search

MathewWi / sneek

Automatically exported from code.google.com/p/sneek
0 stars 0 forks source link

UNEEK not working for USB drive where sneek-di works fine #61

Open GoogleCodeExporter opened 9 years ago

GoogleCodeExporter commented 9 years ago 
What steps will reproduce the problem?
1.  Copy NAND to USB Flash drive
2.  Copy sneek/kernel.bin sneek/font.bin to both SD card and flash drive
3.  Start Wii

What is the expected output? What do you see instead?
My flash drive (a sandisk mini cruzer 16GB) has an orange light that flashes 
with activity on the drive, I see it briefly flashing quickly than going to a 
slow flash (which it does any time its powered and not active).  No video 
output makes it to my TV.  The interesting thing is the same flash drive works 
with sneek-di holding games and any other homebrew use i've put it to 
(cfg-loader, wiimc, etc.), which would lead me to believe there's some 
difference between the uneek usb loading and the di loading that makes the 
difference.  I've used both the sneek installer and compiling my own from 
source and the problem persists across both.

What revision are you using? With what configuration
(SNEEK/UNEEK/SNEEK+DI)?
UNEEK 106+ (and probably earlier versions)

Original issue reported on code.google.com by NReale3...@gmail.com on 26 Jul 2010 at 12:35

GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
Interestingly the armboot.bin from 110 gives sneek-di the same behavior, not 
even creating the diconfig.bin.  Tried with both IOS 70 and 80, same effect

Original comment by NReale3...@gmail.com on 26 Jul 2010 at 4:59

GoogleCodeExporter commented 9 years ago 
did you try deleting the shared2 folder from your NAND? I can only get it to 
boot from a fresh Wii setup.

See my issue here, maybe they are the same?

http://code.google.com/p/sneek/issues/detail?id=65

Original comment by retroh...@gmail.com on 28 Jul 2010 at 11:39

GoogleCodeExporter commented 9 years ago 
Thanks for the tip, tried that and same thing.  Also tried building a virgin 
NAND for the hell of it

Original comment by NReale3...@gmail.com on 28 Jul 2010 at 7:40

GoogleCodeExporter commented 9 years ago 
and by same thing i mean the same problem

Original comment by NReale3...@gmail.com on 28 Jul 2010 at 7:41

GoogleCodeExporter commented 9 years ago 
with 110 only sneek-sd works, anything with usb hangs after one blink of the 
flash drive

Original comment by NReale3...@gmail.com on 28 Jul 2010 at 8:00

GoogleCodeExporter commented 9 years ago 
I workaround this (even with r114) by turning on the wii WITHOUT the SD card.
Wait for the health screen -> put in the SD card and press reset
Now sneeks loads without problems (UNEEK and UNEEK+DI) (WD Essentials 1TB FAT32 
32kb)
Otherwise it will flash 3 times (cannot find kernel.bin) and no screen output.
This has to do with slow usb devices like thulinma stated.
Waiting for the health screen, you can hear the drive spinning up.

Original comment by digd...@zonnet.nl on 1 Aug 2010 at 12:22

GoogleCodeExporter commented 9 years ago 
Brilliant! UNEEK works as well as sneek-di which stopped working for me after 
r110.  UNEEK-DI still doesn't work, flash drive blinks for a while and it bombs 
out, no blinking and no diconfig.bin being written.  Is there a change I can 
make to the source to add in a delay or something for my flash drive to make 
life easier?

Original comment by NReale3...@gmail.com on 1 Aug 2010 at 5:15

GoogleCodeExporter commented 9 years ago 
Added the delays from issue 54 (the two udelays in the original patch there) 
and that helped, thank you again!

Original comment by NReale3...@gmail.com on 1 Aug 2010 at 6:08