EvilGremlin
commented
1 year ago Using firmware compiled by digant: https://www.thingiverse.com/thing:4294049
Then it's problem of this one digant, we don't support any 3rd party forks/builds. Build latest vanilla marlin yourself.
github-actions[bot]
Did you test the latest
bugfix-2.1.xcode?Yes, and the problem still exists.
Bug Description
Was at the intial first layer of print when printer stopped and message displayed. "V86 stored settings retrieved' (701 bytes; crc 60195" (printer may have truncated message following 701 as no closing bracket displayed. ) Unable to continue print. Re-powered printer and started print again. Print completed successfully. Repeated the print a few hours later with the same outcome.
Using firmware compiled by digant: https://www.thingiverse.com/thing:4294049. Marlin version 2.1.1
Bug Timeline
New bug
Expected behavior
Expected to be able to continue with the print and not have to re-start the printer. However, usure of exact cause of printer. Google searches seem to indicate an EEPROM read issue.
Actual behavior
No response
Steps to Reproduce
Issue seems to occur within first few layers of print. Only experienced with the one g-code file, but multiple times.
Version of Marlin Firmware
2.1.1
Printer model
Artillery X1
Electronics
Stock electronics
Add-ons
None
Bed Leveling
MBL Manual Bed Leveling
Your Slicer
Cura
Host Software
None
Don't forget to include
Configuration.handConfiguration_adv.h.Additional information & file uploads
Only configurable file using digant firware is the following 'config.ini' file used by the TFT firmware
--------------------------------------------------------------------
#
DEFAULT CONFIG FILE FOR BigTreeTech TFT CONTROLLERS
#
--------------------------------------------------------------------
--------------------------------------------------------------------
Supported TFT Variants
--------------------------------------------------------------------
#
BIGTREE_TFT24_V1_1 / BIGTREE_TFT28_V1_0 / BIGTREE_TFT28_V3_0
BIGTREE_TFT35_V1_0 / BIGTREE_TFT35_V1_1 / BIGTREE_TFT35_V1_2
BIGTREE_TFT35_V2_0 / BIGTREE_TFT35_V3_0 / BIGTREE_TFT35_E3_V3_0
BIGTREE_TFT35_B1_V3_0 / BIGTREE_TFT43_V3_0 / BIGTREE_TFT50_V3_0
BIGTREE_TFT70_V3_0
#
BIGTREE_GD_TFT24_V1_1 / BIGTREE_GD_TFT35_V2_0 / BIGTREE_GD_TFT35_V3_0
BIGTREE_GD_TFT35_E3_V3_0 / BIGTREE_GD_TFT35_B1_V3_0 / BIGTREE_GD_TFT43_V3_0
BIGTREE_GD_TFT50_V3_0 / BIGTREE_GD_TFT70_V3_0
#
MKS_TFT28_V3_0 / MKS_TFT28_V4_0 / MKS_TFT28_NEW_GENIUS
MKS_TFT32_V1_3 / MKS_TFT32_V1_4 / MKS_TFT35_V1_0
#
Firmware source: https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware
--------------------------------------------------------------------
Supported Marlin Firmware Versions
--------------------------------------------------------------------
#
Minimum Marlin firmware version: 2.1.1
Distribution date: 2022-08-06
Firmware source: https://github.com/MarlinFirmware/Marlin/releases
#
To use all the features and functionalities supported by the TFT,
the following options must be enabled in Marlin firmware.
#
General options which MUST be always activated:
EEPROM_SETTINGS (in Configuration.h)
BABYSTEPPING (in Configuration_adv.h)
AUTO_REPORT_TEMPERATURES (in Configuration_adv.h)
AUTO_REPORT_POSITION (in Configuration_adv.h)
M115_GEOMETRY_REPORT (in Configuration_adv.h)
M114_DETAIL (in Configuration_adv.h)
REPORT_FAN_CHANGE (in Configuration_adv.h)
#
Options to support printing from onboard media:
SDSUPPORT (in Configuration.h)
LONG_FILENAME_HOST_SUPPORT (in Configuration_adv.h)
AUTO_REPORT_SD_STATUS (in Configuration_adv.h)
SDCARD_CONNECTION ONBOARD (in Configuration_adv.h)
#
Options to support dialog with host:
EMERGENCY_PARSER (in Configuration_adv.h)
SERIAL_FLOAT_PRECISION 4 (in Configuration_adv.h)
HOST_ACTION_COMMANDS (in Configuration_adv.h)
HOST_PROMPT_SUPPORT (in Configuration_adv.h)
HOST_STATUS_NOTIFICATIONS (in Configuration_adv.h)
#
Options to support M600 with host & (Un)Load menu:
Options to support dialog with host (as pre requisite)
NOZZLE_PARK_FEATURE (in Configuration.h)
ADVANCED_PAUSE_FEATURE (in Configuration_adv.h)
PARK_HEAD_ON_PAUSE (in Configuration_adv.h)
FILAMENT_LOAD_UNLOAD_GCODES (in Configuration_adv.h)
#
Options to fully support Bed Leveling menu:
Z_MIN_PROBE_REPEATABILITY_TEST (in Configuration.h)
G26_MESH_VALIDATION (in Configuration.h)
Z_STEPPER_AUTO_ALIGN (in Configuration_adv.h)
--------------------------------------------------------------------
General Settings
--------------------------------------------------------------------
Serial Ports (Primary and Supplementary)
Serial ports connected to devices such as Printer, ESP3D, OctoPrint and other Controllers.
