issues
search
PyCubed-Mini
/
avionics-mainboard
Main flight computer for the PyCubed-Mini PocketQube platform
3
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
B3/03 updates
#34
NeilKhera
closed
1 year ago
0
Replace reset button (again)
#33
NeilKhera
closed
1 year ago
1
Re-add Fiducials to both sides
#32
NeilKhera
closed
1 year ago
1
Remove inner plating from mechanical holes
#31
NeilKhera
opened
1 year ago
0
Connect IMU INT and RST lines to MCU
#30
NeilKhera
closed
1 year ago
1
B3/01 updates
#29
NeilKhera
closed
1 year ago
0
reduce board corners by 0.1mm on each side
#28
jbwillis
closed
1 year ago
0
Make Neopixel more visible in full assembly
#27
jbwillis
closed
1 year ago
0
Add USB LiPo Charge Circuit?
#26
NeilKhera
opened
1 year ago
1
Make watchdog enable-able or select different watchdog component
#25
NeilKhera
closed
1 year ago
0
B2/01 updates
#24
NeilKhera
closed
1 year ago
0
Firmware version cleanup
#23
jbwillis
closed
1 year ago
0
Payload Interface
#22
jbwillis
closed
1 year ago
0
More descriptive names than U9
#21
thetazero
closed
1 year ago
0
Cutout for antenna cable
#20
jbwillis
closed
2 years ago
0
Revision B/03 Updates
#19
NeilKhera
closed
2 years ago
0
Add Real Time Clock
#18
jbwillis
closed
2 years ago
0
Change resistor divider to HI_POW rather than BATT_P
#17
jbwillis
closed
2 years ago
0
Burnwire Pin Updates
#16
yashika-batra
closed
2 years ago
2
Replace X/Z solar connectors with CLP-105-02-F-DH-A
#15
jbwillis
closed
2 years ago
0
Label Solar Board connectors
#14
jbwillis
closed
1 year ago
0
Make JTAG header accessible by only removing one solar board
#13
jbwillis
opened
2 years ago
1
Find new motor drivers
#12
jbwillis
closed
2 years ago
1
Reset button accessible from outside satellite
#11
jbwillis
closed
1 year ago
1
v04.1 Changes
#10
NeilKhera
closed
2 years ago
0
I2C 3 to solar boards
#9
jbwillis
closed
2 years ago
0
Test Burnwire circuit with PWM gate control, and switch BURN1 to a MCU pin with PWM support
#8
NeilKhera
closed
2 years ago
0
Firmware config documentation for ATSAMD51J19A / 20A
#7
NeilKhera
closed
2 years ago
0
Mainboard v03 Stack Updates
#6
NeilKhera
closed
2 years ago
5
Create BOM and check for parts availability
#5
jbwillis
closed
2 years ago
0
Change RBF pin to 1x6 header
#4
jbwillis
closed
2 years ago
0
Neil updates
#3
jbwillis
closed
2 years ago
14
Load firmware onto current mainboard rev and run tests
#2
jbwillis
closed
2 years ago
2
Replace camera FFC with 1.27mm stacking header
#1
jbwillis
closed
2 years ago
0