beaglebone black installer no longer works

[jolan]

I ran:

sudo ./mk_mmc.sh --mmc /dev/sdb --dtb am335x-boneblack --distro trusty-armhf --serial-mode

Output here:

http://sprunge.us/ebSR

After placing the uSD card into bbb and booting:

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0 
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
** Unable to read file uEnv.txt **
gpio: pin 55 (gpio 55) value is 1
** Invalid partition 2 **
U-Boot#

Removed uSD and ran fdisk, there is not partition 2:

$ sudo fdisk /dev/sdb

Command (m for help): p

Disk /dev/sdb: 31.7 GB, 31657558016 bytes
64 heads, 32 sectors/track, 30191 cylinders, total 61831168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *        2048      100351       49152    e  W95 FAT16 (LBA)

Command (m for help): q

In #31, you said to remove the old eMMC bootloader first. I can't find instructions to do so.

Only how to "deal with it" from https://eewiki.net/display/linuxonarm/BeagleBone+Black#BeagleBoneBlack-DealingwitholdBootloaderineMMC

I followed those directions and got the same result:

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0 
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
** Unable to read file uEnv.txt **
gpio: pin 55 (gpio 55) value is 1
** Invalid partition 2 **

Verification:

jolan@mbp:~$ cat /mnt/boot/uEnv.txt 
##uname_r=current
##message=echo; echo Installer for [trusty-armhf] is using the Serial Interface; echo;
##mmcargs=run message; setenv bootargs console=ttyO0,115200n8 root=/dev/ram0 rw capemgr.disable_partno=BB-BONE-EMMC-2G

##This will work with: Angstrom's 2013.06.20 u-boot.

loadaddr=0x82000000
fdtaddr=0x88000000
rdaddr=0x88080000

initrd_high=0xffffffff
fdt_high=0xffffffff

loadximage=load mmc 0:2 ${loadaddr} /boot/vmlinuz-${uname_r}
loadxfdt=load mmc 0:2 ${fdtaddr} /boot/dtbs/${uname_r}/${fdtfile}
loadxrd=load mmc 0:2 ${rdaddr} /boot/initrd.img-${uname_r}; setenv rdsize ${filesize}
loaduEnvtxt=load mmc 0:2 ${loadaddr} /boot/uEnv.txt ; env import -t ${loadaddr} ${filesize};
loadall=run loaduEnvtxt; run loadximage; run loadxfdt;

mmcargs=setenv bootargs console=tty0 console=${console} ${optargs} ${cape_disable} ${cape_enable} root=${mmcroot} rootfstype=${mmcrootfstype} ${cmdline}

uenvcmd=run loadall; run mmcargs; bootz ${loadaddr} - ${fdtaddr};

[RobertCNelson]

Just boot up with: http://elinux.org/BeagleBoardUbuntu#BeagleBone.2FBeagleBone_Black

then

sudo dd if=/dev/zero of=/dev/mmcblk1

to wipe the old bootloader.. then the netinstall will work just fine...

[jolan]

Thanks, I didn't see anything about the bootloader changes before updating my image.