[EOT](ERROR)
执行命令失败，可能的原因如下：
1.请检查当前单板Flash与烧写分区中的Flash类型是否一致；
2.当前fastboot不支持该命令；
Failed to get bad block info.
Failed to get Chip size
串口已经连接，请给单板上电，若已经上电，请断电后重新上电。
# ---- 50%
# ---- 100%
Boot download completed!
Starting fastboot ...
System startup
DDRS
Reg Version: v1.1.0
Reg Time: 2015/5/5 17:31:59
Reg Name: hi3796mdmo1a_hi3796mv100_ddr3_1gbyte_16bitx2_4layers_emmc.reg
Jump to DDR
Fastboot 3.3.0 (@f7707a192e32) (Mar 28 2019 - 08:08:55)
Fastboot: Version 3.3.0
Build Date: Mar 28 2019, 08:09:38
CPU: Hi3796Mv100
Boot Media: eMMC
DDR Size: 1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
MMC/SD controller initialization.
MMC/SD Card:
MID: 0x45
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "SEM08"
Chip Type: MMC
Version: 4.5
Speed: 52000000Hz
Bus Width: 8bit
Boot Addr: 0 Bytes
Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
start download process.
Boot started successfully!
Send command: setenv serverip 192.168.2.1
[EOT](OK)
Send command: setenv ethaddr 52:ED:44:B1:84:8E
[EOT](OK)
Send command: setenv ipaddr 192.168.2.11
[EOT](OK)
Send command: setenv netmask 255.255.255.0
[EOT](OK)
Send command: setenv gatewayip 192.168.2.1
[EOT](OK)
Send command: mmc read 0 0x1000000 0x54000 0x10000
MMC read: dev # 0, block # 344064, count 65536 ... 65536 blocks read: OK
82869546 Bytes/s
[EOT](OK)
Tftp server Download Home switched to <C:\test\hdc6910\stb>
Send command: tftp 0x1000000 kernel.bin.part0 0x2000000
Eth up port phy at 0x01 is connect
Eth down port phy at 0x1f is connect
Hisilicon ETH net controler
MAC: 52-ED-44-B1-84-8E
UP_PORT : phy status change : LINK=UP : DUPLEX=FULL : SPEED=100M
TFTP to server 192.168.2.1; our IP address is 192.168.2.11
Upload Filename 'kernel.bin.part0'.
Upload from address: 0x1000000, 32.000 MB to be send ...
Uploading: *# [ Connected ]
####################T T T T T T
网络下载TFTP超时，可能的原因如下：
1.首先检查服务器IP是否正确，若不正确点击重新加载，加载最新的PC端IP地址；
2.检查子网掩码与网关是否配置正确;
3.检查板端IP地址是否被占用（使用ping命令，查看当前设置板端IP是否能够ping通，若不能则表示当前网络未被占用）将以上参数全部保证正确后再尝试重新烧写。
4.检查PC上是否有TFTP服务器占用当前69端口。
5.检查Fastboot中网络驱动部分是否正确；
6.打开工具菜单栏上的窗口->首选项->HiBurn->TFTP设置，关闭勾选TFTP加速，然后再进行烧写；
7.使用外部的TFTP32工具进行烧写，打开TFTP32工具设置好镜像路径和服务器IP后，重新烧写。
Resend command...
Send command: tftp 0x1000000 kernel.bin.part0 0x2000000
Eth up port phy at 0x01 is connect
Eth down port phy at 0x1f is connect
Hisilicon ETH net controler
miiphy_register: non unique device name '0:1'
miiphy_register: non unique device name '0:31'
MAC: 52-ED-44-B1-84-8E
UP_PORT : phy status change : LINK=DOWN : DUPLEX=HALF : SPEED=100M
UP_PORT : phy status change : LINK=UP : DUPLEX=HALF : SPEED=100M
TFTP to server 192.168.2.1; our IP address is 192.168.2.11
Upload Filename 'kernel.bin.part0'.
Upload from address: 0x1000000, 32.000 MB to be send ...
Uploading: *T T T T T T T T T T T T
QGB
commented
1 year ago