ellensp
commented
2 years ago Config files are not updated correctly for current bugfix. In particular there are changes with SET_PROGRESS_MANUALLY that when you don't update the configs cause these symptoms. Here are all the changes I made to set it back to defaults where the option was not enabled and all other changes required
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 8cc1239bbe..2c29c76779 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -141,6 +141,8 @@
// Choose your own or use a service like https://www.uuidgenerator.net/version4
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+// @section stepper drivers
+
/**
* Stepper Drivers
*
@@ -240,6 +242,8 @@
//#define SINGLENOZZLE_STANDBY_FAN
#endif
+// @section multi-material
+
/**
* Multi-Material Unit
* Set to one of these predefined models:
@@ -252,6 +256,7 @@
*
* Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
* See additional options in Configuration_adv.h.
+ * :["PRUSA_MMU1", "PRUSA_MMU2", "PRUSA_MMU2S", "EXTENDABLE_EMU_MMU2", "EXTENDABLE_EMU_MMU2S"]
*/
//#define MMU_MODEL PRUSA_MMU2
@@ -403,7 +408,7 @@
//#define MKS_PWC // Using the MKS PWC add-on
//#define PS_OFF_CONFIRM // Confirm dialog when power off
//#define PS_OFF_SOUND // Beep 1s when power off
- #define PSU_ACTIVE_STATE HIGH // Set 'LOW' for ATX, 'HIGH' for X-Box
+ #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box
//#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
//#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power
@@ -491,7 +496,7 @@
* 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
* 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
- * 66 : 4.7MΩ Dyze Design High Temperature Thermistor
+ * 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
* 67 : 500kΩ SliceEngineering 450°C Thermistor
* 68 : PT100 amplifier board from Dyze Design
* 70 : 100kΩ bq Hephestos 2
@@ -513,6 +518,7 @@
* 110 : Pt100 with 1kΩ pullup (atypical)
* 147 : Pt100 with 4.7kΩ pullup
* 1010 : Pt1000 with 1kΩ pullup (atypical)
+ * 1022 : Pt1000 with 2.2kΩ pullup
* 1047 : Pt1000 with 4.7kΩ pullup (E3D)
* 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
* NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
@@ -558,6 +564,10 @@
#define MAX31865_SENSOR_OHMS_1 100
#define MAX31865_CALIBRATION_OHMS_1 430
#endif
+#if TEMP_SENSOR_IS_MAX_TC(2)
+ #define MAX31865_SENSOR_OHMS_2 100
+ #define MAX31865_CALIBRATION_OHMS_2 430
+#endif
#if HAS_E_TEMP_SENSOR
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
@@ -722,6 +732,7 @@
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
* heater. If your configuration is significantly different than this and you don't understand
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ * @section bed temp
*/
#define PIDTEMPBED
@@ -1629,7 +1640,7 @@
#define DISABLE_E false // Disable the extruder when not stepping
#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
-// @section machine
+// @section motion
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
#define INVERT_X_DIR true
@@ -1766,7 +1777,7 @@
*/
//#define FILAMENT_RUNOUT_SENSOR
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
- #define FIL_RUNOUT_ENABLED_DEFAULT false // Enable the sensor on startup. Override with M412 followed by M500.
+ #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
@@ -1816,7 +1827,7 @@
// After a runout is detected, continue printing this length of filament
// before executing the runout script. Useful for a sensor at the end of
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
- //#define FILAMENT_RUNOUT_DISTANCE_MM 3
+ //#define FILAMENT_RUNOUT_DISTANCE_MM 25
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
// Enable this option to use an encoder disc that toggles the runout pin
@@ -1942,7 +1953,7 @@
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
// Set the number of grid points per dimension.
