Switch warning does not turn off in JETI/FRSKY versions.

Reini60 / er9x

Automatically exported from code.google.com/p/er9x

0 stars 0 forks source link

Switch warning does not turn off in JETI/FRSKY versions. #166

Closed GoogleCodeExporter closed 9 years ago

GoogleCodeExporter commented 9 years ago

What steps will reproduce the problem?
1. Load JETI/FRSKY FW.
2. Turn on.
3. Sw warning does not reset.

What is the expected output? What do you see instead?
Sw warning reset when all switches are in proper place.

Please use labels and text to provide additional information.

Original issue reported on code.google.com by erezra...@gmail.com on 11 Nov 2010 at 8:41

GoogleCodeExporter commented 9 years ago

Im glad that my first bugs that i noticed are here! You are faast Erezra! :)

rcgroups nick: ganapati08

Original comment by happygan...@gmail.com on 11 Nov 2010 at 9:40

GoogleCodeExporter commented 9 years ago

Now have the option to skip test.

Original comment by erezra...@gmail.com on 12 Nov 2010 at 7:45

GoogleCodeExporter commented 9 years ago

Issue 175 has been merged into this issue.

Original comment by erezra...@gmail.com on 17 Nov 2010 at 3:10

GoogleCodeExporter commented 9 years ago

Original comment by erezra...@gmail.com on 28 Nov 2010 at 10:23

Changed state: Fixed

GoogleCodeExporter commented 9 years ago

I just flashed the new firmware with the "fixed switch error" with the FrSky 
transmitter.

But the switch error still exists. Thou now I can go on by pressing a key.

So still not fixed

Original comment by medifra...@gmail.com on 28 Nov 2010 at 11:30

GoogleCodeExporter commented 9 years ago

Original comment by erezra...@gmail.com on 29 Nov 2010 at 5:24

Changed state: Accepted

GoogleCodeExporter commented 9 years ago

Got it now.

Original comment by erezra...@gmail.com on 2 Dec 2010 at 8:00

Changed state: Fixed

GoogleCodeExporter commented 9 years ago

Hi !!!

First, congratulation for your work... i'm appreciative...

I'm novice in this project...
So my question maybe has been already posed...
But I try at least !!! ;)

My config is : Turnigy 9x, BackLight, FrSky module, LiPo Batt...
And I flash my Tx with eePe and an AVR Card from SparkFun Electronics...

I use the Flash FrSky (but I've tried other version)... and it has appeared the 
mentions "AIL" and "THR" on level 1
I've tested with a Voltmeter the levels on the TX mainboard... 
I've noted that the pins "SCK" and "RST" remained at 5V !!!
So it's normal that AIL and THR are ON...

Could you do something ? 
Do you know the reason why SCK and RST remain at 5V ?
Have you a solution ?

Thanks for your answers
Thanks for all

Original comment by guillaum...@gmail.com on 27 Aug 2011 at 6:46

GoogleCodeExporter commented 9 years ago

If you flashed the Frsky version of the er9x firmware without making the 
hardware modification on your tx, then you will get that switch error... In 
that case try to flash the normal er9x version. I think that is your problem..

Original comment by joaoalve...@googlemail.com on 28 Aug 2011 at 12:40

GoogleCodeExporter commented 9 years ago

Hi!

Thanks for this answer...

I 've tryed to flash with the latest er9x...
And ... It 's OK !!! All is good !!!

But I must test the tx/rx connexion...

Original comment by guillaum...@gmail.com on 31 Aug 2011 at 3:38