search

Xilinx / PYNQ

Python Productivity for ZYNQ
http://www.pynq.io/
BSD 3-Clause "New" or "Revised" License
1.99k stars 817 forks source link

fpga_manager fpga0: Error while writing image data to FPGA with ZCU 102 #767

Closed hisrg closed 5 years ago

hisrg commented 5 years ago

image

There are some error message as above picture，the console has print the message as left window, and display source in jupyter notebook. the board is ZCU102 ZU+ MPSoc produced in 03,NOV,2018. I build this uboot file and pynq image according to some guide, there are more detail as below.

  1. I download this board image from here

image

http://www.pynq.io/board.html and use uboot image tools write it to my SD card.

  1. I create a ZCU102 project in petalinux 2018.2 and use vivado 2018.2.2 to generate hdf file, the ZCU102 BSP file comes from here:

image

https://www.xilinx.com/support/download/index.html/content/xilinx/en/downloadNav/embedded-design-tools.html

  1. I built this project in petalinux 2018.2 according Ug1144 guide, and the I copy some files as below to boot pairttion of SD Card. image

1) Enable FPGA firmware Manger 2) Enable PMU https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842462/Build+PMU+Firmware

3) Enable DTG tree https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841847/Solution+ZynqMP+PL+Programming

  1. I turn on the ZCU 102 board, the boot log has printed as follow, Xilinx Zynq MP First Stage Boot Loader Release 2018.2 Dec 2 2018 - 01:20:45 NOTICE: ATF running on XCZU9EG/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: Secure code at 0x0 NOTICE: BL31: Non secure code at 0x8000000 NOTICE: BL31: v1.4(release):xilinx-v2018.1-4-g93a69a5a NOTICE: BL31: Built : 13:00:31, Dec 4 2018 PMUFW: v1.0

U-Boot 2018.01 (Dec 04 2018 - 05:01:29 -0800) Xilinx ZynqMP ZCU102 rev1.0

I2C: ready DRAM: 4 GiB EL Level: EL2 Chip ID: zu9eg MMC: sdhci@ff170000: 0 (SD) SF: Detected n25q512a with page size 512 Bytes, erase size 128 KiB, total 128 MiB *** Warning - bad CRC, using default environment

In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Model: ZynqMP ZCU102 Rev1.0 Board: Xilinx ZynqMP Bootmode: LVL_SHFT_SD_MODE1 Net: ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id eth0: ethernet@ff0e0000 U-BOOT for zcu102n

ethernet@ff0e0000 Waiting for PHY auto negotiation to complete....... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 BOOTP broadcast 9 BOOTP broadcast 10 BOOTP broadcast 11 BOOTP broadcast 12 BOOTP broadcast 13 BOOTP broadcast 14 BOOTP broadcast 15 BOOTP broadcast 16 BOOTP broadcast 17

Retry time exceeded Hit any key to stop autoboot: 0 Device: sdhci@ff170000 Manufacturer ID: 3 OEM: 5344 Name: SL16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 14.8 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading image.ub 7057744 bytes read in 472 ms (14.3 MiB/s)

Loading kernel from FIT Image at 10000000 ...

Using 'conf@system-top.dtb' configuration Trying 'kernel@1' kernel subimage Description: Linux kernel Type: Kernel Image Compression: gzip compressed Data Start: 0x10000104 Data Size: 7014059 Bytes = 6.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x00080000 Entry Point: 0x00080000 Hash algo: sha1 Hash value: b0634fc0f85985a6616eeb070107371f47f15988 Verifying Hash Integrity ... sha1+ OK

Loading fdt from FIT Image at 10000000 ...

