search

MonkWho / pfatt

Enable true bridge mode for AT&T U-Verse and pfSense (this is a fork of an original repository https://github.com/aus/pfatt. Since it is not available anymore, I'll do my best to maintain a copy for people that still need a bypass)
438 stars 170 forks source link

ngeth0 interface unavailable on reboot after 21.02 upgrade #50

Closed aholmes55 closed 3 years ago

aholmes55 commented 3 years ago

I recently upgraded from 2.4.5p1 to 21.02p1 on my Netgate SG-4860. The configuration is unable to find my netgraph bridge for the WAN connection and runs the interface assignment option where I can select ngeth0 for the WAN and everything works. I have to do this every reboot. Appreciate any help

`Initializing.................... done. Starting device manager (devd)...done. Loading configuration......done. ngeth0: link state changed to UP igb2: permanently promiscuous mode enabled igb1: permanently promiscuous mode enabled Updating configuration...done. Warning: Configuration references interfaces that do not exist: ngeth0

Network interface mismatch -- Running interface assignment option.

Valid interfaces are:

igb0 00:08:a2:0f:df:db (down) Intel(R) PRO/1000 PCI-Express Network Driver igb1 00:08:a2:0f:df:dc (down) Intel(R) PRO/1000 PCI-Express Network Driver igb2 00:08:a2:0f:df:d7 (down) Intel(R) PRO/1000 PCI-Express Network Driver igb3 00:08:a2:0f:df:d8 (down) Intel(R) PRO/1000 PCI-Express Network Driver igb4 00:08:a2:0f:df:d9 (down) Intel(R) PRO/1000 PCI-Express Network Driver igb5 00:08:a2:0f:df:da (down) Intel(R) PRO/1000 PCI-Express Network Driver ngeth0 dc:7f:a4:XX:XX:XX (up)

Do VLANs need to be set up first? If VLANs will not be used, or only for optional interfaces, it is typical to say no here and use the webConfigurator to configure VLANs later, if required.

Should VLANs be set up now [y|n]? igb2: link state changed to UP igb1: link state changed to UP igb0: link state changed to UP

If the names of the interfaces are not known, auto-detection can be used instead. To use auto-detection, please disconnect all interfaces before pressing 'a' to begin the process.

Enter the WAN interface name or 'a' for auto-detection (igb0 igb1 igb2 igb3 igb4 igb5 ngeth0 or a): ngeth0

Enter the LAN interface name or 'a' for auto-detection NOTE: this enables full Firewalling/NAT mode. (igb0 igb1 igb2 igb3 igb4 igb5 a or nothing if finished): igb0

Optional interface 1 description found: OPT1 Enter the Optional 1 interface name or 'a' for auto-detection (igb1 igb2 igb3 igb4 igb5 a or nothing if finished): igb2

Optional interface 2 description found: OPT2 Enter the Optional 2 interface name or 'a' for auto-detection (igb1 igb3 igb4 igb5 a or nothing if finished): igb3

Optional interface 3 description found: OPT3 Enter the Optional 3 interface name or 'a' for auto-detection (igb1 igb4 igb5 a or nothing if finished): igb4

Optional interface 4 description found: OPT4 Enter the Optional 4 interface name or 'a' for auto-detection (igb1 igb5 a or nothing if finished): igb5

Enter the Optional 5 interface name or 'a' for auto-detection (igb1 a or nothing if finished):

The interfaces will be assigned as follows:

WAN -> ngeth0 LAN -> igb0 OPT1 -> igb2 OPT2 -> igb3 OPT3 -> igb4 OPT4 -> igb5

Do you want to proceed [y|n]? y

Writing configuration.....................................................................................................done. One moment while the settings are reloading... done! ..Configuring looplo0: link state changed to UP back interface...done. Creating wireless clone interfaces...done. Configuring LAGG interfaces...done. Configuring VLAN interfaces...done. Configuring QinQ interfaces...done. Configuring IPsec VTI interfaces...done. Configuring WAN interface...done. Configuring LAN interface...igb0: link state changed to DOWN done. bridge0: Ethernet address: 58:9c:fc:XX:XX:XX igb0: promiscuous mode enabled bridge0: link state changed to UP Checking config backups consistency...done. Setting up extended sysctls...done. coretemp0: on cpu0 Setting timezone...done. 2021-03-06T06:53:59.807445-06:00 router.XXXXXX.XXX php-fpm 351 - - /rc.newwanip: rc.newwanip: Info: starting on ngeth0.

2021-03-06T06:53:59.808827-06:00 router.XXXXXX.XXX php-fpm 351 - - /rc.newwanip: rc.newwanip: on (IP address: 69.XXX.XXX.XXX) (interface: WAN[wan]) (real interface: ngeth0). `

aholmes55 commented 3 years ago

I solved this by adding netgh to the ignored interfaces in /etc/inc/util.inc at Line number 2385. Add ^ngeth| to the list of interfaces.

https://github.com/pfsense/pfsense/blob/RELENG_2_5_0/src/etc/inc/util.inc#L2385