In order to successfully establish a communication through a serial port, set a baudrate
matching the baudrate configured on the connected device.
Disable the serial port when it is not in use and/or not connected to a device (floating) to
avoid to receive and process wrong data due to possible electromagnetic interference (EMI).
#
NOTES:
- Serial port P1 is the primary serial connection to the printer and cannot be disabled.
- A baudrate of 250000 works in most cases, but you can try a lower speed if you
commonly experience drop-outs during host printing.
You may try up to 1000000 to speed up SD file transfer.
#
Format: [serial_port: P1: P2: P3: P4:
Target port: P1: Printer
P2: WIFI (e.g. ESP3D)
P3: UART 3 (e.g. OctoPrint)
P4: UART 4
Value range: P1: [min: 1, max: 9]
P2: [min: 0, max: 9]
P3: [min: 0, max: 9]
P4: [min: 0, max: 9]
Options: [OFF (port disabled): 0, 2400: 1, 9600: 2, 19200: 3, 38400: 4, 57600: 5, 115200: 6, 250000: 7, 500000: 8, 1000000: 9]
serial_port:P1:7 P2:0 P3:0 P4:0
Emulated M600
The TFT intercepts the M600 G-code (filament change) and emulates the handling logic
otherwise provided by Marlin firmware.
#
NOTE: Enable it in case Marlin firmware does not properly support M600 on the mainboard.
#
Options: [disable: 0, enable: 1]
emulated_m600:0
Emulated M109 And M190
The TFT intercepts the blocking M109 and M190 G-codes (set target hotend and bed temperatures)
and converts them to the non-blocking M104 and M140 G-codes respectively.
#
NOTE: Enable it so the TFT can still communicate with Marlin firmware even if the target
temperature is not reached yet. Otherwise the communication (TFT<->Marlin) will be
frozen until desired/set temperatures are obtained.
#
Options: [disable: 0, enable: 1]
emulated_m109_m190:1
Event LED
When printing from TFT SD card / TFT USB disk, the TFT periodically sets the printer's (neopixel)
LED color and TFT's knob LED color, if any, according to the current nozzle and bed temperatures.
#
NOTE: If "emulated_m109_m190" is disabled (heating controlled by printer), the TFT cannot control the
printer's (neopixel) LED during heating. It will control only the TFT's knob LED, if any.
#
Options: [disable: 0, enable: 1]
event_led:1
G-code File Comment Parsing
The TFT parses and processes extra information provided by the slicer as comments in the G-code file.
If enabled, the current implementation parses and processes print time and print layer information
from the G-code file (nothing else).
If disabled, the "layer_disp_type" setting provided in "UI Settings" section becomes redundant.
#
NOTE: Enable it in case the slicer (e.g. Cura) supports extra information.
#
Options: [disable: 0, enable: 1]
file_comment_parsing:1
--------------------------------------------------------------------
UI Settings
--------------------------------------------------------------------
Rotated UI
Rotate UI by 180 degrees.
Options: [disable: 0, enable: 1]
rotated_ui:0
Touch Mode Language
Select the language to use on the LCD while in Touch Mode.
#
NOTE: To add/flash a second language copy the required "language_xx.ini" file from
"Language Packs" folder to the SD root folder.
Then press the reset button to load/flash the copied language file.
#
Options: [Primary Language (english): 0, Secondary Language: 1]
language:0
Status Screen
Select the default home screen while in Touch Mode.
If enabled, the Status Screen menu will become the default home screen.
If disabled, the Main menu will become the default home screen.
#
NOTE: Both the Status Screen and Main menus display the current temperature, fan and speeds.
Furthermore, the Status Screen menu provides the status area reporting the printer notifications.
#
Options: [disable: 0, enable: 1]
status_screen:1
Touch Mode Colors
Set colors used in Touch Mode.
#
NOTE: Select an option from the provided list or set the color (RGB888 format) hex value directly
(start with "0x"), such as: Red: 0xFF0000, Green: 0x00FF00, Blue: 0x0000FF.