Using 'conf@system-top.dtb' configuration Trying 'fdt@system-top.dtb' fdt subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x106b08b4 Data Size: 41768 Bytes = 40.8 KiB Architecture: AArch64 Hash algo: sha1 Hash value: ab355306d3c7ca3c23ffd5950ff182e7b70167a4 Verifying Hash Integrity ... sha1+ OK Booting using the fdt blob at 0x106b08b4 Uncompressing Kernel Image ... OK Loading Device Tree to 0000000007ff2000, end 0000000007fff327 ... OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #1 SMP Tue Dec 4 05:05:42 PST 2018 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Machine model: ZynqMP ZCU102 Rev1.0 [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] bootconsole [cdns0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 256 MiB at 0x000000006fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff62000 s46488 r8192 d31336 u86016 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1033987 [ 0.000000] Kernel command line: earlycon clk_ignore_unused root=/dev/mmcblk0p2 rw rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff] [ 0.000000] Memory: 3784184K/4193280K available (10044K kernel code, 652K rwdata, 3168K rodata, 512K init, 2369K bss, 146952K reserved, 262144K cma-r [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008a50000 ( 10048 KB) [ 0.000000] .rodata : 0xffffff8008a50000 - 0xffffff8008d70000 ( 3200 KB) [ 0.000000] .init : 0xffffff8008d70000 - 0xffffff8008df0000 ( 512 KB) [ 0.000000] .data : 0xffffff8008df0000 - 0xffffff8008e93200 ( 653 KB) [ 0.000000] .bss : 0xffffff8008e93200 - 0xffffff80090e36b0 ( 2370 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf1dc00000 ( 476 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc880000000 ( 34816 MB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x170f8dc196, max_idle_ns: 440795203664 ns [ 0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511099ns [ 0.008303] Console: colour dummy device 80x25 [ 0.012560] console [tty0] enabled [ 0.015925] bootconsole [cdns0] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #1 SMP Tue Dec 4 05:05:42 PST 2018 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Machine model: ZynqMP ZCU102 Rev1.0 [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] bootconsole [cdns0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 256 MiB at 0x000000006fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff62000 s46488 r8192 d31336 u86016 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1033987 [ 0.000000] Kernel command line: earlycon clk_ignore_unused root=/dev/mmcblk0p2 rw rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff] [ 0.000000] Memory: 3784184K/4193280K available (10044K kernel code, 652K rwdata, 3168K rodata, 512K init, 2369K bss, 146952K reserved, 262144K cma-r [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008a50000 ( 10048 KB) [ 0.000000] .rodata : 0xffffff8008a50000 - 0xffffff8008d70000 ( 3200 KB) [ 0.000000] .init : 0xffffff8008d70000 - 0xffffff8008df0000 ( 512 KB) [ 0.000000] .data : 0xffffff8008df0000 - 0xffffff8008e93200 ( 653 KB) [ 0.000000] .bss : 0xffffff8008e93200 - 0xffffff80090e36b0 ( 2370 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf1dc00000 ( 476 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc880000000 ( 34816 MB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x170f8dc196, max_idle_ns: 440795203664 ns [ 0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511099ns [ 0.008303] Console: colour dummy device 80x25 [ 0.012560] console [tty0] enabled [ 0.015925] bootconsole [cdns0] disabled [ 0.019836] Calibrating delay loop (skipped), value calculated using timer frequency.. 199.98 BogoMIPS (lpj=399960) [ 0.019850] pid_max: default: 32768 minimum: 301 [ 0.019953] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.019971] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.020528] ASID allocator initialised with 65536 entries [ 0.020577] Hierarchical SRCU implementation. [ 0.020909] EFI services will not be available. [ 0.020934] zynqmp_plat_init Platform Management API v1.0 [ 0.020942] zynqmp_plat_init Trustzone version v1.0 [ 0.021036] smp: Bringing up secondary CPUs ... [ 0.021286] Detected VIPT I-cache on CPU1 [ 0.021313] CPU1: Booted secondary processor [410fd034] [ 0.021586] Detected VIPT I-cache on CPU2 [ 0.021604] CPU2: Booted secondary processor [410fd034] [ 0.021865] Detected VIPT I-cache on CPU3 [ 0.021883] CPU3: Booted