search

Protocentral / protocentral-healthypi-v3

HealthyPi is the first fully open-source, full-featured vital sign monitor. Using the Raspberry Pi as its computing and display platform, the HealthyPi add-on HAT turns the Raspberry Pi into a vital sign monitoring system.
http://healthypi.protocentral.com
Other
194 stars 51 forks source link

Usless after firmware update. #6

Closed thejarle closed 5 years ago

thejarle commented 6 years ago

Hello. I did a firmware upgrade (1.1) a while ago, and since then my helthypi3 has been useless. I have tried reinstalling the software on my pi (I got the v3 complete kit!), setting up a second pi with a fresh install and installed the heltypi software from scratch, tryd to get it working on both windows and Debian pc's with usb, but I get nothing. The firmware update was painless and everything looked fine. (I have done it twice to make sure) But since than I have not seen any info coming from my helthypi v3. Any help would be appreciated as I have tried everything I can think of.

VenkateshBhat commented 6 years ago

@thejarle sorry for the inconvinience caused, could you please connect the HealthyPi board to the PC through USB port and check whether the USB is enumerating?

thejarle commented 6 years ago

​

Mvh Jarle Hansen

On Sun, Nov 12, 2017 at 4:20 AM, Venkatesh Bhat notifications@github.com wrote:

@thejarle https://github.com/thejarle sorry for the inconvinience caused, could you please connect the HealthyPi board to the PC through USB port and check whether the USB is enumerating?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-343710589, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrOYGZWy7K_LvB5NUcnHmUJ9bAr9Tks5s1mQYgaJpZM4QashU .

VenkateshBhat commented 6 years ago

Sorry I did not understand , please elaborate on this.

thejarle commented 6 years ago

When I connect the Healthypi to the pc it shows like this in device manager. Yes, I guess it "enumerates" (what ever that means?)

BR Jarle

Mvh Jarle Hansen

On Mon, Nov 13, 2017 at 2:06 PM, Venkatesh Bhat notifications@github.com wrote:

Sorry I did not understand , please elaborate on this.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-343913178, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrJG4lQzbfneqoPliiUJ_hS8q7i4_ks5s2D7OgaJpZM4QashU .

VenkateshBhat commented 6 years ago

Could you please attach the screenshot ?

thejarle commented 6 years ago

Yes, here you are.

Jarle

Mvh Jarle Hansen

On Mon, Nov 13, 2017 at 2:25 PM, Venkatesh Bhat notifications@github.com wrote:

Could you please attach the screenshot ?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-343918009, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrGVl1bOxaSbAZy8Cbe_DBo36G-O5ks5s2ENggaJpZM4QashU .

thejarle commented 6 years ago

Hello again. Any idea . As I said: I have reinstalled my healthypi and installed the software from scratch, but nothing works....

Jarle

On Mon, Nov 13, 2017 at 2:25 PM Venkatesh Bhat notifications@github.com wrote:

Could you please attach the screenshot ?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-343918009, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrGVl1bOxaSbAZy8Cbe_DBo36G-O5ks5s2ENggaJpZM4QashU .

-- Mvh Jarle Hansen

VenkateshBhat commented 6 years ago

@thejarle , I just want to ensure the USB port is enumerating, it would be helpful if you can share the screen shot of device manager page.

thejarle commented 6 years ago

Yes, I have done it two times all ready ! Here it is one more time It is attached as a file called capture1.jpg. If you somehow dont see it this time either it sais: Arduino Zero (com 2) when I connect it. I have tryeed setting it to different com ports. It was at com 16 in the beginning.

Jarle

tor. 16. nov. 2017 kl. 06:16 skrev Venkatesh Bhat <notifications@github.com

:

@thejarle https://github.com/thejarle , I just want to ensure the USB port is enumerating, it would be helpful if you can share the screen shot of device manager page.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-344818401, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrFv8ttpDNFmrH--pRFR1vrHvGVLpks5s28UngaJpZM4QashU .

VenkateshBhat commented 6 years ago

I still could not able to see, that is fine. I presume that you are able to upload the program, could you please check in the serial monitor that data's are coming(HEX)?

thejarle commented 6 years ago

I assume you are talking about the serial monitor in arduino ? I have never used that. Can you please give me some instructions ?

