search

Xilinx / Vitis-AI

Vitis AI is Xilinx’s development stack for AI inference on Xilinx hardware platforms, including both edge devices and Alveo cards.
https://www.xilinx.com/ai
Apache License 2.0
1.49k stars 633 forks source link

meet issue "pip3: command not found" of using "xilinx-zcu102-dpu-v2021.1-v1.4.0.img.gz" #534

Closed chayitw closed 3 years ago

chayitw commented 3 years ago

Hi, When following the step of the "Running on Zynq" tutorial, i download the Petalinux image ( xilinx-zcu102-dpu-v2021.1-v1.4.0.img.gz ) for our target: ZCU-102 and could boot successful. But when i try to install dependency as descripted in "petalinux setup script"(petalinux_setup.sh), i meet the issue: "pip3: command not found". I also have a ZCU-104 board, and try "xilinx-zcu104-dpu-v2021.1-v1.4.0.img.gz", it work well.

Any suggestion is appreciated! Thanks, -chayi

The boot info is as below:

Xilinx Zynq MP First Stage Boot Loader Release 2021.1 Jun 6 2021 - 07:07:32 NOTICE: ATF running on XCZU9EG/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: v2.4(release):v1.1-7609-g851523ea2 NOTICE: BL31: Built : 08:27:07, Apr 28 2021

U-Boot 2021.01 (Jun 01 2021 - 11:54:06 +0000)

Model: ZynqMP ZCU102 Rev1.0 Board: Xilinx ZynqMP DRAM: 4 GiB PMUFW: v1.1 EL Level: EL2 Chip ID: zu9eg NAND: 0 MiB MMC: mmc@ff170000: 0 Loading Environment from FAT... *** Warning - bad CRC, using default environment

In: serial Out: serial Err: serial Bootmode: LVL_SHFT_SD_MODE1 Reset reason: EXTERNAL Net: ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot.scr 2597 bytes read in 12 ms (210.9 KiB/s)

Executing script at 20000000

Trying to load boot images from mmc0 27589120 bytes read in 2041 ms (12.9 MiB/s) 56499 bytes read in 16 ms (3.4 MiB/s)