secondary processor [410fd034] [ 0.021924] smp: Brought up 1 node, 4 CPUs [ 0.021956] SMP: Total of 4 processors activated. [ 0.021963] CPU features: detected feature: 32-bit EL0 Support [ 0.021974] CPU: All CPU(s) started at EL2 [ 0.021989] alternatives: patching kernel code [ 0.022709] devtmpfs: initialized [ 0.027218] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0 [ 0.027432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.027453] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.027587] random: fast init done [ 0.032859] xor: measuring software checksum speed [ 0.071907] 8regs : 2302.000 MB/sec [ 0.111937] 8regs_prefetch: 2052.000 MB/sec [ 0.151970] 32regs : 2830.000 MB/sec [ 0.192000] 32regs_prefetch: 2378.000 MB/sec [ 0.192008] xor: using function: 32regs (2830.000 MB/sec) [ 0.192076] pinctrl core: initialized pinctrl subsystem [ 0.192579] NET: Registered protocol family 16 [ 0.193212] cpuidle: using governor menu [ 0.193742] vdso: 2 pages (1 code @ ffffff8008a56000, 1 data @ ffffff8008df4000) [ 0.193758] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.194211] DMA: preallocated 256 KiB pool for atomic allocations [ 0.223619] reset_zynqmp reset-controller: Xilinx zynqmp reset driver probed [ 0.224192] ARM CCI_400_r1 PMU driver probed [ 0.229124] zynqmp-pinctrl ff180000.pinctrl: zynqmp pinctrl initialized [ 0.237138] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.304247] raid6: int64x1 gen() 402 MB/s [ 0.372184] raid6: int64x1 xor() 445 MB/s [ 0.440231] raid6: int64x2 gen() 687 MB/s [ 0.508308] raid6: int64x2 xor() 603 MB/s [ 0.576357] raid6: int64x4 gen() 1042 MB/s [ 0.644398] raid6: int64x4 xor() 742 MB/s [ 0.712466] raid6: int64x8 gen() 980 MB/s [ 0.780478] raid6: int64x8 xor() 745 MB/s [ 0.848586] raid6: neonx1 gen() 726 MB/s [ 0.916570] raid6: neonx1 xor() 852 MB/s [ 0.984636] raid6: neonx2 gen() 1168 MB/s [ 1.052672] raid6: neonx2 xor() 1207 MB/s [ 1.120740] raid6: neonx4 gen() 1506 MB/s [ 1.188769] raid6: neonx4 xor() 1442 MB/s [ 1.256834] raid6: neonx8 gen() 1651 MB/s [ 1.324862] raid6: neonx8 xor() 1533 MB/s [ 1.324870] raid6: using algorithm neonx8 gen() 1651 MB/s [ 1.324877] raid6: .... xor() 1533 MB/s, rmw enabled [ 1.324885] raid6: using neon recovery algorithm [ 1.326305] SCSI subsystem initialized [ 1.326463] usbcore: registered new interface driver usbfs [ 1.326503] usbcore: registered new interface driver hub [ 1.326549] usbcore: registered new device driver usb [ 1.326614] media: Linux media interface: v0.10 [ 1.326640] Linux video capture interface: v2.00 [ 1.326677] pps_core: LinuxPPS API ver. 1 registered [ 1.326685] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 1.326705] PTP clock support registered [ 1.326731] EDAC MC: Ver: 3.0.0 [ 1.327027] zynqmp-ipi ff9905c0.mailbox: Probed ZynqMP IPI Mailbox driver. [ 1.327172] FPGA manager framework [ 1.327272] fpga-region fpga-full: FPGA Region probed [ 1.327365] Advanced Linux Sound Architecture Driver Initialized. [ 1.327607] Bluetooth: Core ver 2.22 [ 1.327636] NET: Registered protocol family 31 [ 1.327644] Bluetooth: HCI device and connection manager initialized [ 1.327655] Bluetooth: HCI socket layer initialized [ 1.327665] Bluetooth: L2CAP socket layer initialized [ 1.327683] Bluetooth: SCO socket layer initialized [ 1.328209] clocksource: Switched to clocksource arch_sys_counter [ 1.328283] VFS: Disk quotas dquot_6.6.0 [ 1.328327] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.332290] NET: Registered protocol family 2 [ 1.332587] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 1.332797] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 1.333180] TCP: Hash tables configured (established 32768 bind 32768) [ 1.333251] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 1.333328] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 1.333475] NET: Registered protocol family 1 [ 1.333694] RPC: Registered named UNIX socket transport module. [ 1.333703] RPC: Registered udp transport module. [ 1.333710] RPC: Registered tcp transport module. [ 1.333717] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.334083] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 1.334229] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.334862] audit: initializing netlink subsys (disabled) [ 1.335218] audit: type=2000 audit(1.316:1): state=initialized audit_enabled=0 res=1 [ 1.335260] workingset: timestamp_bits=62 max_order=20 