Support for Ender 3 S1 ProX

[Waldehyd]

I got a new 2024 Version of the Ender 3 S1 Pro called ProX. It supposedly prints faster, but only due to Firmware changes. Do you have any information on whether it's a good idea to flash it with a new Firmware?

[ThomasToka]

Any links to the machine or its used firmware.

Can you connect with a terminal and show me the output of:

M503 M115

[ThomasToka]

It seems its only a marketing thing to call it ProX with the F28 firmware.

https://forum.creality.com/t/difference-between-ender-3-s1-pro-and-ender-3-s1-prox/8957/9

So its supported out of the box with my firmware.

If you can provide the M503 and M115 for inspection.

For now i will close this here. You can still answer here.

[Waldehyd]

I see, thanks, for completeness:

Send: M503 Recv: echo: G21 ; Units in mm (mm) Recv: Recv: echo:; Filament settings: Disabled Recv: echo: M200 S0 D1.75 Recv: echo:; Steps per unit: Recv: echo: M92 X80.00 Y80.00 Z400.00 E424.90 Recv: echo:; Maximum feedrates (units/s): Recv: echo: M203 X500.00 Y500.00 Z10.00 E25.00 Recv: echo:; Maximum Acceleration (units/s2): Recv: echo: M201 X5000.00 Y5000.00 Z100.00 E5000.00 Recv: echo:; Acceleration (units/s2): P R T Recv: echo: M204 P500.00 R1500.00 T500.00 Recv: echo:; Advanced: B S T X Y Z E Recv: echo: M205 B20000.00 S0.00 T0.00 X15.00 Y15.00 Z0.40 E5.00 Recv: echo:; Home offset: Recv: echo: M206 X0.00 Y0.00 Z0.00 Recv: echo:; Auto Bed Leveling: Recv: echo: M420 S1 Z10.00 Recv: echo: G29 W I0 J0 Z0.18500 Recv: echo: G29 W I1 J0 Z0.25650 Recv: echo: G29 W I2 J0 Z0.17400 Recv: echo: G29 W I3 J0 Z-0.09950 Recv: echo: G29 W I0 J1 Z0.15400 Recv: echo: G29 W I1 J1 Z0.12700 Recv: echo: G29 W I2 J1 Z0.04500 Recv: echo: G29 W I3 J1 Z-0.14200 Recv: echo: G29 W I0 J2 Z0.09400 Recv: echo: G29 W I1 J2 Z0.06150 Recv: echo: G29 W I2 J2 Z-0.01400 Recv: echo: G29 W I3 J2 Z-0.19600 Recv: echo: G29 W I0 J3 Z0.06600 Recv: echo: G29 W I1 J3 Z0.13600 Recv: echo: G29 W I2 J3 Z0.06900 Recv: echo: G29 W I3 J3 Z-0.14900 Recv: echo:; Material heatup parameters: Recv: echo: M145 S0 H200.00 B60.00 F255 Recv: echo: M145 S1 H240.00 B110.00 F255 Recv: echo:; PID settings: Recv: echo: M301 P30.82 I4.19 D56.70 Recv: echo: M304 P174.91 I34.70 D587.69 Recv: echo:; Power-Loss Recovery: Recv: echo: M413 S1 Recv: echo:; Z-Probe Offset (mm): Recv: echo: M851 X-31.80 Y-40.50 Z-2.75 Recv: Input Shaping: Recv: M593 X F50.00 D0.15 Recv: M593 Y F35.00 D0.15 Recv: echo:; Filament load/unload lengths: Recv: echo: M603 L0.00 U100.00 Recv: echo:; Filament runout sensor: Recv: echo: M412 S1 Recv: echo:; UI Language: Recv: echo: M414 S0

---

Recv: FIRMWARE_NAME:Marlin 2.0.8.28F4 (Jun 19 2023 18:06:53) SOURCE_CODE_URL:github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:Ender-3 S1 Pro EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff Recv: Cap:SERIAL_XON_XOFF:0 Recv: Cap:BINARY_FILE_TRANSFER:0 Recv: Cap:IS_PLR:0 Recv: Cap:EEPROM:1 Recv: Cap:VOLUMETRIC:1 Recv: Cap:AUTOREPORT_POS:0 Recv: Cap:AUTOREPORT_TEMP:1 Recv: Cap:PROGRESS:0 Recv: Cap:PRINT_JOB:1 Recv: Cap:AUTOLEVEL:1 Recv: Cap:RUNOUT:1 Recv: Cap:Z_PROBE:1 Recv: Cap:LEVELING_DATA:1 Recv: Cap:BUILD_PERCENT:0 Recv: Cap:SOFTWARE_POWER:0 Recv: Cap:TOGGLE_LIGHTS:0 Recv: Cap:CASE_LIGHT_BRIGHTNESS:0 Recv: Cap:EMERGENCY_PARSER:0 Recv: Cap:HOST_ACTION_COMMANDS:0 Recv: Cap:PROMPT_SUPPORT:0 Recv: Cap:SDCARD:1 Recv: Cap:REPEAT:0 Recv: Cap:SD_WRITE:1 Recv: Cap:AUTOREPORT_SD_STATUS:0 Recv: Cap:LONG_FILENAME:1 Recv: Cap:THERMAL_PROTECTION:1 Recv: Cap:MOTION_MODES:0 Recv: Cap:ARCS:1 Recv: Cap:BABYSTEPPING:1 Recv: Cap:CHAMBER_TEMPERATURE:0 Recv: Cap:COOLER_TEMPERATURE:0 Recv: Cap:MEATPACK:0 Recv: ok

[ThomasToka]

As expected. Same firmware as on all other pros.

Thanks for the outputs.