Flattened Device Tree blob at 00100000

Booting using the fdt blob at 0x100000 Loading Device Tree to 000000007dcff000, end 000000007dd0fcb2 ... OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.0-xilinx-v2021.1 (oe-user@oe-host) (aarch64-xi linx-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Fri Jun 4 15:5 7:16 UTC 2021 [ 0.000000] Machine model: ZynqMP ZCU102 Rev1.0 [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] printk: bootconsole [cdns0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 1536 MiB at 0x000000001dc00000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fefffff] [ 0.000000] node 0: [mem 0x0000000800000000-0x000000087fffffff] [ 0.000000] Zeroed struct page in unavailable ranges: 256 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000087fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 30 pages/cpu s84248 r8192 d30440 u122880 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031940 [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_un used root=/dev/mmcblk0p2 rw rootwait cma=1536M [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes , linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000019c00000-0x000000001dc0000 0] (64MB) [ 0.000000] Memory: 2446236K/4193280K available (15808K kernel code, 1982K rw data, 4328K rodata, 4736K init, 604K bss, 174180K reserved, 1572864K cma-reserve d) [ 0.000000] ftrace: allocating 48776 entries in 191 pages [ 0.000000] ftrace: allocated 191 pages with 7 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jif fies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] irq-xilinx: mismatch in kind-of-intr param [ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@80020000: num_irq=32, sw_irq=0, edge=0x1 [ 0.000000] random: get_random_bytes called from start_kernel+0x38c/0x594 wit h crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 100.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171024e7e0, max_idle_ns: 440795205315 ns [ 0.000004] sched_clock: 56 bits at 100MHz, resolution 10ns, wraps every 4398 046511100ns [ 0.008444] Console: colour dummy device 80x25 [ 0.012483] Calibrating delay loop (skipped), value calculated using timer fr equency.. 200.00 BogoMIPS (lpj=400000) [ 0.022840] pid_max: default: 32768 minimum: 301 [ 0.027581] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, line ar) [ 0.034787] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.043681] rcu: Hierarchical SRCU implementation. [ 0.047808] EFI services will not be available. [ 0.051981] smp: Bringing up secondary CPUs ... [ 0.056721] Detected VIPT I-cache on CPU1 [ 0.056761] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.057187] Detected VIPT I-cache on CPU2 [ 0.057211] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.057610] Detected VIPT I-cache on CPU3 [ 0.057634] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.057686] smp: Brought up 1 node, 4 CPUs [ 0.091779] SMP: Total of 4 processors activated. [ 0.096451] CPU features: detected: 32-bit EL0 Support [ 0.101555] CPU features: detected: CRC32 instructions [ 0.106698] CPU: All CPU(s) started at EL2 [ 0.110736] alternatives: patching kernel code [ 0.116351] devtmpfs: initialized [ 0.124796] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns [ 0.128893] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.175165] pinctrl core: initialized pinctrl subsystem [ 0.175697] DMI not present or invalid. [ 0.178757] NET: Registered protocol family 16 [ 0.184120] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.190079] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic al locations [ 0.197890] audit: initializing netlink subsys (disabled) [ 0.203366] audit: type=2000 audit(0.144:1): state=initialized audit_enabled= 0 res=1 [ 0.210939] cpuidle: using governor menu [ 0.214891] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.221617] ASID allocator initialised with 65536 entries [ 0.227038] Serial: AMBA PL011 UART driver [ 0.259090] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.260149] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.266820] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.273493] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 1.326947] cryptd: max_cpu_qlen set to 1000 [ 1.352298] DRBG: Continuing without Jitter RNG [ 1.432975] raid6: neonx8 gen() 2137 MB/s [ 1.501032] raid6: neonx8 xor() 1594 MB/s [ 1.569107] raid6: neonx4 gen() 2184 MB/s [ 1.637166] raid6: neonx4 xor() 1562 MB/s [ 1.705238] raid6: neonx2 gen() 2072 MB/s [ 1.773295] raid6: neonx2 xor() 1436 MB/s [ 