bucket_order=0 [ 1.335920] NFS: Registering the id_resolver key type [ 1.335941] Key type id_resolver registered [ 1.335948] Key type id_legacy registered [ 1.335960] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.335981] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.359337] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.359357] io scheduler noop registered [ 1.359365] io scheduler deadline registered [ 1.359385] io scheduler cfq registered (default) [ 1.359393] io scheduler mq-deadline registered [ 1.359401] io scheduler kyber registered [ 1.360002] nwl-pcie fd0e0000.pcie: Link is DOWN [ 1.360044] OF: PCI: host bridge /amba/pcie@fd0e0000 ranges: [ 1.360066] OF: PCI: MEM 0xe0000000..0xefffffff -> 0xe0000000 [ 1.360079] OF: PCI: MEM 0x600000000..0x7ffffffff -> 0x600000000 [ 1.360222] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00 [ 1.360236] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.360247] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 1.360257] pci_bus 0000:00: root bus resource [mem 0x600000000-0x7ffffffff pref] [ 1.360522] pci 0000:00:00.0: PCI bridge to [bus 01-0c] [ 1.361423] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed [ 1.361813] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success [ 1.361979] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success [ 1.362140] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success [ 1.362301] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success [ 1.362461] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success [ 1.362626] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success [ 1.362786] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success [ 1.362951] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success [ 1.363172] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 1.363330] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 1.363486] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 1.363643] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 1.363801] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 1.363960] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 1.364116] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 1.364298] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 1.389330] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.392241] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.396602] brd: module loaded [ 1.399880] loop: module loaded [ 1.400715] ahci-ceva fd0c0000.ahci: couldn't get PHY in node ahci: -517 [ 1.400868] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.401697] m25p80 spi0.0: found n25q512a, expected m25p80 [ 1.401918] m25p80 spi0.0: n25q512a (131072 Kbytes) [ 1.401949] 7 ofpart partitions found on MTD device spi0.0 [ 1.401958] Creating 7 MTD partitions on "spi0.0": [ 1.401969] 0x000000000000-0x000000100000 : "boot" [ 1.402387] 0x000000100000-0x000000140000 : "bootenv" [ 1.402765] 0x000000140000-0x000001740000 : "kernel" [ 1.403148] 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" [ 1.403525] 0x000000100000-0x000000600000 : "qspi-linux" [ 1.403902] 0x000000600000-0x000000620000 : "qspi-device-tree" [ 1.404320] 0x000000620000-0x000000c00000 : "qspi-rootfs" [ 1.405542] libphy: Fixed MDIO Bus: probed [ 1.406485] tun: Universal TUN/TAP device driver, 1.6 [ 1.406614] CAN device driver interface [ 1.408634] macb ff0e0000.ethernet: Not enabling partial store and forward [ 1.409012] libphy: MACB_mii_bus: probed [ 1.410642] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 31 (00:0a:35:00:22:01) [ 1.410658] TI DP83867 ff0e0000.ethernet-ffffffff:0c: attached PHY driver [TI DP83867] (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:0c, irq=POLL) [ 1.411169] usbcore: registered new interface driver asix [ 1.411222] usbcore: registered new interface driver ax88179_178a [ 1.411253] usbcore: registered new interface driver cdc_ether [ 1.411283] usbcore: registered new interface driver net1080 [ 1.411313] usbcore: registered new interface driver cdc_subset [ 1.411343] usbcore: registered new interface driver zaurus [ 1.411387] usbcore: registered new interface driver cdc_ncm [ 1.411644] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 1.412691] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.412702] ehci-pci: EHCI PCI platform driver [ 1.412949] usbcore: registered new interface driver uas [ 1.412987] usbcore: