I have 2 routers, One from the ISP (Bridgemode cannot be enabled) So I turn off DHCP on that and set a static route to my ER-X then apply DMZ from ISP to ER-X.
This is my config file.
firewall {
all-ping enable
broadcast-ping disable
ipv6-name WANv6_IN {
default-action drop
description "WAN inbound traffic forwarded to LAN"
enable-default-log
rule 10 {
action accept
description "Allow established/related sessions"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
ipv6-name WANv6_LOCAL {
default-action drop
description "WAN inbound traffic to the router"
enable-default-log
rule 10 {
action accept
description "Allow established/related sessions"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
rule 30 {
action accept
description "Allow IPv6 icmp"
protocol ipv6-icmp
}
rule 40 {
action accept
description "allow dhcpv6"
destination {
port 546
}
protocol udp
source {
port 547
}
}
}
ipv6-receive-redirects disable
ipv6-src-route disable
ip-src-route disable
log-martians enable
modify mullvad_route {
rule 10 {
action modify
description mullvad-vpn
modify {
table 1
}
source {
address 192.168.101.0/24
}
}
}
name WAN_IN {
default-action drop
description "WAN to internal"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
name WAN_LOCAL {
default-action drop
description "WAN to router"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
rule 30 {
action accept
description wireguard
destination {
port 51820
}
log disable
protocol udp
}
}
receive-redirects disable
send-redirects enable
source-validation disable
syn-cookies enable
}
interfaces {
ethernet eth0 {
address 192.168.70.4/24
description Internet
duplex auto
firewall {
in {
ipv6-name WANv6_IN
name WAN_IN
}
local {
ipv6-name WANv6_LOCAL
name WAN_LOCAL
}
}
speed auto
}
ethernet eth1 {
description Local
duplex auto
speed auto
}
ethernet eth2 {
description Local
duplex auto
speed auto
}
ethernet eth3 {
description Local
duplex auto
speed auto
}
ethernet eth4 {
description Local
duplex auto
poe {
output off
}
speed auto
}
loopback lo {
}
switch switch0 {
address 192.168.101.1/24
description Local
firewall {
in {
modify mullvad_route
}
}
mtu 1500
switch-port {
interface eth1 {
}
interface eth2 {
}
interface eth3 {
}
interface eth4 {
}
vlan-aware disable
}
}
wireguard wg0 {
address 10.xx.xx.xx/32
listen-port 51820
mtu 1300
peer vtqDtifokiHna0eBshGdJLedj/lzGW+iDvWKx+YjDFs= {
allowed-ips 0.0.0.0/0
endpoint 193.xxx.xxx.xx:51820
}
private-key /config/auth/wg.key
route-allowed-ips false
}
}
protocols {
static {
table 1 {
description "table to force wg0:mullvad"
interface-route 0.0.0.0/0 {
next-hop-interface wg0 {
}
}
route 0.0.0.0/0 {
blackhole {
distance 255
}
}
}
}
}
service {
dhcp-server {
disabled false
hostfile-update disable
shared-network-name LAN {
authoritative enable
subnet 192.168.101.0/24 {
default-router 192.168.101.1
dns-server 192.168.101.1
lease 86400
start 192.168.101.38 {
stop 192.168.101.243
}
}
}
static-arp disable
use-dnsmasq disable
}
dns {
forwarding {
cache-size 150
listen-on switch0
}
}
gui {
http-port 80
https-port 443
older-ciphers enable
}
nat {
rule 5000 {
description mullvad-nat
outbound-interface wg0
source {
address 192.168.101.0/24
}
type masquerade
}
rule 5010 {
description "masquerade for WAN"
outbound-interface eth0
type masquerade
}
}
ssh {
port 22
protocol-version v2
}
unms {
disable
}
}
system {
analytics-handler {
send-analytics-report false
}
crash-handler {
send-crash-report false
}
gateway-address 192.168.70.1
host-name xxxxxxxxx
login {
user admin {
authentication {
encrypted-password $5$AuS/1U4/GFtBa.ny$RbDAbH.bVCo5eKPwYG6mhZHbWWitalnUAbl0eZrNN05
}
level admin
}
}
name-server 192.168.70.1
ntp {
server 0.ubnt.pool.ntp.org {
}
server 1.ubnt.pool.ntp.org {
}
server 2.ubnt.pool.ntp.org {
}
server 3.ubnt.pool.ntp.org {
}
}
syslog {
global {
facility all {
level notice
}
facility protocols {
level debug
}
}
}
time-zone UTC
}
/* Warning: Do not remove the following line. */
/* === vyatta-config-version: "config-management@1:conntrack@1:cron@1:dhcp-relay@1:dhcp-server@4:firewall@5:ipsec@5:nat@3:qos@1:quagga@2:suspend@1:system@5:ubnt-l2tp@1:ubnt-pptp@1:ubnt-udapi-server@1:ubnt-unms@2:ubnt-util@1:vrrp@1:vyatta-netflow@1:webgui@1:webproxy@1:zone-policy@1" === */
/* Release version: v2.0.9.5346345.201028.1647 */
Hi there.
I have setup wireguard however I don't have internet when I enable or setup wireguard.https://www.reddit.com/r/Ubiquiti/comments/9l5io9/review_my_simple_wireguard_vpn_setup_for_erx/
I have 2 routers, One from the ISP (Bridgemode cannot be enabled) So I turn off DHCP on that and set a static route to my ER-X then apply DMZ from ISP to ER-X.
This is my config file.