search

MCUdude / MiniCore

Arduino hardware package for ATmega8, ATmega48, ATmega88, ATmega168, ATmega328 and ATmega328PB
Other
979 stars 241 forks source link

I can't boot the Bootloader for ATmega8-AU TQFP-32 #77

Closed VoLinhTruc closed 5 years ago

VoLinhTruc commented 5 years ago

I've successfully boot the bootloader for ATmega8-A DIP-28 But with the same wiring, I can't boot the bootloader for ATmega8-AU TQFP-32 And I get this error:

` avrdude: Version 6.3-20171130 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch

     System wide configuration file is "C:\Users\Bico\AppData\Local\Arduino15\packages\MiniCore\hardware\avr\2.0.1/avrdude.conf"

     Using Port                    : COM3
     Using Programmer              : arduino
     Overriding Baud Rate          : 19200
     AVR Part                      : ATmega8
     Chip Erase delay              : 10000 us
     PAGEL                         : PD7
     BS2                           : PC2
     RESET disposition             : dedicated
     RETRY pulse                   : SCK
     serial program mode           : yes
     parallel program mode         : yes
     Timeout                       : 200
     StabDelay                     : 100
     CmdexeDelay                   : 25
     SyncLoops                     : 32
     ByteDelay                     : 0
     PollIndex                     : 3
     PollValue                     : 0x53
     Memory Detail                 :

                              Block Poll               Page                       Polled
       Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
       ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
       eeprom         4    20   128    0 no        512    4      0  9000  9000 0xff 0xff
       flash         33    10    64    0 yes      8192   64    128  4500  4500 0xff 0x00
       lfuse          0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
       hfuse          0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
       efuse          0     0     0    0 no          0    0      0     0     0 0x00 0x00
       lock           0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
       calibration    0     0     0    0 no          4    0      0     0     0 0x00 0x00
       signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

     Programmer Type : Arduino
     Description     : Arduino
     Hardware Version: 2
     Firmware Version: 1.18
     Topcard         : Unknown
     Vtarget         : 0.0 V
     Varef           : 0.0 V
     Oscillator      : Off
     SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 (retrying)

Error while burning bootloader. Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check.

avrdude done. Thank you.

MCUdude commented 5 years ago

This is purely a hardware problem, and not related to MiniCoreat all. I suggest you ask for hardware related issues like this in the Avrdude, stk500, Bootloader issues section on the Arduino forum.