registered new interface driver usb-storage [ 1.413240] mousedev: PS/2 mouse device common for all mice [ 1.413638] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc0 [ 1.413690] i2c /dev entries driver [ 1.414672] IR NEC protocol handler initialized [ 1.414681] IR RC5(x/sz) protocol handler initialized [ 1.414689] IR RC6 protocol handler initialized [ 1.414696] IR JVC protocol handler initialized [ 1.414703] IR Sony protocol handler initialized [ 1.414709] IR SANYO protocol handler initialized [ 1.414716] IR Sharp protocol handler initialized [ 1.414723] IR MCE Keyboard/mouse protocol handler initialized [ 1.414731] IR XMP protocol handler initialized [ 1.415700] usbcore: registered new interface driver uvcvideo [ 1.415710] USB Video Class driver (1.1.1) [ 1.416179] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at ffffff8009175000 with timeout 10s [ 1.416376] Bluetooth: HCI UART driver ver 2.3 [ 1.416386] Bluetooth: HCI UART protocol H4 registered [ 1.416394] Bluetooth: HCI UART protocol BCSP registered [ 1.416421] Bluetooth: HCI UART protocol LL registered [ 1.416429] Bluetooth: HCI UART protocol ATH3K registered [ 1.416437] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.416481] Bluetooth: HCI UART protocol Intel registered [ 1.416490] Bluetooth: HCI UART protocol QCA registered [ 1.416528] usbcore: registered new interface driver bcm203x [ 1.416562] usbcore: registered new interface driver bpa10x [ 1.416595] usbcore: registered new interface driver bfusb [ 1.416627] usbcore: registered new interface driver btusb [ 1.416636] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 1.416685] usbcore: registered new interface driver ath3k [ 1.416812] EDAC MC: ECC not enabled [ 1.416966] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 1.417460] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1199880 KHz [ 1.417514] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1199999 KHz [ 1.417889] sdhci: Secure Digital Host Controller Interface driver [ 1.417898] sdhci: Copyright(c) Pierre Ossman [ 1.417905] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.464359] mmc0: SDHCI controller on ff170000.sdhci [ff170000.sdhci] using ADMA 64-bit [ 1.470382] ledtrig-cpu: registered to indicate activity on CPUs [ 1.470859] usbcore: registered new interface driver usbhid [ 1.470868] usbhid: USB HID core driver [ 1.470875] FPGA DOWNLOAD ---> [ 1.470882] FPGA image file name: xlinx_fpga_firmware.bit [ 1.470946] GPIO INIT FAIL!! [ 1.471076] xlnk xlnk: Major 243 [ 1.471178] xlnk xlnk: xlnk driver loaded [ 1.471189] xlnk xlnk: xlnk_pdev is not null [ 1.474147] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 1.476655] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 1.476852] Netfilter messages via NETLINK v0.30. [ 1.476966] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.477099] Initializing XFRM netlink socket [ 1.477157] NET: Registered protocol family 10 [ 1.477548] Segment Routing with IPv6 [ 1.477592] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.477717] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.478019] NET: Registered protocol family 17 [ 1.478035] NET: Registered protocol family 15 [ 1.478053] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.478067] Ebtables v2.0 registered [ 1.478360] can: controller area network core (rev 20170425 abi 9) [ 1.478396] NET: Registered protocol family 29 [ 1.478410] can: raw protocol (rev 20170425) [ 1.478418] can: broadcast manager protocol (rev 20170425 t) [ 1.478429] can: netlink gateway (rev 20170425) max_hops=1 [ 1.478485] Bluetooth: RFCOMM TTY layer initialized [ 1.478497] Bluetooth: RFCOMM socket layer initialized [ 1.478512] Bluetooth: RFCOMM ver 1.11 [ 1.478522] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.478530] Bluetooth: BNEP filters: protocol multicast [ 1.478540] Bluetooth: BNEP socket layer initialized [ 1.478548] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.478557] Bluetooth: HIDP socket layer initialized [ 1.478670] 9pnet: Installing 9P2000 support [ 1.478690] Key type dns_resolver registered [ 1.482243] registered taskstats version 1 [ 1.482612] Btrfs loaded, crc32c=crc32c-generic [ 1.488130] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 47, base_baud = 6249375) is a xuartps [ 1.603789] mmc0: new high speed SDHC card at address aaaa [ 1.611103] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 