Issues booting into Ventura

[BugByte14]

Hello! I have an Asus B550-f (AMD) motherboard which has an i225-v ethernet controller. However, when I enable the kext I can't boot into the os.

I get the following message that hangs for a couple seconds and then repeats:

ALUC:clientDied(PID: ###), lifsd_entitled 1 koio_entitled 0
ALUC:init(PID: ###), lifsd_entitlement 1 koio_entitlement 0
methodSetClientDomain entered
registerNotificationPort entered

My Kexts:

• AppleALC
• AppleIGC (The one that causes the os not to boot)
• AppleMCEReporterDisabler
• Lilu
• NVMEFix
• VirtualSMC
• WhateverGreen

Additionally, I've verified that DisableIOMapper is enabled, but it didn't make a difference. Any advice?

[rx-837]

Hello! I have an Asus B550-f (AMD) motherboard which has an i225-v ethernet controller. However, when I enable the kext I can't boot into the os.

I get the following message that hangs for a couple seconds and then repeats:

ALUC:clientDied(PID: ###), lifsd_entitled 1 koio_entitled 0
ALUC:init(PID: ###), lifsd_entitlement 1 koio_entitlement 0
methodSetClientDomain entered
registerNotificationPort entered

My Kexts:

• AppleALC
• AppleIGC (The one that causes the os not to boot)
• AppleMCEReporterDisabler
• Lilu
• NVMEFix
• VirtualSMC
• WhateverGreen

Additionally, I've verified that DisableIOMapper is enabled, but it didn't make a difference. Any advice?

i have similar issue on Gigabyte Z490 AORUS PRO AX. Startup, shutdown and restart takes a long time with subject kext.

On tomato forum writes that i225-v controller have native support in Ventura by com.apple.DriverKit-AppleEthernetE1000(https://www.tonymacx86.com/threads/help-ventura-freezing-at-login.322811/page-4#post-2345073)

[5T33Z0]

@rx-837: Have a look at this: https://github.com/5T33Z0/OC-Little-Translated/blob/main/01_Adding_missing_Devices_and_enabling_Features/Intel_I225-V_Fix_(SSDT-I225V)/README.md#method-1-add-appleigckext

[rx-837]

@rx-837: Have a look at this: https://github.com/5T33Z0/OC-Little-Translated/blob/main/01_Adding_missing_Devices_and_enabling_Features/Intel_I225-V_Fix_(SSDT-I225V)/README.md#method-1-add-appleigckext

I have seen it.

For my board with latest biosVendor ID, Subsystem Vendor ID and SubSystem ID is correct. My OC version is 0.8.3, i see no reason to update it. VT-d is enabled, DisableIoMapper enabled(https://dortania.github.io/OpenCore-Install-Guide/config.plist/comet-lake.html#quirks-3).

I have revert the actions from Dortanya's documentation with network controller and Mac OS identified it as Intel(R) I225 V with com.apple.DriverKit-AppleEthernetE1000 driver.

Why I should use AppleIGC kext when device is defined correctly?

[5T33Z0]

My OC version is 0.8.3, i see no reason to update it.

There were some significant updates to OpenCore since 0.8.3 in regards to Ventura. So you are using a version of OpenCore which is more than a year old with a kext which is couple of months old.