m4gn3to
commented
3 days ago Hi.
I've downloaded latest version and now, the wizard ends fine.
But there is a little mess with the configuration.
The first error is that it includes a temperature_sensor for the LPC and it says it's unsupported.
Then, I've checked none input shaper but there is an error about probe points in resonance_tester.
Then, there is a mess with the pins aliases, there lack the exp ones and when I added them, there is an error with every pin alias declared as "null".
I have it running with this pin config:
[board_pins skr_14_turbo_tmc2209] aliases:
steppers
x_step_pin=P2.2, x_dir_pin=P2.6, x_enable_pin=P2.1, x_uart_pin=P1.10, x_diag_pin=null, x_endstop_pin=P1.29, y_step_pin=P0.19, y_dir_pin=P0.20, y_enable_pin=P2.8, y_uart_pin=P1.9, y_diag_pin=null, y_endstop_pin=P1.28, z0_step_pin=P0.22, z0_dir_pin=P2.11, z0_enable_pin=P0.21, z0_uart_pin=P1.8, z0_diag_pin=null, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=P2.13, e_dir_pin=P0.11, e_enable_pin=P2.12, e_uart_pin=P1.4, e_diag_pin=null, e_heater_pin=P2.7, e_sensor_pin=P0.24,
accel
adxl345_cs_pin=null,
auto leveling
bltouch_sensor_pin=P0.10, bltouch_control_pin=P2.0, probe_pin=P0.10,
fans
fan_part_cooling_pin=P2.3, fan_toolhead_cooling_pin=P2.4, fan_controller_board_pin=null,
Bed heater
heater_bed_heating_pin=P2.5, heater_bed_sensor_pin=P0.25,
Expansion ports
EXP1 header
#################################################################
EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=,
#############################------##############################
EXP2 header
#################################################################
EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=, EXP2_10=,
EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=,
#############################------##############################
Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
display_rs_pin=P1.19, display_e_pin=P1.18, display_d4_pin=P1.20, display_d5_pin=P1.21, display_d6_pin=P1.22, display_d7_pin=P1.23, display_encoder_pin1=P3.26, display_encoder_pin2=P3.25, display_click_pin=P0.28, display_beeper_pin=P1.30,
filament_sensor
filament_switch_sensor_pin=P1.26,
[mcu] serial: /dev/btt-skr-14-turbo
What happened
I have a Prusa Mk3s with a SKR 1.4 turbo.
I'm trying to complete the initial setup but always get the same error, when I reach the "T0 TOOLBOARD PREPARATION" step:
Error Toolhead configuration cannot be deserialized, please check the configuration. hotendFan: Required partFan: Required
I've tried with another boards and the failure does not occur
What did you expect to happen
Continue the setup and generate config files.
How to reproduce
Get a SKR 1.4 turbo, flash it with Klipper and try to install Rat-Os 2.1.
Additional information
I'm using a Raspberry Pi 3b