#
Options: [ WHITE: 0, BLACK: 1, RED: 2, GREEN: 3, BLUE: 4, CYAN: 5, MAGENTA: 6, YELLOW: 7,
ORANGE: 8, PURPLE: 9, LIME: 10, BROWN: 11, DARKBLUE: 12, DARKGREEN: 13, GRAY: 14, DARKGRAY: 15]
Title background color
title_background_color:1
Menu background color
menu_background_color:1
Menu font color
menu_font_color:0
Reminder font color, such as: "No print attached", "Busy processing", etc.
reminder_font_color:2
Status (e.g. volume reminder, ABL probing point etc.) font color, such as: "Card inserted", "Card removed"
status_font_color:5
Background color for X Y Z position display in Status Screen menu
status_xyz_bg_color:15
List View border color
list_border_color:15
List View button background color
list_button_bg_color:15
Color used by the Mesh Editor menu for drawing the mesh with the minimum value in the grid
mesh_min_color:7
Color used by the Mesh Editor menu for drawing the mesh with the maximum value in the grid
mesh_max_color:2
Terminal Text Color Scheme
Color scheme for displaying text in Terminal menu.
Options: [Material Dark: 0, Material Light: 1, High Contrast: 2]
Material Dark: Dark background with light font color and orange command font color.
Material Light: Light background with dark font color and orange command font color.
High Contrast: Black background with white font color and orange command font color.
terminal_color_scheme:2
Notification Style For ACK Messages
Set the notification style to use for displaying the ACK messages which start with "echo:".
#
NOTE: The OFF value is applied to any ACK message type (e.g. even to known echo ACK).
It means that any kind of ACK message is silently discarded.
#
Options: [OFF: 0, POPUP: 1, TOAST: 2]
OFF: No notification. The message is ignored.
POPUP: Display a popup window for user confirmation.
TOAST: A non-blocking Toast notification is displayed for few seconds. No user interaction is needed.
ack_notification:1
Files Sorting
Sort files and folders based on the selected option.
#
NOTE: Only applicable for files in TFT SD card and TFT USB disk.
#
Options: [Date Newest First: 0, Date Oldest First: 1, Name Ascending: 2, Name Descending: 3]
files_sort_by:0
Files List Mode
Display files in list mode instead of icon mode.
Options: [disable: 0, enable: 1]
files_list_mode:1
Filename Extension
Display fullname for files listed in List Mode / Icon Mode menu.
If disabled, any filename extension starting with ".g" or ".G" (e.g. ".g", ".gco", ".gcode" etc.) will be hidden.
Options: [disable: 0, enable: 1]
filename_extension:1
Fan Speed In Percentage
Show fan speed in percentage. If disabled fan speed will be displayed as PWM values.
Options: [disable: 0, enable: 1]
fan_speed_percentage:1
Persistent Temperature Info
Show persistent temperature info in all menus.
Options: [disable: 0, enable: 1]
persistent_info:1
Temperature And Wait ACK In Terminal
Show "temperature" and "wait" ACK in Terminal menu.
Options: [disable: 0, enable: 1]
terminal_ack:0
Notification M117
If enabled, any notification received from Marlin through "//action:notification" is also
stored on the notification screen. The notification screen reporting the history of the
received notifications is displayed pressing on the notification bar.
#
NOTE: Marlin notifications are also always displayed on the Status Screen menu.
Furthermore, they are also displayed on the notification bar as toast messages
in case the current menu is not the Status Screen menu.
#
Options: [disable: 0, enable: 1]
notification_m117:0
Progress Source
This sets the source of the progress calculation, G-code file advance based or time based.
In file mode it is a simple file progress, it tells you the percentage of the G-codes
executed. It doesn't reflect the amount of work done, only in a very few cases (ex. a 2D
shape expanded vertically like a cylinder, cube, etc).
Time based mode is very close to the real amount of work done, but it is still not perfect,
it relies on the estimate the slicer has done. It needs info from the slicer, the elapsed
time or the remaining time, if it's missing, the progress source defaults to file progress
mode. If no "M73 R" is present in the G-code file than it requires "file_comment_parsing"
to be enabled.
#
NOTE: If "M73 P" is present in the G-code file than file or time based progress will be
overriden by that.
#
Options: [File progress mode: 0, Time based progress: 1]
prog_source:0
Progress Numeric Display Mode During Print
This sets the default display type for print progress numeric display. It can be changed during
print by pressing the hourglass icon.
At each click it will alter between the 3 variants.
#
NOTE: Some slicers include time related info in the G-code files as comments. If the time info
is not added by the slicer, then a post processing plugin is needed that adds that info in
the G-code file (comment or M73 Rxx format).
If no remaining time info is present in the G-code file (comment or M73 Rxx), the display
defaults to option 0.