1.621133] mmcblk0: p1 p2 [ 3.181153] console [ttyPS0] enabled [ 3.185325] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 48, base_baud = 6249375) is a xuartps [ 3.195914] xilinx-psgtr fd400000.zynqmp_phy: Lane:1 type:8 protocol:4 pll_locked:yes [ 3.204165] PLL: shutdown [ 3.206842] PLL: shutdown [ 3.209758] PLL: enable [ 3.212247] PLL: shutdown [ 3.215596] PLL: enable [ 3.218063] xilinx-dp-snd-codec fd4a0000.zynqmp-display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed [ 3.228649] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed [ 3.236611] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed [ 3.244817] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok [ 3.257182] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok [ 3.269813] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: Xilinx DisplayPort Sound Card probed [ 3.279925] OF: graph: no port node found in /amba/zynqmp-display@fd4a0000 [ 3.286832] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.293366] [drm] No driver support for vblank timestamp query. [ 3.299335] xlnx-drm xlnx-drm.0: bound fd4a0000.zynqmp-display (ops 0xffffff8008b07a28) [ 4.384220] [drm] Cannot find any crtc or sizes [ 4.388844] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.zynqmp-display on minor 0 [ 4.396872] zynqmp-display fd4a0000.zynqmp-display: ZynqMP DisplayPort Subsystem driver probed [ 4.405826] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:3 protocol:2 pll_locked:yes [ 4.423699] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 4.432583] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 4.442864] scsi host0: ahci-ceva [ 4.446299] scsi host1: ahci-ceva [ 4.449642] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 45 [ 4.457482] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 45 [ 4.467041] xilinx-psgtr fd400000.zynqmp_phy: Lane:2 type:0 protocol:3 pll_locked:yes [ 4.477010] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.482430] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 4.490269] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x22010010 [ 4.498915] xhci-hcd xhci-hcd.0.auto: irq 53, io mem 0xfe200000 [ 4.504898] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.511608] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.518813] usb usb1: Product: xHCI Host Controller [ 4.523673] usb usb1: Manufacturer: Linux 4.14.0-xilinx-v2018.2 xhci-hcd [ 4.530355] usb usb1: SerialNumber: xhci-hcd.0.auto [ 4.535498] hub 1-0:1.0: USB hub found [ 4.539187] hub 1-0:1.0: 1 port detected [ 4.543247] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.548661] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 4.556339] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.564444] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 4.571158] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.578362] usb usb2: Product: xHCI Host Controller [ 4.583219] usb usb2: Manufacturer: Linux 4.14.0-xilinx-v2018.2 xhci-hcd [ 4.589906] usb usb2: SerialNumber: xhci-hcd.0.auto [ 4.594996] hub 2-0:1.0: USB hub found [ 4.598682] hub 2-0:1.0: 1 port detected [ 4.603679] pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator [ 4.613564] pca953x 0-0020: interrupt support not compiled in [ 4.619323] pca953x 0-0021: 0-0021 supply vcc not found, using dummy regulator [ 4.629188] pca953x 0-0021: interrupt support not compiled in [ 4.635645] ina2xx 3-0040: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.642354] ina2xx 3-0041: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.649056] ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.655763] ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.662456] ina2xx 3-0044: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.669151] ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.675850] ina2xx 3-0046: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.682549] ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.689247] ina2xx 3-004a: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.695940] ina2xx 3-004b: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.702241] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.707600] ina2xx 4-0040: power monitor ina226 (Rshunt = 2000 uOhm) [ 4.714302] ina2xx 4-0041: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.721007] ina2xx 4-0042: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.727698] ina2xx 