Jarle

Mvh Jarle Hansen

On Thu, Nov 16, 2017 at 10:23 AM, Venkatesh Bhat notifications@github.com wrote:

I still could not able to see, that is fine. I presume that you are able to upload the program, could you please check in the serial monitor that data's are coming(HEX)?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-344863818, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrKHi9mTnkVfyhEqycwDC_QPrGk8kks5s2_8SgaJpZM4QashU .

thejarle commented 6 years ago

I tryed to reflash the firmware again and everything looks ok when I do:

Sketch uses 25,708 bytes (9%) of program storage space. Maximum is 262,144 bytes. Atmel SMART device 0x10010005 found Device : ATSAMD21G18A Chip ID : 10010005 Version : v2.0 [Arduino:XYZ] Dec 20 2016 15:36:39 Address : 8192 Pages : 3968 Page Size : 64 bytes Total Size : 248KB Planes : 1 Lock Regions : 16 Locked : none Security : false Boot Flash : true BOD : true BOR : true Arduino : FAST_CHIP_ERASE Arduino : FAST_MULTI_PAGE_WRITE Arduino : CAN_CHECKSUM_MEMORY_BUFFER Erase flash done in 0.663 seconds

Write 26636 bytes to flash (417 pages)

[==== ] 15% (64/417 pages) [========= ] 30% (128/417 pages) [============= ] 46% (192/417 pages) [================== ] 61% (256/417 pages) [======================= ] 76% (320/417 pages) [=========================== ] 92% (384/417 pages) [==============================] 100% (417/417 pages) done in 0.167 seconds

Verify 26636 bytes of flash with checksum. Verify successful done in 0.027 seconds CPU reset.

Mvh Jarle Hansen

On Thu, Nov 16, 2017 at 12:25 PM, Jarle Hansen thejarle@gmail.com wrote:

I assume you are talking about the serial monitor in arduino ? I have never used that. Can you please give me some instructions ?

Jarle

Mvh Jarle Hansen

On Thu, Nov 16, 2017 at 10:23 AM, Venkatesh Bhat <notifications@github.com

wrote:

I still could not able to see, that is fine. I presume that you are able to upload the program, could you please check in the serial monitor that data's are coming(HEX)?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-344863818, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrKHi9mTnkVfyhEqycwDC_QPrGk8kks5s2_8SgaJpZM4QashU .

VenkateshBhat commented 6 years ago

Please share your mail id.

thejarle commented 6 years ago

Share my Mail id ? What do you mean? What Mail ID ?

Jarle

fre. 17. nov. 2017 kl. 08:24 skrev Venkatesh Bhat <notifications@github.com

:

Please share your mail id.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-345165971, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrOc_pjPDO7zM_PtsHlIlQRvm6bQtks5s3TS9gaJpZM4QashU .

-- Mvh Jarle Hansen

thejarle commented 6 years ago

Do you mean the ID I usedvanlig when ordering the healtypy ? If that is what you mean i think it was: jarle@theearl.net

Jarle

fre. 17. nov. 2017 kl. 08:24 skrev Venkatesh Bhat <notifications@github.com

:

Please share your mail id.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-345165971, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrOc_pjPDO7zM_PtsHlIlQRvm6bQtks5s3TS9gaJpZM4QashU .

-- Mvh Jarle Hansen

VenkateshBhat commented 6 years ago

Your e-mail iD, I could able to see your attachment here.

thejarle commented 6 years ago

you can use jarle@theearl.net or thejarle@gmail.com

Jarle

Mvh Jarle Hansen

On Fri, Nov 17, 2017 at 9:18 AM, Venkatesh Bhat notifications@github.com wrote:

Your e-mail iD, I could able to see your attachment here.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/Protocentral/protocentral-healthypi-v3/issues/6#issuecomment-345175550, or mute the thread https://github.com/notifications/unsubscribe-auth/AITbrFdlhJ66lh4ls9m9qNt58ofRjOfDks5s3UFGgaJpZM4QashU .