#
Options: [Percentage & Elapsed time: 0, Percentage & Remaining time: 1, Elapsed time & Remaining time: 2]
prog_disp_type:2
Current Layer Display Mode During Print
This sets the default display type for the printing layer. It can be changed during print by
pressing the nozzle icon. At each click it will alter between the 3 variants.
#
NOTES:
- It requires "file_comment_parsing" to be enabled.
- This feature uses the layer number comments added by slicers at the starting of each layer.
- Some slicers may not include the total number of layers in the G-code file. In this case only
the current layer will be displayed. To display total number of layers, a comment should be
added at the beginning of the G-code file in the format "; Layer count: xx".
Separators can be " ", ":", "_" or "=".
- If the total number of layers exceeds 999, this information will not be displayed because
there is not enough space for both current and total layer number to be shown.
#
- For PrusaSlicer, to enable this feature, following comment lines must be added in
Printer Settings -> Custom G-code section:
- In After layer change G-code section:
";LAYER:[layer_num]"
- In Start G-code section:
";LAYER_COUNT:[total_layer_count]"
#
Options: [Layer height: 0, Layer number: 1, Both - height & number: 2]
layer_disp_type:0
--------------------------------------------------------------------
Marlin Mode Settings (only for TFT24 V1.1 & TFT28/TFT35/TFT43/TFT50/TFT70 V3.0)
--------------------------------------------------------------------
Default Mode
Set Marlin/Touch Mode as the default mode at startup.
#
NOTE: Mode switching is possible only for Marlin Mode and Touch Mode by a long press of
1.5 seconds on the display or holding down the encoder button for 1.5 seconds.
#
Options: [Marlin Mode: 0, Touch Mode: 1, Blocked Marlin Mode: 2, Blocked Touch Mode: 3]
default_mode:1
Serial Always ON
Keep UART (serial communication) alive in Marlin Mode.
Allows seamless OctoPrint UART connection to the TFT's UART/serial expansion port
no matter which mode the TFT is in.
Options: [disable: 0, enable: 1]
serial_always_on:0
Marlin Mode Background & Font Colors
Set colors used in Marlin Mode.
#
NOTE: Select an option from the provided list or set the color (RGB888 format) hex value directly
(start with "0x"), such as: Red: 0xFF0000, Green: 0x00FF00, Blue: 0x0000FF.
#
Options: [ WHITE: 0, BLACK: 1, RED: 2, GREEN: 3, BLUE: 4, CYAN: 5, MAGENTA: 6, YELLOW: 7,
ORANGE: 8, PURPLE: 9, LIME: 10, BROWN: 11, DARKBLUE: 12, DARKGREEN: 13, GRAY: 14, DARKGRAY: 15]
Marlin Mode background color
marlin_background_color:1
Marlin Mode font color
marlin_font_color:8
Fullscreen Marlin Mode
Run Marlin Mode in fullscreen.
#
NOTE: Disable is recommended for TFT24.
#
Options: [disable: 0, enable: 1]
marlin_fullscreen:1
Show Marlin Mode Title
Show banner text at the top of the TFT in Marlin Mode.
Options: [disable: 0, enable: 1]
marlin_show_title:1
Marlin Mode Title
Banner text displayed at the top of the TFT in Marlin Mode.
Value range: [min: 3, max: 20 characters]
marlin_title:Marlin Mode
Marlin Mode Type
Select Marlin Mode type.
Options: [128x64 Full Graphic LCD: 0, 20x4 Character LCD: 1]
marlin_type:0
--------------------------------------------------------------------
Printer / Machine Settings
--------------------------------------------------------------------
Hotend Count
Value range: [min: 0, max: 6]
hotend_count:1
Heated Bed Support
Options: [disable: 0, enable: 1]
heated_bed:1
Heated Chamber Support
The TFT will auto-detect if chamber heating is enabled in Marlin firmware.
Options: [disable: 0, enable: 1]
heated_chamber:0
Extruder Count
Value range: [min: 0, max: 6]
ext_count:1
Fan Count
Value range: [min: 1, max: 6]
fan_count:1
Controller Fan Support
Enable/disable controller fan speed control for Active and Idle cooling if Marlin
firmware supports controller fan (M710).
Options: [disable: 0, enable: 1]
controller_fan:0
Bed / Extruder / Chamber Maximum Temperatures
Format: [max_temp: T0: T1: T2: T3: T4: T5: BED: CHAMBER:]
Unit: [temperature in °C]
Value range: hotend: [min: 20, max: 1000]
bed: [min: 20, max: 400]
chamber: [min: 20, max: 200]
max_temp:T0:275 T1:275 T2:275 T3:275 T4:275 T5:275 BED:150 CHAMBER:60
Cold Extrusion Minimum Temperature
Minimum temperature needed to extrude/retract.
Any extrusion/retraction below this temperature will be prevented.