1.841368] raid6: neonx1 gen() 1770 MB/s [ 1.909429] raid6: neonx1 xor() 1219 MB/s [ 1.977492] raid6: int64x8 gen() 1437 MB/s [ 2.045560] raid6: int64x8 xor() 771 MB/s [ 2.113632] raid6: int64x4 gen() 1598 MB/s [ 2.181692] raid6: int64x4 xor() 821 MB/s [ 2.249764] raid6: int64x2 gen() 1393 MB/s [ 2.317820] raid6: int64x2 xor() 746 MB/s [ 2.385905] raid6: int64x1 gen() 1030 MB/s [ 2.453958] raid6: int64x1 xor() 517 MB/s [ 2.453996] raid6: using algorithm neonx4 gen() 2184 MB/s [ 2.457947] raid6: .... xor() 1562 MB/s, rmw enabled [ 2.462883] raid6: using neon recovery algorithm [ 2.468006] iommu: Default domain type: Translated [ 2.472551] SCSI subsystem initialized [ 2.476173] usbcore: registered new interface driver usbfs [ 2.481509] usbcore: registered new interface driver hub [ 2.486784] usbcore: registered new device driver usb [ 2.491831] mc: Linux media interface: v0.10 [ 2.496035] videodev: Linux video capture interface: v2.00 [ 2.501515] EDAC MC: Ver: 3.0.0 [ 2.504962] zynqmp-ipi-mbox mailbox@ff990400: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.513262] FPGA manager framework [ 2.516559] Advanced Linux Sound Architecture Driver Initialized. [ 2.522786] Bluetooth: Core ver 2.22 [ 2.526039] NET: Registered protocol family 31 [ 2.530441] Bluetooth: HCI device and connection manager initialized [ 2.536758] Bluetooth: HCI socket layer initialized [ 2.541600] Bluetooth: L2CAP socket layer initialized [ 2.546623] Bluetooth: SCO socket layer initialized [ 2.551734] clocksource: Switched to clocksource arch_sys_counter [ 3.419859] VFS: Disk quotas dquot_6.6.0 [ 3.419949] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 3.429775] NET: Registered protocol family 2 [ 3.430187] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 3276 8 bytes, linear) [ 3.437837] TCP established hash table entries: 32768 (order: 6, 262144 bytes , linear) [ 3.445865] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linea r) [ 3.453331] TCP: Hash tables configured (established 32768 bind 32768) [ 3.459491] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 3.466153] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 3.473334] NET: Registered protocol family 1 [ 3.477833] RPC: Registered named UNIX socket transport module. [ 3.483387] RPC: Registered udp transport module. [ 3.488049] RPC: Registered tcp transport module. [ 3.492721] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.499742] PCI: CLS 0 bytes, default 64 [ 3.530071] Initialise system trusted keyrings [ 3.530205] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 3.536063] NFS: Registering the id_resolver key type [ 3.540316] Key type id_resolver registered [ 3.544466] Key type id_legacy registered [ 3.548454] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.555115] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 3.598760] NET: Registered protocol family 38 [ 3.598804] xor: measuring software checksum speed [ 3.606500] 8regs : 2362 MB/sec [ 3.610162] 32regs : 2797 MB/sec [ 3.615115] arm64_neon : 2372 MB/sec [ 3.615291] xor: using function: 32regs (2797 MB/sec) [ 3.620316] Key type asymmetric registered [ 3.624379] Asymmetric key parser 'x509' registered [ 3.629245] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 3.636577] io scheduler mq-deadline registered [ 3.641073] io scheduler kyber registered [ 3.647049] ps_pcie_dma init() [ 3.676460] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.678321] Serial: AMBA driver [ 3.682924] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 3.691074] brd: module loaded [ 3.695690] loop: module loaded [ 3.696651] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.701119] libphy: Fixed MDIO Bus: probed [ 3.704999] tun: Universal TUN/TAP device driver, 1.6 [ 3.708775] CAN device driver interface [ 3.713292] usbcore: registered new interface driver asix [ 3.717902] usbcore: registered new interface driver ax88179_178a [ 3.723932] usbcore: registered new interface driver cdc_ether [ 3.729726] usbcore: registered new interface driver net1080 [ 3.735345] usbcore: registered new interface driver cdc_subset [ 3.741227] usbcore: registered new interface driver zaurus [ 3.746773] usbcore: registered new interface driver cdc_ncm [ 3.753334] usbcore: registered new interface driver uas [ 3.757677] usbcore: registered new interface driver usb-storage [ 3.764282] rtc_zynqmp ffa60000.rtc: registered as rtc0 [ 3.768822] rtc_zynqmp ffa60000.rtc: setting system clock to 2021-01-30T22:11 :22 UTC (1612044682) [ 3.777677] i2c /dev entries driver [ 