Does anyone know why the driver would fail for no reason? The controller is about 1.5 years old with a maximum of 20 jobs done.
I sent an email to support but soon as he found out that I didn't purchase it directly from him, (purchased from local shop) he just ignored my emails. Shit house customer support if you ask me.
Just started grinding mid job. Swapped the motors around and the issue remains on the Y2. Did a FW update and its still the same.
CNCjs 1.9.26 [Grbl]
Connected to COM3 with a baud rate of 115200
ets Jun 8 2016 00:22:57
rst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:9720
ho 0 tail 12 room 4
load:0x40080400,len:6352
entry 0x400806b8
[MSG:Grbl_ESP32 Ver 1.3a Date 20220621]
[MSG:Compiled with ESP32 SDK:v3.2.3]
[MSG:Using machine:CNC_xPRO_V5_XYYZ_NC]
[MSG:Axis count 3]
[MSG:RMT Steps]
[MSG:Door switch on pin GPIO(16)]
[MSG:Macro Pin 1 GPIO(13)]
[MSG:Macro Pin 2 GPIO(0)]
[MSG:Init Motors]
[MSG:TMCStepper Library Ver. 0x000701]
[MSG:X Axis Trinamic TMC5160 Step:GPIO(12) Dir:GPIO(14) CS:GPIO(17) Disable:None Index:1 R:0.050 Limits(0.000,300.000)]
[MSG:X Axis Trinamic driver test passed]
[MSG:Y Axis Trinamic TMC5160 Step:GPIO(27) Dir:GPIO(26) CS:GPIO(17) Disable:None Index:2 R:0.050 Limits(0.000,300.000)]
[MSG:Y Axis Trinamic driver test passed]
[MSG:Y2 Axis Trinamic TMC5160 Step:GPIO(33) Dir:GPIO(32) CS:GPIO(17) Disable:None Index:3 R:0.050 Limits(0.000,300.000)]
[MSG:Y2 Axis Trinamic driver test passed]
[MSG:Z Axis Trinamic TMC5160 Step:GPIO(15) Dir:GPIO(2) CS:GPIO(17) Disable:None Index:4 R:0.050 Limits(-300.000,0.000)]
[MSG:Z Axis Trinamic driver test passed]
[MSG:No spindle]
[MSG:Local access point CNC_xPRO_V5 started, 192.168.0.1]
[MSG:Captive Portal Started]
[MSG:HTTP Started]
[MSG:TELNET Started 23]
[MSG:Mist coolant on pin GPIO(21)]
[MSG:X Axis limit switch on pin GPIO(35)]
[MSG:Y Axis limit switch on pin GPIO(34)]
[MSG:Z Axis limit switch on pin GPIO(39)]
[MSG:Probe on pin GPIO(22)]
Grbl 1.3a ['$' for help]
client> $$
Hi All,
Does anyone know why the driver would fail for no reason? The controller is about 1.5 years old with a maximum of 20 jobs done. I sent an email to support but soon as he found out that I didn't purchase it directly from him, (purchased from local shop) he just ignored my emails. Shit house customer support if you ask me.
Just started grinding mid job. Swapped the motors around and the issue remains on the Y2. Did a FW update and its still the same.
CNCjs 1.9.26 [Grbl] Connected to COM3 with a baud rate of 115200 ets Jun 8 2016 00:22:57 rst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1216 ho 0 tail 12 room 4 load:0x40078000,len:9720 ho 0 tail 12 room 4 load:0x40080400,len:6352 entry 0x400806b8 [MSG:Grbl_ESP32 Ver 1.3a Date 20220621] [MSG:Compiled with ESP32 SDK:v3.2.3] [MSG:Using machine:CNC_xPRO_V5_XYYZ_NC] [MSG:Axis count 3] [MSG:RMT Steps] [MSG:Door switch on pin GPIO(16)] [MSG:Macro Pin 1 GPIO(13)] [MSG:Macro Pin 2 GPIO(0)] [MSG:Init Motors] [MSG:TMCStepper Library Ver. 0x000701] [MSG:X Axis Trinamic TMC5160 Step:GPIO(12) Dir:GPIO(14) CS:GPIO(17) Disable:None Index:1 R:0.050 Limits(0.000,300.000)] [MSG:X Axis Trinamic driver test passed] [MSG:Y Axis Trinamic TMC5160 Step:GPIO(27) Dir:GPIO(26) CS:GPIO(17) Disable:None Index:2 R:0.050 Limits(0.000,300.000)] [MSG:Y Axis Trinamic driver test passed] [MSG:Y2 Axis Trinamic TMC5160 Step:GPIO(33) Dir:GPIO(32) CS:GPIO(17) Disable:None Index:3 R:0.050 Limits(0.000,300.000)] [MSG:Y2 Axis Trinamic driver test passed] [MSG:Z Axis Trinamic TMC5160 Step:GPIO(15) Dir:GPIO(2) CS:GPIO(17) Disable:None Index:4 R:0.050 Limits(-300.000,0.000)] [MSG:Z Axis Trinamic driver test passed] [MSG:No spindle] [MSG:Local access point CNC_xPRO_V5 started, 192.168.0.1] [MSG:Captive Portal Started] [MSG:HTTP Started] [MSG:TELNET Started 23] [MSG:Mist coolant on pin GPIO(21)] [MSG:X Axis limit switch on pin GPIO(35)] [MSG:Y Axis limit switch on pin GPIO(34)] [MSG:Z Axis limit switch on pin GPIO(39)] [MSG:Probe on pin GPIO(22)] Grbl 1.3a ['$' for help] client> $$