FBester1976
commented
8 months ago Good morning,
Some questions…
What does the serial monitor say? Keep your ESP32 plugged into the PC when you start it…serial monitor will state errors. @. What version of software are you using? Do you have the battery protection activated (3_ESC tab)? @.
I can see from your video that your ESC is plugged into the wrong position (not Ch1, needs to go to ESC.) @. @.
Also plug in a speaker when you make the next video please.
Regards,
Frikkie
INTERNAL
From: RS33D @.> Sent: Friday, March 15, 2024 8:33 AM To: TheDIYGuy999/Rc_Engine_Sound_ESP32 @.> Cc: Subscribed @.***> Subject: [TheDIYGuy999/Rc_Engine_Sound_ESP32] ESP32 Blue Light Blinking !!Help Please!! (Issue #69)
Hello
Your ESP32 engine sound project is very nice, currently trying to put it into my 3d printed 1/14 scale kenworth
But i have an issue with the circuit board not working, please see the below google drive video
https://drive.google.com/file/d/1ZZUraMMt_CvwXIOm6ZMI8HmvmG5yAJjD/view?usp=sharing
I have not adjusted the code as i want to use Sbus so just loaded the code up, but as per the video you can see that when turned on the blue light just flashes
i have adjusted the settings on the remote i am using which is a Flysky FS i6x and has its serial output set on S Bus, the receiver is also s bus compatible, i am using a flysky ia10b s receiver
i have also tried ibus, PWM and PPM and all result in the same issue
What have i done wrong??
your help would be much appreciated
many thanks
Lawson
— Reply to this email directly, view it on GitHubhttps://github.com/TheDIYGuy999/Rc_Engine_Sound_ESP32/issues/69, or unsubscribehttps://github.com/notifications/unsubscribe-auth/ASXSVQZMZYVPOENBQI6HQE3YYKI2RAVCNFSM6AAAAABEXN25E6VHI2DSMVQWIX3LMV43ASLTON2WKOZSGE4DOOBSGA4DCOA. You are receiving this because you are subscribed to this thread.Message ID: @.**@.>> Volkswagen Group Africa Chairperson & Managing Director:
M Biene*
Directors: R Coleman (Human Resources) N Maliza (Corporate & Government Affairs) T Milz* (Sales and Marketing) F Ribeiro* (Finance) U Schwabe (Production)
M Raphulu (Non-Executive)
German* Brazilian**
Volkswagen of South Africa (Pty) Ltd is proudly Level 3 B-BBEE compliant
DISCLAIMER : Registered Name: Volkswagen of South Africa (Pty) Ltd (Reg No. 1946/023458/07), trading as Volkswagen Group Africa
Any views expressed in this message are those of the individual sender. No liability shall attach whatsoever to Volkswagen of South Africa from this communication except where the sender is acting on specific authority of Volkswagen of South Africa, such authority being public record and acknowledged by Volkswagen of South Africa by nature of the employee's functions. This document may in no way be photocopied, printed, scanned or electronically duplicated for any purposes other than that for which it was originally intended. If you are not the intended recipient of this communication, please discard this message and notify Volkswagen of South Africa immediately at @.*** Volkswagen of South Africa's anonymous toll free ethics number is: 080 111 3949
RS33D
Hello
Your ESP32 engine sound project is very nice, currently trying to put it into my 3d printed 1/14 scale kenworth
But i have an issue with the circuit board not working, please see the below google drive video
https://drive.google.com/file/d/1ZZUraMMt_CvwXIOm6ZMI8HmvmG5yAJjD/view?usp=sharing
I have not adjusted the code as i want to use Sbus so just loaded the code up, but as per the video you can see that when turned on the blue light just flashes
i have adjusted the settings on the remote i am using which is a Flysky FS i6x and has its serial output set on S Bus, the receiver is also s bus compatible, i am using a flysky ia10b s receiver
i have also tried ibus, PWM and PPM and all result in the same issue
What have i done wrong??
your help would be much appreciated
many thanks
Lawson