GK7205V300 asking for u-boot password

[nkajic]

Board info: GK7205V300 + Smartsens SC5239P https://vi.aliexpress.com/item/1005003340814126.html

Tried but without success HI2105CHIP ubootpwd

Normal boot

System startup

Uncompress Ok!

U-Boot 2016.11-g4bd9c94-dirty (Apr 22 2022 - 21:25:43 +0800)gk7205v300

Relocation Offset is: 0771f000
Relocating to 47f1f000, new gd at 47edeef0, sp at 47edeed0
SPI Nor:  Check Flash Memory Controller v100 ... Found
SPI Nor ID Table Version 1.0
@hifmc_spi_nor_probe(), SPI Nor(cs 0) ID: 0xa1 0x40 0x18 <Read>
@hifmc_spi_nor_probe(), SPI Nor(cs 0) ID: 0xa1 0x40 0x18 <Found>
SPI Nor(cs 0) ID: 0xa1 0x40 0x18
eFlashType: 30.
@XmSpiNor_initSr3() need No SR3!
@XmSpiNor_printWps(), WPS Enabled!
Flash Name: XM_FM25Q128A{0xA14018), 0x1000000.
@hifmc_spi_nor_probe(), XmSpiNor_ProtMgr_probe(): OK.
@XmSpiNor_enableQuadMode(), Quad was Disabled, SRx: [2, 0x8].
Block:64KB Chip:16MB Name:"XM_FM25Q128A"
CONFIG_CLOSE_SPI_8PIN_4IO = y.
read->iftype[0: STD, 1: DUAL, 2: DIO, 3: QUAD, 4: QIO]: 1.
lk[7 => 0x1000000], Total Lock Blks: 286 <WPS=1>
SRx val: {[1, 0x20], [1, 0x8], [1, 0x0], [0, 0x0]}, SrVal: 0x700000000000820.
SPI Nor total size: 16MB
In:    serial
Out:   serial
Err:   serial
Net:   eth0
autoboot:  0 
@do_spi_flash_probe() flash->erase_size: 65536, flash->sector_size: 0
device 0 offset 0x40000, size 0x540000

SF: 5505024 bytes @ 0x40000 Read: OK
srcAddr: 0x43000000, dstAddr: 0x42000000, filename: boot/uImage.
created_inode 0x47edfc18
find_squashfs_file: name bin, start_block 0, offset 1824, type 1
find_squashfs_file: name boot, start_block 0, offset 1996, type 1
read inode: name boot, sb 0, of 1996, type 1
find_squashfs_file: name uImage, start_block 0, offset 1856, type 2
read inode: name uImage, sb 0, of 1856, type 2
write_file: regular file, blocks 27
len 1723581
### get_squashfs_file OK: loade 1723581 bytes to 0x42000000
## Booting kernel from Legacy Image at 42000000 ...
   Image Name:   Linux-4.9.37
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1723517 Bytes = 1.6 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Loading Kernel Image ... OK
using: ATAGS
at setup_xminfo_tag() g_nXmBootSysIndex: 0, g_nXmRomfsIndex: 0.

Starting kernel ...

CTL + C break boot asking password

System startup

Uncompress Ok!

U-Boot 2016.11-g4bd9c94-dirty (Apr 22 2022 - 21:25:43 +0800)gk7205v300

Relocation Offset is: 0771f000
Relocating to 47f1f000, new gd at 47edeef0, sp at 47edeed0
SPI Nor:  Check Flash Memory Controller v100 ... Found
SPI Nor ID Table Version 1.0
@hifmc_spi_nor_probe(), SPI Nor(cs 0) ID: 0xa1 0x40 0x18 <Read>
@hifmc_spi_nor_probe(), SPI Nor(cs 0) ID: 0xa1 0x40 0x18 <Found>
SPI Nor(cs 0) ID: 0xa1 0x40 0x18
eFlashType: 30.
@XmSpiNor_initSr3() need No SR3!
@XmSpiNor_printWps(), WPS Enabled!
Flash Name: XM_FM25Q128A{0xA14018), 0x1000000.
@hifmc_spi_nor_probe(), XmSpiNor_ProtMgr_probe(): OK.
@XmSpiNor_enableQuadMode(), Quad was Disabled, SRx: [2, 0x8].
Block:64KB Chip:16MB Name:"XM_FM25Q128A"
CONFIG_CLOSE_SPI_8PIN_4IO = y.
read->iftype[0: STD, 1: DUAL, 2: DIO, 3: QUAD, 4: QIO]: 1.
lk[7 => 0x1000000], Total Lock Blks: 286 <WPS=1>
SRx val: {[1, 0x20], [1, 0x8], [1, 0x0], [0, 0x0]}, SrVal: 0x700000000000820.
SPI Nor total size: 16MB
In:    serial
Out:   serial
Err:   serial
Net:   eth0
autoboot:  0 
Password: 
Password: 
Password: 
Password: 

Thanks

[Grundefuht]

I met same problem. But found that no u-boot is needed

1. upgraded camera via web interface by precompiled "lite" bin.
2. setup image sensor properly. I selected "4l_sc223a_i2c_1080p"

i missed creating first backup, that is not good. but i was lucky

[nkajic]

Hi @Grundefuht that is interesting. Thanks for feedback. I will keep issue open until someone finds pwd.

[ankurvdev]

Try this #Ux6@9V&4_Rz