[x] bloom_bytes OK but don't know if the output is right:
INFO # checking 10000 elements took 2145ms
INFO #
INFO # 267 elements probably in the filter.
INFO # 9733 elements not in the filter.
INFO # false positive rate.
INFO #
INFO # All done!
[ ] coap
[ ] conn_ip
[x] cpp11_condition_variable OK
[ ] cpp11_mutex
[x] cpp11_thread OK
[ ] driver_adt7310
[ ] driver_at30tse75x
[x] driver_at86rf2xx OK
[ ] driver_bh1750
[x] driver_bmp180 OK Results in error as expected
[ ] driver_dht
[ ] driver_enc28j60
[ ] driver_encx24j600
[x] driver_hdc1000 OK Results in error as expected
[ ] driver_hih6130
[ ] driver_ina220
[ ] driver_io1_xplained
[x] driver_isl29020 OK
[ ] driver_isl29125
[ ] driver_kw2xrf
[x] driver_l3g4200d OK
[ ] driver_lis3dh
[ ] driver_lis3mdl
[ ] driver_lpd8808
[x] driver_lps331ap OK
[ ] driver_lsm303dlhc
[ ] driver_mag3110
[x] driver_mma8652 OK Results in error as expected
[ ] driver_mpl3115a2
[ ] driver_mpu9150
[x] driver_mq3 OK Lectures are 0 since there's no sensor
[ ] driver_nrf24l01p_lowlevel
[ ] driver_nrfmin
[ ] driver_nvram_spi
[x] driver_pcd8544 OK Runs but no display to test
[ ] driver_pir
[ ] driver_servo
[x] driver_si70xx OK Results in error as expected
[ ] driver_srf02
[ ] driver_srf08
[x] driver_tcs37727 OK Results in error as expected
[ ] driver_tmp006
[ ] driver_xbee
[x] emb6 OK
[ ] fault_handler
[ ] float
[x] fmt_print OK
[ ] gnrc_ipv6_ext
[ ] gnrc_sixlowpan
[x] gnrc_sock_ip OK
[x] gnrc_sock_udp OK
[ ] irq
[ ] leds
[ ] libfixmath
[x] lwip OK
[ ] malloc
[ ] minimal
[x] mpu_stack_guard OK Shows failure because board is not whitelisted
[x] msg_send_receive OK
[ ] msg_try_receive
[ ] mutex_order
[x] mutex_unlock_and_sleep OK
[ ] netdev2_test
[ ] netstats_l2
[x] nhdp OK But build in OS X fails
[x] od OK
[ ] periph_adc
[ ] periph_cpuid
[x] periph_dac OK But periph_dac module is not provided for iotlab-m3
[ ] periph_gpio
[ ] periph_hwrng
[x] periph_i2c OK All drivers work as expected
[ ] periph_pwm
[ ] periph_rtc
[x] periph_rtt OK
[ ] periph_spi
[ ] periph_timer
[x] periph_uart OK
[ ] pipe
[x] pkg_aversiveplusplus OK But no servos attached to board
[ ] pkg_cmsis-dsp
[x] pkg_jsmn OK
[ ] pkg_micro-ecc
[x] pkg_tiny-asn1 OK
[ ] pkg_u8g2
[x] posix_semaphore OK
[ ] posix_sleep
[ ] pthread
[x] pthread_barrier OK
[ ] pthread_cleanup
[ ] pthread_condition_variable
[x] pthread_cooperation OK
[ ] pthread_rwlock
[ ] pthread_tls
[x] saul OK
[ ] sched_testing
[ ] shell
[x] sizeof_tcb OK
[ ] slip
[ ] struct_tm_utility
[x] thread_basic OK
[ ] thread_cooperation
[ ] thread_exit
[x] thread_flags OK
[ ] thread_flood
[ ] thread_msg
[x] thread_msg_avail OK
[ ] thread_msg_block_wo_queue
[ ] thread_msg_block_w_queue
[x] thread_msg_seq OK
[ ] warn_conflict
[ ] xtimer_drift
[x] xtimer_hang OK
[ ] xtimer_longterm
[ ] xtimer_msg
[x] xtimer_msg_receive_timeout OK
[ ] xtimer_now64_continuity
[x] xtimer_periodic_wakeup OK
[ ] xtimer_remove
[x] xtimer_reset OK
[ ] xtimer_shift_on_compare
[ ] zep
This list is based on previous #23 with different test marked for this release. I also added the new ones which are systematically performed.
Task # 02
Perform a subset of tests on
iotlab-m3
node:periph_dac
module is not provided for iotlab-m3This list is based on previous #23 with different test marked for this release. I also added the new ones which are systematically performed.