search

Lijmer / arduino-tvout

Automatically exported from code.google.com/p/arduino-tvout
0 stars 0 forks source link

Getting signal but black screen #79

Open GoogleCodeExporter opened 8 years ago

GoogleCodeExporter commented 8 years ago 
What steps will reproduce the problem?
1. Use latest tvout library 
2. 470 ohm and 1k ohm resistor
3. Plug into tv

What is the expected output? What do you see instead?
There should be an image on the screen.  I am getting a signal because each tv 
goes from no signa; to a black screen.  I have used two arduino uno rev 3 
boards and one atmega 2560 with same result.  I tried with both pal and ntsc.  
On one screen I am able to see a single pixel line faintly with ntsc.

What version of the product are you using? On what operating system?
Arduino rev 3, atmega 2560.  Arduino 1.0.5.  Mac OS X Maverics 10.9.1

Please provide any additional information below.

Original issue reported on code.google.com by he...@evanstoddard.me on 27 Jan 2014 at 9:15

GoogleCodeExporter commented 8 years ago 
WB7ODYFred here, This TVOutBeta1 code worked great on my OSEPP Arduino UNO 
board a year ago.  Even the Audio output fed into the TV audio input ( RED RCA 
jack, or White RCA Jack). 

Visit this instructable and re-check your wiring setup to the atmega 2560.  
Maybe different pin numbers are used for the atmega 2560 board than the UNO 
Board.   Realize the difference between Arduino PCB Board PIN numbering and the 
actual microcontroller pin numbering.

from http://code.google.com/p/arduino-tvout  Arduino PCB Board Pin Numbers
                Sync    Video   Audio
m1280,m2560 B 5 A 7 B 4
UNO             7       9       11

http://www.instructables.com/id/TV-Out-with-Arduino/?ALLSTEPS
I give the source code for my test pattern that you can test for yourself on 
your atmega 2560.  You might have to change the SYNC, VIDEO, AUDIO Port Output 
pin numbers in the TVOut code section to match your atmega controller pin 
numbers.

Wish you well on finishing this project.  Comment back here, both with 
questions and what you did to make it work.   Best wishes,   Fred

Original comment by WB7ODYF...@yahoo.com on 29 Jan 2014 at 5:36

GoogleCodeExporter commented 8 years ago 
These resistors Sync 470 ohms &  Video 1000 ohms worked with 5V power supplied 
to the Arduino UNO Rev. 3.   Is the clock frequency 16 Mhz on your board?

If you are running the Arduino with 3.3V power, then change the resistors to a 
different value Sync 270 ohms and Video 680 ohms.
See this web page of information that was also given above in Issue 66.
http://www.incrediblediy.com/2013/03/connecting-arduino-pro-33v8mhz-to-tv.html

Original comment by WB7ODYF...@yahoo.com on 29 Jan 2014 at 6:04

GoogleCodeExporter commented 8 years ago 
I do know the pin differences and I know that both operate at 5v and I'm using 
the correct resistor values.  I will check on the clock frequency.  That may be 
my problem.

Original comment by he...@evanstoddard.me on 3 Feb 2014 at 5:00

GoogleCodeExporter commented 8 years ago 
So the arduinos are all 5v at 16mhz and everything seems correct but still no 
video.

Original comment by evanrsto...@gmail.com on 3 Feb 2014 at 5:39

GoogleCodeExporter commented 8 years ago 
Im having a similar problem with my arduino. For some reason on the RCA hookup 
it wont work with the resistors although if i just hook it directly into the 
board without resistors it works any idea why the resistors wont work with the 
RCA setup.

Original comment by dariuspe...@gmail.com on 4 Dec 2014 at 9:50