Closed cn0xroot closed 6 years ago
Raspberry Pi restart or yateBTS? Raspberry pi connected to adequate power supply? If raspberry pi is restarting after plugging in the card, you may have a bad bladeRF
From: cn0xroot [mailto:notifications@github.com] Sent: Sunday, November 19, 2017 11:04 PM To: MBRO95/PortableCellNetwork PortableCellNetwork@noreply.github.com Cc: Subscribed subscribed@noreply.github.com Subject: [MBRO95/PortableCellNetwork] Which version of BladeRF firmware are you used? (#4)
Thanks your nice project. when i use it with bladerf ver.1.9 or 2.0 firmware ,Signal interruption and restart. maybe BladeRF Firmware version problem?or bladeRF Temperature is too high?
— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHubhttps://github.com/MBRO95/PortableCellNetwork/issues/4, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AIo9w9DOOLTAFMpR_eVmWiN1SkKGZ5eXks5s4PoigaJpZM4Qjt0I.
yateBTS restart
Okay, so yate spits outs some ugly stuff to the console while it’s running in normal operation. The restarts are alarming though. I can’t recall what BladeRF firmware we flashed and I didn’t write it in my notes unfortunately. I believe we were initially on 1.6 and then I flashed whatever was newest circa April ‘17. Have you tried with one of the prebuilt images? If yes, have you tried with fresh install and then running the install script?
Best,
Matthew May
From: cn0xroot notifications@github.com Sent: Monday, November 20, 2017 9:20:38 PM To: MBRO95/PortableCellNetwork Cc: MBRO95; Comment Subject: Re: [MBRO95/PortableCellNetwork] Which version of BladeRF firmware are you used? (#4)
yateBTS restart
— You are receiving this because you commented. Reply to this email directly, view it on GitHubhttps://github.com/MBRO95/PortableCellNetwork/issues/4#issuecomment-345895542, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AIo9w51kHLevHyuHaHM1cizVBdPgKW4gks5s4jN1gaJpZM4Qjt0I.
I used 4.13.2017 Build images.should i rebuild yatebts with the install script?
I would try to install Linux fresh, download the script, permission and run it
Best,
Matthew May
From: cn0xroot notifications@github.com Sent: Monday, November 20, 2017 9:31:12 PM To: MBRO95/PortableCellNetwork Cc: MBRO95; Comment Subject: Re: [MBRO95/PortableCellNetwork] Which version of BladeRF firmware are you used? (#4)
I used 4.13.2017 Build images.should i rebuild yatebts with the install script?
— You are receiving this because you commented. Reply to this email directly, view it on GitHubhttps://github.com/MBRO95/PortableCellNetwork/issues/4#issuecomment-345897293, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AIo9w9z2UxEy5fRXADNR0NAgkogpfIG0ks5s4jXvgaJpZM4Qjt0I.
Thanks for your help.
Have a nice day!
You too! No problem.
Best,
Matthew May
From: cn0xroot notifications@github.com Sent: Monday, November 20, 2017 9:38:21 PM To: MBRO95/PortableCellNetwork Cc: MBRO95; Comment Subject: Re: [MBRO95/PortableCellNetwork] Which version of BladeRF firmware are you used? (#4)
Thanks for your help.
Have a nice day!
— You are receiving this because you commented. Reply to this email directly, view it on GitHubhttps://github.com/MBRO95/PortableCellNetwork/issues/4#issuecomment-345898388, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AIo9w2v-qen83TPHgkHcBWa8AYd4AdbEks5s4jeZgaJpZM4Qjt0I.
Thanks your nice project. when i use it with bladerf ver.1.9 or 2.0 firmware ,Signal interruption and restart. maybe BladeRF Firmware version problem?or bladeRF Temperature is too high?