3.782809] usbcore: registered new interface driver uvcvideo [ 3.786794] USB Video Class driver (1.1.1) [ 3.791902] Bluetooth: HCI UART driver ver 2.3 [ 3.795265] Bluetooth: HCI UART protocol H4 registered [ 3.800378] Bluetooth: HCI UART protocol BCSP registered [ 3.805667] Bluetooth: HCI UART protocol LL registered [ 3.810754] Bluetooth: HCI UART protocol ATH3K registered [ 3.816128] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 3.822383] Bluetooth: HCI UART protocol Intel registered [ 3.827721] Bluetooth: HCI UART protocol QCA registered [ 3.832922] usbcore: registered new interface driver bcm203x [ 3.838549] usbcore: registered new interface driver bpa10x [ 3.844082] usbcore: registered new interface driver bfusb [ 3.849529] usbcore: registered new interface driver btusb [ 3.854993] usbcore: registered new interface driver ath3k [ 3.860484] EDAC MC: ECC not enabled [ 3.864106] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac control ler zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 3.876483] sdhci: Secure Digital Host Controller Interface driver [ 3.882208] sdhci: Copyright(c) Pierre Ossman [ 3.886528] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.892541] ledtrig-cpu: registered to indicate activity on CPUs [ 3.898133] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 3.904558] zynqmp_firmware_probe Platform Management API v1.1 [ 3.910318] zynqmp_firmware_probe Trustzone version v1.0 [ 3.945752] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: zynqmp pinctrl i nitialized [ 3.991361] alg: No test for xilinx-zynqmp-aes (zynqmp-aes) [ 3.991436] zynqmp_aes firmware:zynqmp-firmware:zynqmp-aes: AES Successfully Registered [ 3.999460] alg: No test for xilinx-keccak-384 (zynqmp-keccak-384) [ 4.005620] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa) [ 4.011096] usbcore: registered new interface driver usbhid [ 4.016470] usbhid: USB HID core driver [ 4.023127] ARM CCI_400_r1 PMU driver probed [ 4.023614] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 4.031396] usbcore: registered new interface driver snd-usb-audio [ 4.037969] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 4.045241] Initializing XFRM netlink socket [ 4.048892] NET: Registered protocol family 10 [ 4.053681] Segment Routing with IPv6 [ 4.057012] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.063097] NET: Registered protocol family 17 [ 4.067171] NET: Registered protocol family 15 [ 4.071578] can: controller area network core [ 4.075925] NET: Registered protocol family 29 [ 4.080308] can: raw protocol [ 4.083240] can: broadcast manager protocol [ 4.087401] can: netlink gateway - max_hops=1 [ 4.091822] Bluetooth: RFCOMM TTY layer initialized [ 4.096577] Bluetooth: RFCOMM socket layer initialized [ 4.101684] Bluetooth: RFCOMM ver 1.11 [ 4.105393] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.110666] Bluetooth: BNEP filters: protocol multicast [ 4.115859] Bluetooth: BNEP socket layer initialized [ 4.120785] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.126670] Bluetooth: HIDP socket layer initialized [ 4.131739] 9pnet: Installing 9P2000 support [ 4.135856] Key type dns_resolver registered [ 4.140296] registered taskstats version 1 [ 4.144148] Loading compiled-in X.509 certificates [ 4.149898] Btrfs loaded, crc32c=crc32c-generic [ 4.162750] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 51, base_baud = 6249999) is a xuartps [ 4.171773] printk: console [ttyPS0] enabled [ 4.171773] printk: console [ttyPS0] enabled [ 4.176068] printk: bootconsole [cdns0] disabled [ 4.176068] printk: bootconsole [cdns0] disabled [ 4.185745] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 52, base_baud = 6249999) is a xuartps [ 4.198927] of-fpga-region fpga-full: FPGA Region probed [ 4.205998] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success [ 4.213185] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success [ 4.220369] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success [ 4.227550] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success [ 4.234735] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success [ 4.241918] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success [ 4.249094] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success [ 4.256289] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success [ 4.263539] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 4.270724] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 4.277905] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 