- #define GRID_MAX_POINTS_X 7
+ #define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Probe along the Y axis, advancing X after each column
@@ -2130,9 +2141,8 @@
#define XY_DIAG_BD 282.8427124746
#define XY_SIDE_AD 200
- // Or, set the default skew factors directly here
- // to override the above measurements:
- #define XY_SKEW_FACTOR 0.0
+ // Or, set the XY skew factor directly:
+ //#define XY_SKEW_FACTOR 0.0
//#define SKEW_CORRECTION_FOR_Z
#if ENABLED(SKEW_CORRECTION_FOR_Z)
@@ -2141,8 +2151,10 @@
#define YZ_DIAG_AC 282.8427124746
#define YZ_DIAG_BD 282.8427124746
#define YZ_SIDE_AD 200
- #define XZ_SKEW_FACTOR 0.0
- #define YZ_SKEW_FACTOR 0.0
+
+ // Or, set the Z skew factors directly:
+ //#define XZ_SKEW_FACTOR 0.0
+ //#define YZ_SKEW_FACTOR 0.0
#endif
// Enable this option for M852 to set skew at runtime
@@ -2200,7 +2212,7 @@
// @section temperature
//
-// Preheat Constants - Up to 6 are supported without changes
+// Preheat Constants - Up to 10 are supported without changes
//
#define PREHEAT_1_LABEL "PLA"
#define PREHEAT_1_TEMP_HOTEND 200
@@ -2358,7 +2370,7 @@
*/
//#define PRINTCOUNTER
#if ENABLED(PRINTCOUNTER)
- #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
+ #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print.
#endif
// @section security
@@ -2984,6 +2996,7 @@
//#define ANYCUBIC_LCD_CHIRON
#if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
//#define ANYCUBIC_LCD_DEBUG
+ //#define ANYCUBIC_LCD_GCODE_EXT // Add ".gcode" to menu entries for DGUS clone compatibility
#endif
//
@@ -3052,7 +3065,7 @@
//#define MKS_ROBIN_TFT_V1_1R
//
-// 480x320, 3.5", FSMC Stock Display from TronxXY
+// 480x320, 3.5", FSMC Stock Display from Tronxy
//
//#define TFT_TRONXY_X5SA
@@ -3151,10 +3164,11 @@
//
//#define TOUCH_SCREEN
#if ENABLED(TOUCH_SCREEN)
- #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
- #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+ #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
+ #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
- //#define TOUCH_IDLE_SLEEP 300 // (s) Turn off the TFT backlight if set (5mn)
+ //#define DISABLE_ENCODER // Disable the click encoder, if any
+ //#define TOUCH_IDLE_SLEEP_MINS 5 // (minutes) Display Sleep after a period of inactivity. Set with M255 S.
#define TOUCH_SCREEN_CALIBRATION
@@ -3245,16 +3259,19 @@
* luminance values can be set from 0 to 255.
* For NeoPixel LED an overall brightness parameter is also available.
*
- * *** CAUTION ***
+ * === CAUTION ===
* LED Strips require a MOSFET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
+ *
* NOTE: A separate 5V power supply is required! The NeoPixel LED needs
* more current than the Arduino 5V linear regulator can produce.
- * *** CAUTION ***
*
- * LED Type. Enable only one of the following two options.
+ * Requires PWM frequency between 50 <> 100Hz (Check HAL or variant)
+ * Use FAST_PWM_FAN, if possible, to reduce fan noise.
*/
+
+// LED Type. Enable only one of the following two options:
//#define RGB_LED
//#define RGBW_LED
@@ -3263,6 +3280,10 @@
//#define RGB_LED_G_PIN 43
//#define RGB_LED_B_PIN 35
//#define RGB_LED_W_PIN -1
+ //#define RGB_STARTUP_TEST // For PWM pins, fade between all colors
+ #if ENABLED(RGB_STARTUP_TEST)
+ #define RGB_STARTUP_TEST_INNER_MS 10 // (ms) Reduce or increase fading speed
+ #endif
#endif
// Support for Adafruit NeoPixel LED driver
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index fff93d26a2..c68315d46a 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1,6 +1,6 @@
/**
* Marlin 3D Printer Firmware
- * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -175,6 +175,7 @@
//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus.
//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board.
//#define MAX31865_SENSOR_WIRES_1 2
+//#define MAX31865_SENSOR_WIRES_2 2
//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz.
//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors.
@@ -185,6 +186,7 @@
//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings.
