Pinout incorrect, no instructions for flashing Klipper firmware

[wandersoulz]

The Gemini V3 board that I have does not have an SD card specific to the board itself. As such there is no way to flash the new klipper firmware and there are no instructions on how to do a command line based flashing.

[jaysuk]

sudo apt install libusb-1.0 pkg-config cd ~/klipper/lib/hidflash make sudo ~/klipper/lib/hidflash/hid-flash ~/klipper/out/klipper.bin

On Wed, 21 Dec 2022, 16:34 wandersoulz, @.***> wrote:

The Gemini V3 board that I have does not have an SD card specific to the board itself. As such there is no way to flash the new klipper firmware and there are no instructions on how to do a command line based flashing.

— Reply to this email directly, view it on GitHub https://github.com/Mellow-3D/Fly-Gemini-V3/issues/1, or unsubscribe https://github.com/notifications/unsubscribe-auth/AATUSBQ7FY5UK7IFVPPH7JDWOMWQRANCNFSM6AAAAAATFZ6G7M . You are receiving this because you are subscribed to this thread.Message ID: @.***>

[jaysuk]

Make the firmware the same as the Gemini v2

On Wed, 21 Dec 2022, 16:34 wandersoulz, @.***> wrote:

The Gemini V3 board that I have does not have an SD card specific to the board itself. As such there is no way to flash the new klipper firmware and there are no instructions on how to do a command line based flashing.

— Reply to this email directly, view it on GitHub https://github.com/Mellow-3D/Fly-Gemini-V3/issues/1, or unsubscribe https://github.com/notifications/unsubscribe-auth/AATUSBQ7FY5UK7IFVPPH7JDWOMWQRANCNFSM6AAAAAATFZ6G7M . You are receiving this because you are subscribed to this thread.Message ID: @.***>

[wandersoulz]

These commands do not work for me. This is the output from running the hid-flash command:

+-----------------------------------------------------------------------+
|         HID-Flash v2.2.1 - STM32 HID Bootloader Flash Tool            |
|     (c)      2018 - Bruno Freitas       http://www.brunofreitas.com   |
|     (c) 2018-2019 - Vassilis Serasidis  https://www.serasidis.gr      |
|   Customized for STM32duino ecosystem   https://www.stm32duino.com    |
+-----------------------------------------------------------------------+

> Searching for [1209:BEBA] device...
##########
Error - [1209:BEBA] device is not found :(> Finish

[wandersoulz]

Are there board settings, jumper switch arrangements, or anything else that needs to be done before the flashing will work?

[jaysuk]

Nothing as far as I'm aware. I'll have to speak to flymaker tomorrow and get back to you. Those commands were given to me by him

On Wed, 21 Dec 2022, 20:02 wandersoulz, @.***> wrote:

Are there board settings, jumper switch arrangements, or anything else that needs to be done before the flashing will work?

— Reply to this email directly, view it on GitHub https://github.com/Mellow-3D/Fly-Gemini-V3/issues/1#issuecomment-1362027277, or unsubscribe https://github.com/notifications/unsubscribe-auth/AATUSBXQTXB6KA2YEOBHUOLWONO57ANCNFSM6AAAAAATFZ6G7M . You are receiving this because you commented.Message ID: @.***>

[jaysuk]

please see the updated instructions here https://mellow.klipper.cn/#/board/fly_gemini_v3/flash

[roster210]

can you guys post the correct pinout? this does not have the endstop configuration the same also. what else is different?

[jaysuk]

removed the image so just the schematic available