我想使用ESP32-S3-Korvo-2来运行fomo_detection_demo例程，需要修改什么地方

[monskate]

我修改了摄像头引脚配置但是运行程序无反应 ESP-ROM:esp32s3-20210327 Build:Mar 27 2021 rst:0x1 (POWERON),boot:0x28 (SPI_FAST_FLASH_BOOT) SPIWP:0xee mode:DIO, clock div:1 load:0x3fce3818,len:0x18dc load:0x403c9700,len:0x4 load:0x403c9704,len:0xd88 load:0x403cc700,len:0x2fa0 entry 0x403c9934 I (27) boot: ESP-IDF v5.1.4 2nd stage bootloader I (27) boot: compile time Oct 9 2024 14:28:08 I (27) boot: Multicore bootloader I (30) boot: chip revision: v0.2 I (34) qio_mode: Enabling default flash chip QIO I (39) boot.esp32s3: Boot SPI Speed : 80MHz I (44) boot.esp32s3: SPI Mode : QIO I (49) boot.esp32s3: SPI Flash Size : 8MB I (53) boot: Enabling RNG early entropy source... I (59) boot: Partition Table: I (62) boot: ## Label Usage Type ST Offset Length I (70) boot: 0 factory factory app 00 00 00010000 003bc000 I (77) boot: 1 nvs WiFi data 01 02 003cc000 00004000 I (84) boot: 2 fr Unknown data 01 06 003d0000 00020000 I (92) boot: 3 db Unknown data 01 06 003f0000 00010000 I (99) boot: 4 models Unknown data 01 06 00400000 00400000 I (107) boot: End of partition table I (111) esp_image: segment 0: paddr=00010020 vaddr=3c0e0020 size=778dch (489692) map I (194) esp_image: segment 1: paddr=00087904 vaddr=3fc9c200 size=05b98h ( 23448) load I (198) esp_image: segment 2: paddr=0008d4a4 vaddr=40374000 size=02b74h ( 11124) load I (202) esp_image: segment 3: paddr=00090020 vaddr=42000020 size=df3e0h (914400) map I (347) esp_image: segment 4: paddr=0016f408 vaddr=40376b74 size=15604h ( 87556) load I (374) boot: Loaded app from partition at offset 0x10000 I (374) boot: Disabling RNG early entropy source... I (375) cpu_start: Multicore app I (379) octal_psram: vendor id : 0x0d (AP) I (383) octal_psram: dev id : 0x02 (generation 3) I (389) octal_psram: density : 0x03 (64 Mbit) I (395) octal_psram: good-die : 0x01 (Pass) I (400) octal_psram: Latency : 0x01 (Fixed) I (405) octal_psram: VCC : 0x01 (3V) I (410) octal_psram: SRF : 0x01 (Fast Refresh) I (416) octal_psram: BurstType : 0x01 (Hybrid Wrap) I (422) octal_psram: BurstLen : 0x01 (32 Byte) I (427) octal_psram: Readlatency : 0x02 (10 cycles@Fixed) I (434) octal_psram: DriveStrength: 0x00 (1/1) I (439) MSPI Timing: PSRAM timing tuning index: 5 I (444) esp_psram: Found 8MB PSRAM device I (449) esp_psram: Speed: 80MHz I (453) cpu_start: Pro cpu up. I (456) cpu_start: Starting app cpu, entry point is 0x403757d4

[iChizer0]

您好,很抱歉我们无法从您提供的日志中定位问题,如果方便的话,请告知我们您使用的摄像头型号和您调整后的引脚配置.

此外,我们建议你修改 examples/fomo_detection_demo/main/app_main.cpp 中关于 Display 的代码,将和 display 相关的代码注释即可.

[monskate]

您好,很抱歉我们无法从您提供的日志中定位问题,如果方便的话,请告知我们您使用的摄像头型号和您调整后的引脚配置.

此外,我们建议你修改 examples/fomo_detection_demo/main/app_main.cpp 中关于 Display 的代码,将和 display 相关的代码注释即可.

您好，我使用的是ov2640,引脚为：

define CAMERA_PIN_PWDN -1

define CAMERA_PIN_RESET -1

define CAMERA_PIN_VSYNC 21

define CAMERA_PIN_HREF 38

define CAMERA_PIN_PCLK 11

define CAMERA_PIN_XCLK 40

define CAMERA_PIN_SIOD 17

define CAMERA_PIN_SIOC 18

define CAMERA_PIN_D0 13

define CAMERA_PIN_D1 47

define CAMERA_PIN_D2 14

define CAMERA_PIN_D3 3

define CAMERA_PIN_D4 12

define CAMERA_PIN_D5 42

define CAMERA_PIN_D6 41

define CAMERA_PIN_D7 39

我在尝试注释display