//#define MAX31865_WIRE_OHMS_1 0.0f
+//#define MAX31865_WIRE_OHMS_2 0.0f
/**
* Hephestos 2 24V heated bed upgrade kit.
@@ -481,18 +483,22 @@
// before a min_temp_error is triggered. (Shouldn't be more than 10.)
//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
-// The number of milliseconds a hotend will preheat before starting to check
-// the temperature. This value should NOT be set to the time it takes the
-// hot end to reach the target temperature, but the time it takes to reach
-// the minimum temperature your thermistor can read. The lower the better/safer.
-// This shouldn't need to be more than 30 seconds (30000)
+/**
+ * The number of milliseconds a hotend will preheat before starting to check
+ * the temperature. This value should NOT be set to the time it takes the
+ * hot end to reach the target temperature, but the time it takes to reach
+ * the minimum temperature your thermistor can read. The lower the better/safer.
+ * This shouldn't need to be more than 30 seconds (30000)
+ */
//#define MILLISECONDS_PREHEAT_TIME 0
// @section extruder
-// Extruder runout prevention.
-// If the machine is idle and the temperature over MINTEMP
-// then extrude some filament every couple of SECONDS.
+/**
+ * Extruder runout prevention.
+ * If the machine is idle and the temperature over MINTEMP
+ * then extrude some filament every couple of SECONDS.
+ */
//#define EXTRUDER_RUNOUT_PREVENT
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
@@ -548,10 +554,14 @@
#endif
#endif
-// When first starting the main fan, run it at full speed for the
-// given number of milliseconds. This gets the fan spinning reliably
-// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
-//#define FAN_KICKSTART_TIME 100
+/**
+ * Fan Kickstart
+ * When part cooling or controller fans first start, run at a speed that
+ * gets it spinning reliably for a short time before setting the requested speed.
+ * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
+ */
+//#define FAN_KICKSTART_TIME 100 // (ms)
+//#define FAN_KICKSTART_POWER 180 // 64-255
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
@@ -870,6 +880,7 @@
#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
+//#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa
//#define QUICK_HOME // If G28 contains XY do a diagonal move first
//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
@@ -1176,7 +1187,7 @@
#endif
/**
- * Automatic backlash, position and hotend offset calibration
+ * Automatic backlash, position, and hotend offset calibration
*
* Enable G425 to run automatic calibration using an electrically-
* conductive cube, bolt, or washer mounted on the bed.
@@ -1350,7 +1361,7 @@
//
// LCD Backlight Timeout
//
-//#define LCD_BACKLIGHT_TIMEOUT 30 // (s) Timeout before turning off the backlight
+//#define LCD_BACKLIGHT_TIMEOUT_MINS 1 // (minutes) Timeout before turning off the backlight
#if HAS_BED_PROBE && EITHER(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
#define PROBE_OFFSET_WIZARD // Add a Probe Z Offset calibration option to the LCD menu
@@ -1459,37 +1470,43 @@
//#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
#endif
#if ENABLED(NEO2_COLOR_PRESETS)
- #define NEO2_USER_PRESET_RED 255 // User defined RED value
- #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value
- #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value
- #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value
- #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity
- //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip
+ #define NEO2_USER_PRESET_RED 255 // User defined RED value
+ #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value
+ #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value
+ #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value
+ #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity
+ //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip
#endif
#endif
-#endif
+#endif // HAS_DISPLAY || DWIN_LCD_PROUI
-// LCD Print Progress options
-#if EITHER(SDSUPPORT, SET_PROGRESS_MANUALLY)
- #if CAN_SHOW_REMAINING_TIME
- //#define SHOW_REMAINING_TIME // Display estimated time to completion
- #if ENABLED(SHOW_REMAINING_TIME)
- //#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
- //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
- #endif
+// Add the G-code 'M73' to set / report the current job progress
+#define SET_PROGRESS_MANUALLY
+#if ENABLED(SET_PROGRESS_MANUALLY)
+ //#define SET_PROGRESS_PERCENT // Add 'P' parameter to set percentage done, otherwise use Marlin's estimate
+ //#define SET_REMAINING_TIME // Add 'R' parameter to set remaining time, otherwise use Marlin's estimate