4-0043: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.734398] ina2xx 4-0044: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.741098] ina2xx 4-0045: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.747785] ina2xx 4-0046: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.754495] ina2xx 4-0047: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.760801] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.778407] ata2: SATA link down (SStatus 0 SControl 330) [ 4.783779] ata1: SATA link down (SStatus 0 SControl 330) [ 4.811564] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.816407] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.821124] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544 [ 4.828438] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 33 [ 4.835996] at24 7-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write [ 4.842644] i2c i2c-1: Added multiplexed i2c bus 7 [ 4.847587] i2c i2c-1: Added multiplexed i2c bus 8 [ 4.854345] si570 9-005d: registered, current frequency 300000000 Hz [ 4.860651] i2c i2c-1: Added multiplexed i2c bus 9 [ 4.879325] si570 10-005d: registered, current frequency 148500000 Hz [ 4.885718] i2c i2c-1: Added multiplexed i2c bus 10 [ 4.890742] i2c i2c-1: Added multiplexed i2c bus 11 [ 4.895662] i2c i2c-1: Added multiplexed i2c bus 12 [ 4.900577] i2c i2c-1: Added multiplexed i2c bus 13 [ 4.905494] i2c i2c-1: Added multiplexed i2c bus 14 [ 4.910292] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548 [ 4.918156] i2c i2c-1: Added multiplexed i2c bus 15 [ 4.923079] i2c i2c-1: Added multiplexed i2c bus 16 [ 4.928004] i2c i2c-1: Added multiplexed i2c bus 17 [ 4.933228] i2c i2c-1: Added multiplexed i2c bus 18 [ 4.938148] i2c i2c-1: Added multiplexed i2c bus 19 [ 4.943073] i2c i2c-1: Added multiplexed i2c bus 20 [ 4.947994] i2c i2c-1: Added multiplexed i2c bus 21 [ 4.952920] i2c i2c-1: Added multiplexed i2c bus 22 [ 4.957718] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548 [ 4.965291] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 34 [ 4.972504] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.979304] rtc_zynqmp ffa60000.rtc: setting system clock to 2018-12-04 13:07:19 UTC (1543928839) [ 4.988102] of_cfs_init [ 4.990541] of_cfs_init: OK [ 4.994556] OF: Duplicate name in testcase-data, renamed to "duplicate-name#1" [ 5.003586] ### dt-test ### start of unittest - you will see error messages [ 5.010865] OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 [ 5.023057] OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 [ 5.035302] OF: /testcase-data/phandle-tests/consumer-a: could not find phandle [ 5.042592] OF: /testcase-data/phandle-tests/consumer-a: could not find phandle [ 5.049886] OF: /testcase-data/phandle-tests/consumer-a: arguments longer than property [ 5.057864] OF: /testcase-data/phandle-tests/consumer-a: arguments longer than property [ 5.071321] OF: overlay: overlay_is_topmost: #5 clashes #6 @/testcase-data/overlay-node/test-bus/test-unittest8 [ 5.081339] OF: overlay: overlay #5 is not topmost [ 5.088573] i2c i2c-23: Added multiplexed i2c bus 24 [ 5.094443] i2c i2c-23: Added multiplexed i2c bus 25 [ 5.102664] OF: overlay: Failed to apply single node @/testcase-data-2/substation@100/motor-1 [ 5.111125] OF: overlay: apply failed '/testcase-data-2/substation@100' [ 5.117712] ### dt-test ### of_overlay_create() (ret=-22), 2 [ 5.123505] OF: changeset: add_property failed @/symbols/hvac_1 [ 5.129691] OF: Error applying changeset (-17) [ 5.134139] ### dt-test ### of_overlay_create() (ret=-17), 3 [ 5.139764] ### dt-test ### FAIL of_unittest_overlay_high_level():2308 Adding overlay 'overlay_bad_symbol' failed [ 5.150004] ### dt-test ### end of unittest - 190 passed, 1 failed [ 5.156174] clk: Not disabling unused clocks [ 5.160455] ALSA device list: [ 5.163363] #0: DisplayPort monitor [ 5.170847] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 5.437885] EXT4-fs (mmcblk0p2): 2 orphan inodes deleted [ 5.443132] EXT4-fs (mmcblk0p2): recovery complete [ 5.465539] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 5.473580] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 5.483082] devtmpfs: mounted [ 5.486078] Freeing unused kernel memory: 512K [ 5.516222] [drm] Cannot find any crtc or sizes [ 6.058928] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLN -PCRE2 default-hierarchy=hybrid) [ 6.080399] systemd[1]: Detected architecture arm64.

