Android Ascet-configurator Translation

[ghost]

Hi, id used the Ascet-configurator (Android) today. Please please translate it in English Oo! And some things are displayed wrong on my phone.

[ghost]

Id started the translation already, but what means: Скрыть служебные поля Считать настройки

Please correct me if im wrong, im trying to write down, what id understood.

---------------First Tab---------------------------------- Parrameter - Value - type - Team - Enemy Team - Min value - Max value ?!?!?!?!?!?! :boom: What does the 1, 5. and 6t parameter mean ? For me my translation makes no sense.

In the button under the list i can say (Read values) and (Writes values into the device) And in the checkbox in the first tab, i can tell the weapon (Team OFF) or (Team ON).

--------------second tab-------------------------------- Set the protocol. Useful to work for other Lasertag system. Apply Protocoll - Save - Open - Read from device

--------------third tab----------------------- EEPROM

Save to EEPROM - Read from EEPROM There i can set things in the EEPROM

--------------fourth tab------------------ X. Filename - Open - Play Set Sounds and play them Write to EEPROM ---->I did not understand the last button<----

-------------fifth tab-------------------- Remote

I was not be able to translate it.... There is a New Game button. If i press a button, sth comes up, but what can i enter there ? There is a drop down list, with nothing inside....

------------The about tab----------- Completly translated.

[ghost]

What is the baudrate to talk to the weapon ? I got a message "Ascet 3.1 @ 9600 baud" and nothing more.... If i enter for example team_id?, id got nothing.

Can i configure what baudrate is used ? Can i configure if a bluetooth bandana is used (Master/Slave) ? Do i have to configure if keys are used ? Were can i define if i want to use a display or not ?

Thanks in advance

[PingvinOpenTag]

Well, I'll transfer. Module using the remote control is not implemented.

To read the settings from a device in the "Protocol" ("Протокол") you have to press the button "Read from the device" ("Считать из устройства") https://www.youtube.com/watch?v=n5ikXYz3mhE

[PingvinOpenTag]

Bandana - Master Tag - Slave Bluetooth modules are configured using the AT-commands http://armada.ltascet.com/images/hc-05.pdf http://armada.ltascet.com/index.php/ru/tekhnologii-v-menu/asket/moduli-rasshireniya-dlya-asketa/blyutus-modul/nastrojka-bluetooth-modulej

AT+NAME=Bandana01 AT+ROLE=1 (Master) AT+CMODE=0 (connect fixed address) AT+BIND= xxxx, xx, xxxxxx (mac-address of you Tag bluetooth module) AT+PSWD=xxxx (PIN code)

[PingvinOpenTag]

I recommend to the bandana PCB powered from 3V. Then bluetooth shield is not needed. http://www.youtube.com/watch?v=OKqPU76Skjw When setting up using the AT-commands then also need to supply power 3V (not 5V)

I got a good idea! If you use the power supply in the 3-3.6, we can connect to the Bluetooth module a few control signals - RESET and switch to AT commands. Free port on board a lot! And then you can configure the module from firmware. A switching "Master" / "slave" to connect to the input fire mode switch.

[PingvinOpenTag]

Configurator will rewrite on QML (change the interface). Qt widgets not useful on small screens of mobile devices.

[ghost]

Ok, now im confused, to get it run, what i have to do ? I have two setuped weapons. Cant you add a config.h file where im able to define if a bluetooth module, LCD e.t.c is connected or not ?

I do not understand how i do change the firmware. Id hoped that im able to do that in the configurator.... I just want a gun with wired head sensor .... I just want to play :cry:

(Did you check the new part list ? Can´t await to build more of two)

[PingvinOpenTag]

Nothing needs to be configured. Everything works so. If you do not need the LCD or Bluetooth - simply do not connect them to the board.

If you want to play only with a wired bandana - through a resistor 10K to the connecting pin "Status" (pin 2 on connector for Bluetooth Module) to the ground, otherwise the system will not work against cheating.

Initially firmware (or bootloader) can upload with the help of SPI programmer. Be very careful with setting FUSES!!!

Programmers are different. The easiest - it's "LPT 5 wires" http://armada.ltascet.com/index.php/ru/proshivka/kak-i-chem-proshit-asketa

I recommend using the USB programmers. For example USBASP USBISP AVR Programmer http://dvrobot.ru/var/cache/images/product/45/00/4500628ad509cd073e987c6ba312fd40-324.jpg http://dvrobot.ru/237/213.html The program is to work with this programmer. http://yourdevice.net/proekty/avrdude-prog

Drivers http://www.yourdevice.net/downloads/usbavr.rar

Subject extensive, I recommend to you before programming device, available on the respective resources, how to program the AVR for SPI And at first practice on the breadboard. Because if you are, for example, incorrectly configured FUSE - programmer can no longer connect to the controller.

There project resource http://armada.ltascet.com Website multilingual. There is a German branch http://armada.ltascet.com/index.php/de/ Help me to fill it with content and translate.

Here and there a forum.

[ghost]

Ok, can you resend me the login details ? My new e-mail address is justus (at) strongforce (DOT).de my old still exists and i also read from this mail.

Thanks in advance.

[PingvinOpenTag]

Check Mail