+ //#define SET_INTERACTION_TIME // Add 'C' parameter to set time until next filament change or other user interaction
+ #if ENABLED(SET_INTERACTION_TIME)
+ #define SHOW_INTERACTION_TIME // Display time until next user interaction ('C' = filament change)
#endif
+ //#define M73_REPORT // Report progress to host with 'M73'
+#endif
- #if EITHER(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI)
- //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
- #endif
+// LCD Print Progress options, multiple can be rotated depending on screen layout
+#if HAS_DISPLAY && EITHER(SDSUPPORT, SET_PROGRESS_MANUALLY)
+ #define SHOW_PROGRESS_PERCENT // Show print progress percentage (doesn't affect progress bar)
+ #define SHOW_ELAPSED_TIME // Display elapsed printing time (prefix 'E')
+ //#define SHOW_REMAINING_TIME // Display estimated time to completion (prefix 'R')
+
+ //#define PRINT_PROGRESS_SHOW_DECIMALS // Show/report progress with decimal digits, not all UIs support this
#if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
//#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
#if ENABLED(LCD_PROGRESS_BAR)
#define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
#define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
- #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
+ #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
//#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
//#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
#endif
@@ -1552,14 +1569,14 @@
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
#define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
- #define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
- #define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
+ //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
+ //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
- #define POWER_LOSS_STATE HIGH // State of pin indicating power loss
- #define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
+ //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
+ //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
//#define POWER_LOSS_PULLDOWN
- #define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
- #define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
+ //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
+ //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued.
@@ -1616,6 +1633,7 @@
#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
//#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
+ //#define M20_TIMESTAMP_SUPPORT // Include timestamps by adding the 'T' flag to M20 commands
#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
@@ -1777,7 +1795,7 @@
* Adds the menu item Configuration > LCD Timeout (m) to set a wait period
* from 0 (disabled) to 99 minutes.
*/
- //#define DISPLAY_SLEEP_MINUTES 2 // (minutes) Timeout before turning off the screen
+ //#define DISPLAY_SLEEP_MINUTES 2 // (minutes) Timeout before turning off the screen. Set with M255 S.
/**
* ST7920-based LCDs can emulate a 16 x 4 character display using
@@ -1831,14 +1849,8 @@
#endif // HAS_MARLINUI_U8GLIB
#if HAS_MARLINUI_U8GLIB || IS_DWIN_MARLINUI
- // Show SD percentage next to the progress bar
- //#define SHOW_SD_PERCENT
-
- // Enable to save many cycles by drawing a hollow frame on Menu Screens
- #define MENU_HOLLOW_FRAME
-
- // Swap the CW/CCW indicators in the graphics overlay
- //#define OVERLAY_GFX_REVERSE
+ #define MENU_HOLLOW_FRAME // Enable to save many cycles by drawing a hollow frame on Menu Screens
+ //#define OVERLAY_GFX_REVERSE // Swap the CW/CCW indicators in the graphics overlay
#endif
//
@@ -2094,13 +2106,18 @@
*
* See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
*/
-#define ADVANCE_K
-#if ENABLED(ADVANCE_K)
- //#define EXTRA_ADVANCE_K // Enable for second linear advance constants
- #define LIN_ADVANCE_K 0.0 // Unit: mm compression per 1mm/s extruder speed
- //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
- #define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
- //#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends.
+#define LIN_ADVANCE
+#if ENABLED(LIN_ADVANCE)
+ #if ENABLED(DISTINCT_E_FACTORS)
+ #define ADVANCE_K { 0.00 } // (mm) Compression length per 1mm/s extruder speed, per extruder
+ #else
+ #define ADVANCE_K 0.00 // (mm) Compression length applying to all extruders
+ #endif
+ //#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
+ //#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
+ #define EXPERIMENTAL_SCURVE // Allow S-Curve Acceleration to be used with LA.
+ //#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends.