Unit: [temperature in °C]
Value range: [min: 20, max: 1000]
min_temp:180
Fan Maximum PWM Speed
Set minimum and maximum fan speed allowed by the printer for Cooling Fans & Controller Fan.
Cooling fans have index from F0 to F5.
Controller fan has index CtA and CtI (Active and Idle). It requires "controller_fan" to be enabled.
Format: [fan_max: F0: F1: F2: F3: F4: F5: CtA: CtI:]
Unit: [PWM]
Value range: [min: 25, max: 255]
fan_max:F0:255 F1:255 F2:255 F3:255 F4:255 F5:255 CtA:255 CtI:255
Machine Size / Build Area
The TFT will auto-detect the machine size (min and max) in Marlin firmware (requires
enabling "M115_GEOMETRY_REPORT" in Configuration_adv.h in Marlin firmware).
Format: [size_min: X Y Z]
[size_max: X Y Z]
Unit: [distance in mm]
Value range: [min: -2000, max: 2000]
size_min:X0 Y0 Z0 size_max:X300 Y300 Z400
X & Y Move Speeds/Feedrates
Move speeds used in Move menu to move X and Y axes.
Format: [move_speed: S N F]
Unit: [feedrate in mm/min]
Value range: [min: 10, max: 12000]
xy_speed:S1000 N3000 F5000
Z Speeds/Feedrates
Move speeds used in Move menu to move Z axis.
Format: [move_speed: S N F]
Unit: [feedrate in mm/min]
Value range: [min: 10, max: 12000]
z_speed:S500 N1000 F2000
Extruder Speeds/Feedrates
Speed settings used to extrude/retract.
Format: [ext_speed: S N F]
Unit: [feedrate in mm/min]
Value range: [min: 10, max: 12000]
ext_speed:S60 N600 F1200
Auto Save/Load Bed Leveling Data
The TFT will auto-detect if Auto Bed Level is available.
Enable this will send "M500" after "G29" to store leveling value and send "M420 S1"
to enable leveling state after startup.
Options: [disable: 0, enable: 1]
auto_load_leveling:1
Onboard / Printer Media Support
On Marlin firmware, the TFT will auto-detect onboard media.
Auto-detect is not available for other firmwares like Smoothieware.
Options: [disable: 0, enable: 1, auto-detect: 2]
onboard_sd:2
M27 Printing Status Refresh Time
M27 printing status refresh time (this will be used if SD_AUTOREPORT is not detected by the TFT).
Unit: [time in seconds]
Value range: [min: 1, max: 100]
M27_refresh_time:3
M27 Always Active
Keep polling M27 even if not printing (e.g. SD print not started from TFT).
Options: [disable: 0, enable: 1]
M27_always_active:1
Long File Names Support
On Marlin firmware, the TFT will auto-detect Long File Name support.
Auto-detect is not available for other firmwares like Smoothieware.
Options: [disable: 0, enable: 1, auto-detect: 2]
long_filename:2
Pause/Nozzle Park Settings
These settings are used when a print is paused or in any feature which requires moving/parking the nozzle
before performing a task like in (Un)Load or Extruder Tuning menus.
Pause Retract Length
Format: [pause_retract: R P]
Unit: [length in mm]
Value range: [min: 0.0, max: 20.0]
pause_retract:R15.0 P16.0
Pause XY Position
NOTES:
- It MUST BE a value >= 0 for a Cartesian printer.
- It MUST BE a value <= 0 for a Delta printer.
#
Format: [pause_pos: X Y]
Unit: [position in mm]
Value range: [min: -2000.0, max: 2000.0]
pause_pos:X10.0 Y10.0
Pause Z Raise
Raise Z axis by this value relative to the current layer height.
Unit: [distance in mm]
Value range: [min: 0.0, max: 2000.0]
pause_z_raise:10.0
Pause Feed Rate
Feedrate to use when moving an axis when printing is paused.
Format: [pause_feedrate: XY Z E]
Unit: [feedrate in mm/min]
Value range: [min: 10, max: 12000]
pause_feedrate:XY6000 Z6000 E600
Leveling Settings
These settings are used for leveling.
Leveling Edge Distance (Manual Leveling, Leveling Corner)
Inset distance from bed edges. This distance is added to minimum X & Y bed coordinates and
subtracted from maximum X & Y bed coordinates to calculate manual leveling points.
For Leveling Corner, the default distance is the maximum between this setting value and
the rounded probe offset X/Y values configured in Marlin firmware.
Unit: [distance in mm]
Value range: [min: 0, max: 2000]
level_edge_distance:20
Leveling Z Position (Manual Leveling, Leveling Corner, Mesh Leveling, Probe/Home Offset, Mesh Tuner)
For Manual Leveling and MBL, lower Z axis to this absolute position after reaching a leveling point.
