search

PX4 / PX4-Autopilot

PX4 Autopilot Software
https://px4.io
BSD 3-Clause "New" or "Revised" License
8.5k stars 13.51k forks source link

unable to start mission : vehicle not ready #11986

Closed sampathkumarch closed 5 years ago

sampathkumarch commented 5 years ago

https://discuss.px4.io/t/unable-to-start-mission-vehicle-not-ready/10896

sampathkumarch commented 5 years ago

Sir I have these components

1.pixhawk 2.gps module 3.power management board 4.lipo battery

  1. One ESC 6.one brush less motor

  2. Q ground control software

    I don't have these comments

1.s.bus transmitter and receiver 2.telemetry system

  1. Air speed sensor

Wiring connection: throttle pin is given IO port 4 pin Right elevator is given IO port 2 pin Left elevator is given IO port 1pin

Frame : FIXED FLYING WING

I followed these steps

1.upload firmware 2.frame selected ( generic flying wing) 3.calibrate all sensors but air speed sensor is not calibrate so using circuit breaker disabled this 4.power calibration completed 5 safety calibrated

I do not have a receiver and transmitter so I can run in autopilot so COM_RC_IN_MODE was desiabled.then after you say it NAV_RC_ACT is set 0 . Am using USB cable for connectivity computer to pixhawk so that one also disabled using circuit breaker. Then after you say battery checks also disabled by using circuit breaker. Then after I given a mission plane and upload it then show the one message is start the mission.then after I start the mission getting one more message is unable to start mission .vehicle not ready .please resolve my problem sir. please help me sir

On Wed, May 8, 2019, 12:57 PM Julian Oes notifications@github.com wrote:

Closed #11986 https://github.com/PX4/Firmware/issues/11986.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#event-2326385307, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQY64N4IT46Y2Z7GPBLPUJ6E3ANCNFSM4HLPBJNQ .

On Wed, May 8, 2019, 12:57 PM Julian Oes notifications@github.com wrote:

Closed #11986 https://github.com/PX4/Firmware/issues/11986.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#event-2326385307, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQY64N4IT46Y2Z7GPBLPUJ6E3ANCNFSM4HLPBJNQ .

sampathkumarch commented 5 years ago

sir please help me . why not given to me reply tell me sir

On Wed, May 8, 2019 at 5:05 PM Sampath kumar Chiruthoti < sampathkumarchiruthoti@gmail.com> wrote:

Sir I have these components

1.pixhawk 2.gps module 3.power management board 4.lipo battery

  1. One ESC 6.one brush less motor

  2. Q ground control software

    I don't have these comments

1.s.bus transmitter and receiver 2.telemetry system

  1. Air speed sensor

Wiring connection: throttle pin is given IO port 4 pin Right elevator is given IO port 2 pin Left elevator is given IO port 1pin

Frame : FIXED FLYING WING

I followed these steps

1.upload firmware 2.frame selected ( generic flying wing) 3.calibrate all sensors but air speed sensor is not calibrate so using circuit breaker disabled this 4.power calibration completed 5 safety calibrated

I do not have a receiver and transmitter so I can run in autopilot so COM_RC_IN_MODE was desiabled.then after you say it NAV_RC_ACT is set 0 . Am using USB cable for connectivity computer to pixhawk so that one also disabled using circuit breaker. Then after you say battery checks also disabled by using circuit breaker. Then after I given a mission plane and upload it then show the one message is start the mission.then after I start the mission getting one more message is unable to start mission .vehicle not ready .please resolve my problem sir. please help me sir

On Wed, May 8, 2019, 12:57 PM Julian Oes notifications@github.com wrote:

Closed #11986 https://github.com/PX4/Firmware/issues/11986.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#event-2326385307, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQY64N4IT46Y2Z7GPBLPUJ6E3ANCNFSM4HLPBJNQ .

On Wed, May 8, 2019, 12:57 PM Julian Oes notifications@github.com wrote:

Closed #11986 https://github.com/PX4/Firmware/issues/11986.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#event-2326385307, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQY64N4IT46Y2Z7GPBLPUJ6E3ANCNFSM4HLPBJNQ .

hamishwillee commented 5 years ago

@sampathkumarch

why not given to me reply tell me sir

The issue was closed because this is a place for bug reports and feature requests - is not a place for you to post support requests. You have correctly created a discussion board post. Additional information and questions should go in that post.

sampathkumarch commented 5 years ago

Thank you for your response, but where is the discussion this issue iam post for it

On Fri, May 10, 2019, 4:00 AM Hamish Willee notifications@github.com wrote:

@sampathkumarch https://github.com/sampathkumarch

why not given to me reply tell me sir

The issue was closed because this is a place for bug reports and feature requests - is not a place for you to post support requests. You have correctly created a discussion board issue. Additional information and questions should go in that issue.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#issuecomment-491090859, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQ2GZZNKQCZXF35U6ETPUSQXBANCNFSM4HLPBJNQ .

hamishwillee commented 5 years ago

Pardon? In your top post https://github.com/PX4/Firmware/issues/11986#issue-441587312 - see https://discuss.px4.io/t/unable-to-start-mission-vehicle-not-ready/10896

hamishwillee commented 5 years ago

If that isn't your post, then please create a new one. We can't help you in the defect tracker.

sampathkumarch commented 5 years ago

Ok sir .what do I do now?

On Fri, May 10, 2019, 8:18 AM Hamish Willee notifications@github.com wrote:

If that isn't your post, then please create a new one. We can't help you in the defect tracker.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#issuecomment-491135744, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQY4WK6J5R33NKGRVTTPUTPAFANCNFSM4HLPBJNQ .

sampathkumarch commented 5 years ago

Ok sir, what I do now

On Fri, May 10, 2019, 8:31 AM Sampath kumar Chiruthoti < sampathkumarchiruthoti@gmail.com> wrote:

Ok sir .what do I do now?

On Fri, May 10, 2019, 8:18 AM Hamish Willee notifications@github.com wrote:

If that isn't your post, then please create a new one. We can't help you in the defect tracker.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/PX4/Firmware/issues/11986#issuecomment-491135744, or mute the thread https://github.com/notifications/unsubscribe-auth/AL6WXQY4WK6J5R33NKGRVTTPUTPAFANCNFSM4HLPBJNQ .

hamishwillee commented 5 years ago

Create a post in https://discuss.px4.io with all the details of your setup - vehicle, flight controller, autopilot, autopilot version, ground station, what you have tried. Everything you can think of that might be relevant to the problem.

hamishwillee commented 5 years ago

The information you have put in this issue looks good, but it can't be posted here, because this is for bugs, and at the moment all we know is that you have a problem. That might be due to your setup or something else.