Firmware update fails to flash, will not "fit"

[kingozone]

Currently running Klipper on Ender 3 V3 SE. Recently updated, and needed to update the Exapnder board. When I try to update it, I get the following error:

biqu@BTT-CB1:~/klipper$ make clean biqu@BTT-CB1:~/klipper$ make flash FLASH_DEVICE=0483:df11 Creating symbolic link out/board Building out/autoconf.h Compiling out/src/sched.o Compiling out/src/command.o Compiling out/src/basecmd.o Compiling out/src/debugcmds.o Compiling out/src/initial_pins.o Compiling out/src/gpiocmds.o Compiling out/src/stepper.o Compiling out/src/endstop.o Compiling out/src/trsync.o Compiling out/src/dirzctl.o Compiling out/src/hx711s.o Compiling out/src/adccmds.o Compiling out/src/spicmds.o Compiling out/src/i2ccmds.o Compiling out/src/buttons.o Compiling out/src/tmcuart.o Compiling out/src/neopixel.o Compiling out/src/pulse_counter.o Compiling out/src/lcd_st7920.o Compiling out/src/lcd_hd44780.o Compiling out/src/spi_software.o Compiling out/src/thermocouple.o Compiling out/src/sensor_adxl345.o Compiling out/src/sensor_angle.o Compiling out/src/sensor_mpu9250.o Compiling out/src/sensor_bulk.o Compiling out/src/stm32/watchdog.o Compiling out/src/stm32/gpio.o Compiling out/src/stm32/clockline.o Compiling out/src/stm32/dfu_reboot.o Compiling out/src/generic/crc16_ccitt.o Compiling out/src/generic/armcm_boot.o Compiling out/src/generic/armcm_irq.o Compiling out/src/generic/armcm_reset.o Compiling out/src/../lib/stm32f0/system_stm32f0xx.o Compiling out/src/generic/timer_irq.o Compiling out/src/stm32/stm32f0_timer.o Compiling out/src/stm32/stm32f0.o Compiling out/src/stm32/gpioperiph.o Compiling out/src/stm32/stm32f0_adc.o Compiling out/src/stm32/stm32f0_i2c.o Compiling out/src/stm32/spi.o Compiling out/src/stm32/usbfs.o Compiling out/src/stm32/chipid.o Compiling out/src/generic/usb_cdc.o Building out/compile_time_request.o Version: 25778772 Preprocessing out/src/generic/armcm_link.ld Linking out/klipper.elf /usr/lib/gcc/arm-none-eabi/8.3.1/../../../arm-none-eabi/bin/ld: out/klipper.elf section .text' will not fit in regionrom' /usr/lib/gcc/arm-none-eabi/8.3.1/../../../arm-none-eabi/bin/ld: region `rom' overflowed by 10512 bytes collect2: error: ld returned 1 exit status make: *** [Makefile:72: out/klipper.elf] Error 1

How can I fix this? I have followed the manual and everytime, I get this error.

[timmit99]

Can you share screenshots of your menuconfig and advanced options please?

[kingozone]

[kingozone]

After buying a second one, I'm getting the same results. Was curious if something was stuck, so I tried a reflash of an ADXL, no problem. Run a make clean, try again for the board, same issue.

[kingozone]

Any ideas?