For Probe/Home Offset and ABL in Mesh Tuner, raise Z axis by this relative position after reaching
a leveling point.
Unit: [position in mm]
Value range: [min: 0.0, max: 2000.0]
level_z_pos:0.1
Leveling Z Raise (Manual Leveling, Leveling Corner, Mesh Leveling)
Raise Z axis by this relative value before moving to another point during leveling/probing procedures.
Unit: [distance in mm]
Value range: [min: 0.0, max: 2000.0]
level_z_raise:10.0
Leveling Feed Rate (Manual Leveling, Leveling Corner, Mesh Leveling)
Feedrate to use when moving an axis during leveling/probing procedures.
Format: [level_feedrate: XY Z]
Unit: [feedrate in mm/min]
Value range: [min: 10, max: 12000]
level_feedrate:XY6000 Z6000
Inverted Axes (Manual Leveling, Leveling Corner, Move, Probe Offset)
Used by Manual Leveling, Leveling Corner, Move and Probe Offset menus in order axis matches the actual axis movement.
#
NOTE: The Y axis of different printer (move hotbed or move nozzle) move in different directions.
So Y axis leveling inversion can't follow up inverted_axis[Y_AXIS].
We separate a single variable "LY" (Leveling Y axis) to deal with the Y axis leveling movement direction.
#
Format: [X
Options: [disable: 0, enable: 1]
inverted_axis:X0 Y0 Z0 LY0
Probing For Z Offset (Probe Offset)
Used by the Probe Offset menu for the Z offset tuning process.
If enabled, after homing a probing in the center of the bed is performed and then the nozzle
is moved to the XY probing point.
If disabled, after homing the nozzle is moved directly to the XY homing point. This is useful
in case Marlin firmware is configured to use the probe for Z axis homing (e.g.
USE_PROBE_FOR_Z_HOMING enabled in Marlin firmware) to avoid a second probing after homing.
#
NOTES:
- Enable it in case Marlin firmware is not configured to use the probe for Z axis homing
(e.g. USE_PROBE_FOR_Z_HOMING disabled in Marlin firmware) or the XY probing point set
for homing is not reachable by the nozzle (e.g. due to HW limitations/constraints or
printer specific configuration).
- Disable it (preferably) in case Marlin firmware is configured to use the probe for Z axis
homing (e.g. USE_PROBE_FOR_Z_HOMING enabled in Marlin firmware).
#
Options: [disable: 0, enable: 1]
probing_z_offset:1
Probing Z Raise (Probe Offset, Mesh Editor)
Used by the Probe Offset / Mesh Editor menu for the Z offset / Z height tuning process.
Raise / drop Z axis by this relative value after homing (G28) before starting to probe a point.
#
NOTES:
- It MUST BE a value >= 0 (e.g. 20) for a Cartesian printer to avoid crashing into the bed.
- It MUST BE a value <= 0 (e.g. -50) for a Delta printer to avoid crashing into the top of the tower.
#
Unit: [distance in mm]
Value range: [min: -2000.0, max: 2000.0]
probing_z_raise:20.0
Z Steppers Auto-Alignment (ABL)
It allows to align multiple Z stepper motors using a bed probe by probing one position per stepper.
Enable this setting to show an icon in ABL menu allowing to run G34 command (it requires
Z_STEPPER_AUTO_ALIGN enabled in Configuration_adv.h in Marlin firmware).
#
NOTE: Only for Marlin printers with one stepper driver per Z stepper motor and no Z timing belt.
#
Options: [disable: 0, enable: 1]
z_steppers_alignment:1
TouchMI Settings (ABL)
Enable this option for displaying TouchMI sensor settings in ABL menu (Init, Z Offset, Save, Test).
Options: [disable: 0, enable: 1]
touchmi_sensor:0
Preheat Temperatures
Format: [preheat_name_X:]
[preheat_temp_X:T B]
Unit: [temperature in °C]
Value range: name: [min: 3, max: 20 characters]
hotend temp: [min: 20, max: 1000]
bed temp: [min: 20, max: 400]
preheat_name_1:PLA preheat_temp_1:T210 B70
preheat_name_2:PETG preheat_temp_2:T240 B70
preheat_name_3:ABS preheat_temp_3:T230 B90
preheat_name_4:WOOD preheat_temp_4:T170 B50
preheat_name_5:TPU preheat_temp_5:T220 B50
preheat_name_6:NYLON preheat_temp_6:T250 B90
--------------------------------------------------------------------
Power Supply Settings (only if connected to TFT controller)
--------------------------------------------------------------------
Active HIGH Power Supply Logic
Used in case it is supported by the TFT.
The power supply uses this HIGH signal logic to stay ON.
The power supply uses the opposite of this logic to stay OFF.
