so had to return them in the end. Was annoyed because I have some Aqara light switches, wireless buttons and a temp sensor that are all great.

It could have been the battery but these were brand new, and that battery compartment is ridiculously difficult to open. Now on the search for an alternative.

jjanderson commented 6 months ago

after about 5 years of working flawlessly in deconz, I recently started to migrate al my gear over to Z2M. These particular sensors are however quite problematic with Z2M., not sure what the issue is. However, I recently started replacing all the aquara stuff with these - they come up as Tuya in Z2M and I find they work really well, they are also really really really cheap (like £3 a pop cheap)

TeHashX commented 5 months ago

I successsfully paired a new Aqara Motion P1 and updated firmware from v0.0.0_0006 to v0.0.0_0010, then I removed device from Z2M. After trying to rejoin network it didn't work, tried more than 20 times, restarted Z2M addon, restarted Home Assistant, even rebooted the server, still no success and nothing in the debug log. As a last resort I enabled "Permit Join" (Philips Hue Bulb) only and the device was recognised instantly.

If someone else facing the same issue, try to select another router device, not (All) or (Coordinator)!

ankitmehtame commented 3 months ago

For those who will still search it on Google. I don't know if it was my system specific but it helped me to pair multiple sensors:

  1. Disable z2m network join
  2. Wait a few minutes
  3. VERY IMPORTANT - Put P1 to pairing mode by holding it's button for more than 5 seconds (z2m joining disabled!)
  4. Enable z2m network join

I tried everything, but no avail. This really worked. Need to wait some time even after disabling join from Z2M. Thanks a bunch!

john-nosky commented 2 months ago

I also had a lot of trouble getting mine to connect after hours of attempts. I have a bunch of 3rd Reality electrical outlets and it might have been them causing the issue. Once I only allowed my coordinator to permit connecting did the Aqara finally join the network.

irlstu commented 4 weeks ago

+1 here. Made dozens of attempts to pair but nothing happened. It worked when I put the P1 into pairing mode first then put z2m into 'permit join' mode. Joined instantly. Thanks for the tips :)