Welcome to PYNQ Linux, based on Ubuntu 18.04!

[ 6.122654] systemd[1]: Set hostname to . [ 6.481468] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does [ 6.498495] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 6.712789] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 6.736275] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 6.752307] systemd[1]: Reached target System Time Synchronized. [ OK ] Reached target System Time Synchronized. [ 6.768465] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 6.784420] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ OK ] Listening on Journal Audit Socket. [ OK ] Reached target Slices. [ OK ] Listening on udev Control Socket. [ OK ] Listening on Journal Socket. Starting Nameserver information manager... Mounting Kernel Debug File System... Starting Restore / save the current clock... Mounting Huge Pages File System... Mounting POSIX Message Queue File System... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Syslog Socket. [ OK ] Listening on udev Kernel Socket. Starting udev Coldplug all Devices... [ OK ] Listening on Journal Socket (/dev/log). Starting Create Static Device Nodes in /dev... Starting Load Kernel Modules... [ OK ] Created slice system-getty.slice. [ OK ] Started ntp-systemd-netif.path. Starting Journal Service... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Local Encrypted Volumes. Starting Remount Root and Kernel File Systems... [ OK ] Mounted Kernel Debug File System. [ OK ] Started Restore / save the current clock. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Nameserver information manager. [ OK ] Reached target Network (Pre). Activating swap /var/swap... Starting Load/Save Random Seed... Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Enable support for additional executable binary formats... Starting udev Kernel Device Manager... Starting Flush Journal to Persistent Storage... [ OK ] Started Load/Save Random Seed. [ 7.381940] Adding 1048572k swap on /var/swap. Priority:-2 extents:9 across:4349948k SS [ OK ] Activated swap /var/swap. [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Enable support for additional executable binary formats. Starting Raise network interfaces... [ OK ] Reached target Swap. [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Reached target Sound Card. [ OK ] Found device /dev/ttyPS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Raise network interfaces. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... Starting Network Name Resolution... [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started resolvconf-pull-resolved.path. [ OK ] Reached target Paths. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Message of the Day. [ OK ] Started Daily apt download activities. [ OK ] Reached target Basic System. Starting System Logging Service... [ OK ] Started Regular background program processing daemon. Starting Jupyter Notebook Server... Starting LSB: Load kernel modules needed to enable cpufreq scaling... Starting PYNQ PL Server... Starting Resize Filesystem on SD card... [ OK ] Started ntp-systemd-netif.service. [ OK ] Started Set the CPU Frequency Scaling governor. [ OK ] Started D-Bus System Message Bus. Starting WPA supplicant... Starting Login Service... [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started Network Name Resolution. [ OK ] Started System Logging Service. [ OK ] Started PYNQ PL Server. [ OK ] Started Resize Filesystem on SD card. [ OK ] Started Login Service. Starting resolvconf-pull-resolved.service... [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started resolvconf-pull-resolved.service. [ OK ] Started WPA supplicant. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started ISC DHCP IPv6 server. [ OK ] Started ISC DHCP IPv4 server. Starting Samba NMB Daemon... Starting Permit User Sessions... [ OK ] Started Unattended Upgrades Shutdown. Starting OpenBSD Secure Shell server... [ OK ] Started Permit User Sessions. [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling. Starting LSB: set CPUFreq kernel parameters... [ OK ] Started Serial Getty on ttyPS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started PYNQ X11 Server. [ OK ] Started LSB: set CPUFreq kernel parameters. [ OK ] Created slice User Slice of root. [ OK ] Started Session c1 of user root. Starting User Manager for UID 0... [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started User Manager for UID 0.

PYNQ Linux, based on Ubuntu 18.04 pynq ttyPS0

pynq login: xilinx (automatic login)

Last login: Tue Dec 4 11:51:12 UTC 2018 on ttyPS0 Welcome to PYNQ Linux, based on Ubuntu 18.04 (GNU/Linux 4.14.0-xilinx-v2018.2 aarch64)

xilinx@pynq:~$ ifconfig -a can0: flags=128 mtu 16 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 10 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 11

eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:0a:35:00:22:01 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 31

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10 loop txqueuelen 1000 (Local Loopback) RX packets 94 bytes 6576 (6.5 KB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 94 bytes 6576 (6.5 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

sit0: flags=128 mtu 1480 sit txqueuelen 1000 (IPv6-in-IPv4) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

  1. When I open jupyter notebook in host PC， it can’t load this overlay as below:

image

Could you tell me how to solve it?

xupsh commented 5 years ago

You need to compile this patch into your kernel following the guide here

hisrg commented 5 years ago

thanks,it has solved.