Options: [disable: 0, enable: 1]
ps_active_high:1
Power Supply Auto Shutdown Mode
Used in case it is supported by the TFT.
Enable power supply auto shutdown after a print is finished when hotend temperature drops below target value.
Options: [disable: 0, enable: 1, auto-detect: 2]
ps_auto_shutdown:0
Power Supply Auto Shutdown Temperature
Maximum hotend temperature for automatic shutdown after printing, if automatic shutdown is enabled.
The printer will shutdown automatically if the hotend temperature is below this value.
If the hotend temperature is higher than this value the fans will be turned on to cooldown and it
will wait for the hotend temperature to drop below this value before shutting down automatically.
Unit: [temperature in °C]
Value range: [min: 20, max: 1000]
ps_auto_shutdown_temp:50
--------------------------------------------------------------------
Filament Runout Settings (only if connected to TFT controller)
--------------------------------------------------------------------
NOTES for users having a filament sensor connected to the mainboard:
1) Define "fil_runout:0" below to disable the sensor handling on the TFT.
2) Configure the sensor in the firmware of your mainboard.
3) Add M75 to "start_gcode" and M77 to "end_gcode" of the TFT (or your slicer).
Filament Runout Sensor
Select the type of filament runout sensor and its default enabled/disabled state.
Options: [Normal Disabled: 0, Normal Enabled: 1, Smart Disabled: 2, Smart Enabled: 3]
fil_runout:0
Inverted Filament Runout Sensor Logic
The sensor uses an inverted logic.
Disable it in case filament runout is triggered by a LOW signal.
Enable it in case filament runout is triggered by a HIGH signal.
Options: [disable: 0, enable: 1]
fil_runout_inverted:0
NC (Normal Close) Filament Runout Sensor
The sensor is of type NC.
Options: [Normal Open: 0, Normal Close: 1]
fil_runout_nc:1
Filament Runout Noise Threshold
Pause print when filament runout is detected at least for this time period.
Unit: [time in milliseconds]
Value range: [min: 10, max: 1800]
fil_runout_noise_threshold:200
Smart Filament Runout Detection
Used in conjunction with an SFS (Smart Filament Sensor) based on an encoder disc that
toggles runout pin as filament moves.
Unit: [distance in mm]
Value range: [min: 1, max: 50]
fil_runout_distance:7
--------------------------------------------------------------------
Power Loss Recovery & BTT UPS Settings
--------------------------------------------------------------------
Power Loss Recovery Mode
Enable power loss recovery.
Disable to reduce the loss of TFT SD card or TFT USB disk.
Options: [disable: 0, enable: 1]
pl_recovery:1
Power Loss Recovery Homing
Home before power loss recovery.
Options: [disable: 0, enable: 1]
pl_recovery_home:0
Power Loss Recovery Z Raise
Raise Z axis on resume (on power loss with UPS).
Unit: [distance in mm]
Value range: [min: 0.0, max: 2000.0]
pl_recovery_z_raise:10.0
BTT Mini UPS Support
Enable backup power/UPS to move Z axis on power loss.
Options: [disable: 0, enable: 1]
btt_mini_ups:0
--------------------------------------------------------------------
Other Device-Specific Settings
--------------------------------------------------------------------
Sounds / Buzzer
Set sound ON or OFF.
#
NOTE: Error messages from printer will always play the error sound.
#
Parameters:
touch_sound: Enable/disable this to control touch feedback sound.
toast_sound: Enable/disable this to control all toast notification sounds.
alert_sound: Enable/disable this to control all popup and alert sounds
like print finish alert, dialog sound etc.
heater_sound: Enable/disable this to control acoustic feedback when temperature
has reached the desired value on heaters (nozzle, bed, chamber).
#
Options: [disable: 0, enable: 1]
touch_sound:1 toast_sound:1 alert_sound:1 heater_sound:1
LCD Brightness Levels (only for TFT28/TFT35/TFT43/TFT50/TFT70 V3.0)
Brightness levels for LCD.
Options: [OFF: 0, 5%: 1, 10%: 2, 20%: 3, 30%: 4, 40%: 5, 50%: 6, 60%: 7, 70%: 8, 80%: 9, 90%: 10, 100%: 11]
LCD brightness level
lcd_brightness:11
LCD brightness level when device is idle
lcd_idle_brightness:5
LCD Idle Time (only for TFT28/TFT35/TFT43/TFT50/TFT70 V3.0)
The LCD screen will dim to idle brightness, if the display is not touched for the
period of the LCD idle time.
Options: [OFF: 0, 5sec: 1, 10sec: 2, 30sec: 3, 1min: 4, 2min: 5, 5min: 6, 10min: 7]
lcd_idle_time:4
LCD Lock On Idle (only for TFT28/TFT35/TFT43/TFT50/TFT70 V3.0)
If enabled, when the LCD is idle (dimmed) then the first touch on the display will
simply restore the normal LCD brightness. The touch is then skipped, preventing to
trigger any undesired action due to the dimmed display.