+ //#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
#endif
// @section leveling
@@ -2558,7 +2575,7 @@
// Longer prime to clean out a SINGLENOZZLE
#define TOOLCHANGE_FS_EXTRA_PRIME 0 // (mm) Extra priming length
#define TOOLCHANGE_FS_PRIME_SPEED (4.6*60) // (mm/min) Extra priming feedrate
- #define TOOLCHANGE_FS_WIPE_RETRACT 0 // (mm) Retract before cooling for less stringing, better wipe, etc.
+ #define TOOLCHANGE_FS_WIPE_RETRACT 0 // (mm) Cutting retraction out of park, for less stringing, better wipe, etc. Adjust with LCD or M217 G.
// Cool after prime to reduce stringing
#define TOOLCHANGE_FS_FAN -1 // Fan index or -1 to skip
@@ -3224,7 +3241,7 @@
#define X2_HYBRID_THRESHOLD 100
#define Y_HYBRID_THRESHOLD 100
#define Y2_HYBRID_THRESHOLD 100
- #define Z_HYBRID_THRESHOLD 20
+ #define Z_HYBRID_THRESHOLD 20
#define Z2_HYBRID_THRESHOLD 3
#define Z3_HYBRID_THRESHOLD 3
#define Z4_HYBRID_THRESHOLD 3
@@ -3273,11 +3290,11 @@
#if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
// TMC2209: 0...255. TMC2130: -64...63
- #define X_STALL_SENSITIVITY 72
+ #define X_STALL_SENSITIVITY 8
#define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
- #define Y_STALL_SENSITIVITY 70
+ #define Y_STALL_SENSITIVITY 8
#define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
- #define Z_STALL_SENSITIVITY 10
+ //#define Z_STALL_SENSITIVITY 8
//#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
//#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
//#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
@@ -3288,7 +3305,7 @@
//#define V_STALL_SENSITIVITY 8
//#define W_STALL_SENSITIVITY 8
//#define SPI_ENDSTOPS // TMC2130 only
- #define IMPROVE_HOMING_RELIABILITY
+ //#define IMPROVE_HOMING_RELIABILITY
#endif
// @section tmc/config
@@ -3568,7 +3585,6 @@
*/
//#define LASER_POWER_TRAP
-
//
// Laser I2C Ammeter (High precision INA226 low/high side module)
//
@@ -4090,7 +4106,7 @@
/**
* Mechanical Gantry Calibration
- * Modern replacement for the Prusa TMC_Z_CALIBRATION.
+ * Modern replacement for the Průša TMC_Z_CALIBRATION.
* Adds capability to work with any adjustable current drivers.
* Implemented as G34 because M915 is deprecated.
* @section calibrate
@@ -4181,7 +4197,7 @@
/**
* WiFi Support (Espressif ESP32 WiFi)
*/
-//#define WIFISUPPORT // Marlin embedded WiFi managenent
+//#define WIFISUPPORT // Marlin embedded WiFi management
//#define ESP3D_WIFISUPPORT // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
#if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
github-actions[bot]
Did you test the latest
bugfix-2.1.xcode?Yes, and the problem still exists.
Bug Description
After flashing latest 2.1.x bugfix splashscreen is shown without issues (it is not connection issue) and when idle screen starts to render lower half of the screen remains from the splashscreen. Buttons doesn't work, no beeps and after second of frozen screen it resets and everything repeats.
I tried: 1) Changing UBL to bilinear 2) disabling boot and splash screen 3) disabling additional menu items like pid tuning etc to use less ram\flash 4) Disabling Input Shaping feature (I use bugfix branch to test this feature) because it was the main culprit 5) Increasing stack and heap sizes twofold
Behavior remains the same
Screen looks like this before reset
Config files used
Configuration.zip
PIO Inspect reports there is enough ram and flash
Bug Timeline
New bug on 2.1.x bugfix, 2.1.1 release works fine
Expected behavior
No response
Actual behavior
No response
Steps to Reproduce
No response
Version of Marlin Firmware
2.1.x bugfix
Printer model
No response
Electronics
SKR mini E3 V3
Add-ons
CR-Touch
Bed Leveling
UBL Bilinear mesh
Your Slicer
No response
Host Software
SD Card (headless)
Don't forget to include
Configuration.handConfiguration_adv.h.Additional information & file uploads
No response