#
NOTE: The lock is always avoided if the LCD brightness is restored by the use of
rotary encoder instead of touching the display.
#
Options: [disable: 0, enable: 1]
lcd_lock_on_idle:0
LED Color
Printer's LED color used by some features such as Event LED and PID processes.
Format: [led_color: R: G: B: W: P: I:
Target component: R: Red
G: Green
B: Blue
W: White; NEOPIXEL or RGB(W)
P: Intensity; NEOPIXEL
I: Index; NEOPIXEL
Value range: [min: 0, max: 255]
led_color:R:255 G:255 B:255 W:255 P:255 I:255
LED Always ON
Keep printers's LED on at startup and after Event LED and PID processes terminate.
The printer's LED color is configured in "led_color".
Options: [disable: 0, enable: 1]
led_always_on:0
Knob LED Color (only for TFT28/TFT35_E3/TFT43/TFT50/TFT70 V3.0)
Knob LED color at startup.
Options: [OFF: 0, WHITE: 1, RED: 2, ORANGE: 3, YELLOW: 4, GREEN: 5, BLUE: 6, INDIGO: 7, VIOLET: 8]
knob_led_color:0
Knob LED Idle State (only for TFT28/TFT35_E3/TFT43/TFT50/TFT70 V3.0)
If enabled, when the LCD is idle (dimmed) then the knob LED will be also switched off.
Options: [disable: 0, enable: 1]
knob_led_idle:1
Knob LED Pixels (only for TFT28/TFT35_E3/TFT43/TFT50/TFT70 V3.0)
Set the number of LEDs in the strip connected to "Neopixel" port of TFT.
It shares the same signal line as "knob_led". 0 means the default number in TFT hardware.
Greater than 0 means the number of LEDs in the strip.
Value range: [min: 0, max: 200]
neopixel_pixels:0
--------------------------------------------------------------------
Custom G-code Commands
--------------------------------------------------------------------
Custom G-code Commands
Up to 15 custom G-code commands that will be available in the Custom menu.
#
Usage:
- To enable a custom command, remove "#" at the beginning of custom commands label & G-code.
- To disable a custom command, add "#" at the beginning of custom commands label & G-code.
#
NOTE: If the values are left blank then default name and G-code will be used.
#
Value range: label: [min: 3, max: 75 characters]
G-code: [min: 3, max: 75 characters]
custom_label_1:Present extruder custom_gcode_1:G90\nG0 F3000 X0 Y0 Z100\n custom_label_2:Present bed custom_gcode_2:G90\nG0 F3000 X0 Y250 Z100\n custom_label_3:Disable all steppers custom_gcode_3:M84\n
custom_label_4:custom4
custom_gcode_4:M105\n
custom_label_5:custom5
custom_gcode_5:M105\n
custom_label_6:custom6
custom_gcode_6:M105\n
custom_label_7:custom7
custom_gcode_7:M105\n
custom_label_8:custom8
custom_gcode_8:M105\n
custom_label_9:custom9
custom_gcode_9:M105\n
custom_label_10:custom10
custom_gcode_10:M105\n
custom_label_11:custom11
custom_gcode_11:M105\n
custom_label_12:custom12
custom_gcode_12:M105\n
custom_label_13:custom13
custom_gcode_13:M105\n
custom_label_14:custom14
custom_gcode_14:M105\n
custom_label_15:custom15
custom_gcode_15:M105\n
--------------------------------------------------------------------
Start, End & Cancel G-code Commands
--------------------------------------------------------------------
NOTES for users having a filament sensor connected to the mainboard:
1) Enable the start/end G-code below.
2) Add the following commands to the start/end G-code:
- start_gcode: M75\n
- end_gcode: M77\n
Start G-code Status
Options: [disable: 0, enable: 1]
start_gcode_enabled:0
End G-code Status
Options: [disable: 0, enable: 1]
end_gcode_enabled:0
Cancel G-code Status
Options: [disable: 0, enable: 1]
cancel_gcode_enabled:1
Start G-code
This G-code will run before starting a print if "start_gcode_enabled" is enabled.
Value range: [min: 3, max: 75 characters]
start_gcode:G28 XY R20\n
End G-code
This G-code will run after a print is completed if "end_gcode_enabled" is enabled.
Value range: [min: 3, max: 75 characters]
end_gcode:M104 S0\nM140 S0\nM107\nM18\n
Cancel G-code
This G-code will run when a print is cancelled if "cancel_gcode_enabled" is enabled.
Value range: [min: 3, max: 75 characters]
cancel_gcode:M104 S0\nM140 S0\nG28 XY R10\nM107\nM18\n