4.285084] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 4.292263] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 4.299444] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 4.306625] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 4.313804] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 4.321214] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 4.329682] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regul ator [ 4.337241] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regula tor [ 4.345358] spi-nor spi0.0: found mt25qu512a, expected m25p80 [ 4.351761] spi-nor spi0.0: trying to lock already unlocked area [ 4.357764] spi-nor spi0.0: mt25qu512a (131072 Kbytes) [ 4.362921] 3 fixed-partitions partitions found on MTD device spi0.0 [ 4.369278] Creating 3 MTD partitions on "spi0.0": [ 4.374065] 0x000000000000-0x000001e00000 : "boot" [ 4.379695] 0x000001e00000-0x000001e40000 : "bootenv" [ 4.385512] 0x000001e40000-0x000004240000 : "kernel" [ 4.393672] macb ff0e0000.ethernet: Not enabling partial store and forward [ 4.401223] libphy: MACB_mii_bus: probed [ 4.405882] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e 0000 irq 39 (00:0a:35:05:07:d2) [ 4.416132] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 4.422705] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 4.429245] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 4.435856] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 4.463526] pca953x 0-0020: supply vcc not found, using dummy regulator [ 4.470213] pca953x 0-0020: using no AI [ 4.474767] pca953x 0-0021: supply vcc not found, using dummy regulator [ 4.481435] pca953x 0-0021: using no AI [ 4.494980] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.506634] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.522705] random: fast init done [ 4.565438] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.570354] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.575150] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca95 44 [ 4.582482] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 41 [ 4.590229] at24 6-0054: supply vcc not found, using dummy regulator [ 4.597130] at24 6-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write [ 4.603862] i2c i2c-1: Added multiplexed i2c bus 6 [ 4.610141] si5341 7-0036: Chip: 5341 Grade: 1 Rev: 1 [ 4.647934] i2c i2c-1: Added multiplexed i2c bus 7 [ 4.655584] si570 8-005d: registered, current frequency 300000000 Hz [ 4.661973] i2c i2c-1: Added multiplexed i2c bus 8 [ 4.681762] si570 9-005d: registered, current frequency 148500000 Hz [ 4.688154] i2c i2c-1: Added multiplexed i2c bus 9 [ 4.693187] si5324 10-0069: si5328 probed [ 4.760101] si5324 10-0069: si5328 probe successful [ 4.765016] i2c i2c-1: Added multiplexed i2c bus 10 [ 4.770015] i2c i2c-1: Added multiplexed i2c bus 11 [ 4.775019] i2c i2c-1: Added multiplexed i2c bus 12 [ 4.780023] i2c i2c-1: Added multiplexed i2c bus 13 [ 4.784902] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pc a9548 [ 4.792890] i2c i2c-1: Added multiplexed i2c bus 14 [ 4.797897] i2c i2c-1: Added multiplexed i2c bus 15 [ 4.802909] i2c i2c-1: Added multiplexed i2c bus 16 [ 4.807923] i2c i2c-1: Added multiplexed i2c bus 17 [ 4.812931] i2c i2c-1: Added multiplexed i2c bus 18 [ 4.817938] i2c i2c-1: Added multiplexed i2c bus 19 [ 4.822952] i2c i2c-1: Added multiplexed i2c bus 20 [ 4.827966] i2c i2c-1: Added multiplexed i2c bus 21 [ 4.832841] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pc a9548 [ 4.840433] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 42 [ 4.850574] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60 s [ 4.858087] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer with timeout 10 s [ 4.868940] zynqmp-display fd4a0000.display: vtc bridge property not present [ 4.877850] xilinx-dp-snd-codec fd4a0000.display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed [ 4.888023] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PC M probed [ 4.896154] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PC M probed [ 4.899984] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 4.904793] xilinx-dp-snd-card fd4a0000.display:zynqmp_dp_snd_card: ASoC: no DMI vendor name! [ 4.920534] xilinx-dp-snd-card fd4a0000.display:zynqmp_dp_snd_card: Xilinx Di splayPort Sound Card probed [ 4.930140] OF: graph: no port node found in /axi/display@fd4a0000 [ 4.936679] xlnx-drm xlnx-drm.0: bound fd4a0000.display (ops 0xffff80001106a6 70) [ 4.979124] mmc0: new high speed SDHC card at address aaaa [ 4.985014] mmcblk0: mmc0:aaaa SC32G 29.7 GiB [ 4.993412] mmcblk0: p1 p2 [ 6.023765] zynqmp-display fd4a0000.display: [drm] Cannot find any crtc or si zes [ 6.031419] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.display on min or 0 [ 6.038920] zynqmp-display fd4a0000.display: ZynqMP DisplayPort Subsystem dri ver probed [ 6.047336] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regul ator [ 6.054886] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regula tor [ 6.062352] ahci-ceva fd0c0000.ahci: supply target not found, using dummy reg ulator [ 6.080257] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0 x3 impl platform mode [ 6.089221] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fb s pio slum part ccc sds apst [ 6.099649] scsi host0: ahci-ceva [ 6.103291] scsi host1: ahci-ceva [ 6.106736] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x1 00 irq 49 [ 6.114647] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x1 80 irq 49 [ 6.123250] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.128755] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus nu mber 1 [ 6.136519] xhci-hcd xhci-hcd.1.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x0000000002010810 [ 6.145931] xhci-hcd xhci-hcd.1.auto: irq 90, io mem 0xfe200000 [ 6.152089] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 5.10 [ 6.160357] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 6.167577] usb usb1: Product: xHCI Host Controller [ 6.172448] usb usb1: Manufacturer: Linux 5.10.0-xilinx-v2021.1 xhci-hcd [ 6.179145] usb usb1: SerialNumber: xhci-hcd.1.auto [ 6.184338] hub 1-0:1.0: USB hub found [ 6.188108] hub 1-0:1.0: 1 port detected [ 6.192242] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.197733] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus nu mber 2 [ 6.205397] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 6.212062] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bc dDevice= 5.10 [ 6.220326] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 6.227545] usb usb2: Product: xHCI Host Controller [ 6.232414] usb usb2: Manufacturer: Linux 5.10.0-xilinx-v2021.1 xhci-hcd [ 6.239110] usb usb2: SerialNumber: xhci-hcd.1.auto [ 6.244237] hub 2-0:1.0: USB hub found [ 6.248005] hub 2-0:1.0: 1 port detected [ 6.255089] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 6.262187] of_cfs_init [ 6.264650] of_cfs_init: OK [ 6.267594] cfg80211: Loading compiled-in X.509 certificates for regulatory d atabase [ 6.402917] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 6.409453] clk: Not disabling unused clocks [ 6.413967] ALSA device list: [ 6.416925] #0: DisplayPort monitor [ 6.420877] platform regulatory.0: Direct firmware load for regulatory.db fai led with error -2 [ 6.429494] cfg80211: failed to load regulatory.db [ 6.433959] ata1: SATA link down (SStatus 0 SControl 330) [ 6.439710] ata2: SATA link down (SStatus 0 SControl 330) [ 6.574419] EXT4-fs (mmcblk0p2): recovery complete [ 6.582074] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 6.590204] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 6.599355] devtmpfs: mounted [ 6.605721] Freeing unused kernel memory: 4736K [ 6.610340] Run /sbin/init as init process INIT: version 2.97 booting Starting udev [ 7.116683] udevd[263]: starting version 3.2.9 [ 7.131771] zynqmp-display fd4a0000.display: [drm] Cannot find any crtc or si zes [ 7.144160] random: udevd: uninitialized urandom read (16 bytes read) [ 7.151118] random: udevd: uninitialized urandom read (16 bytes read) [ 7.157587] random: udevd: uninitialized urandom read (16 bytes read) [ 7.213839] udevd[264]: starting eudev-3.2.9 [ 7.344874] zocl: loading out-of-tree module taints kernel. [ 7.353962] [drm] Probing for xlnx,zocl [ 7.358254] zocl-drm amba_pl@0:zyxclmm_drm: IRQ index 32 not found [ 7.364676] [drm] FPGA programming device pcap founded. [ 7.369925] [drm] PR Isolation addr 0x0 [ 7.383384] [drm] Initialized zocl 0.0.0 00000 for amba_pl@0:zyxclmm_drm on m inor 1 [ 8.019559] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 8.129550] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Starting tcf-agent: OK

PetaLinux 2021.1 xilinx-zcu102-2021_1 ttyPS0

root@xilinx-zcu102-2021_1:~# D-BUS per-session daemon address is: unix:abstract=/tmp/dbus-UYgDwZQgYC,guid=4b8a1061a101fe6bcd1b9fcd6015d998 matchbox: Cant find a keycode for keysym 269025056 matchbox: ignoring key shortcut XF86Calendar=!$contacts

matchbox: Cant find a keycode for keysym 2809 matchbox: ignoring key shortcut telephone=!$dates

matchbox: Cant find a keycode for keysym 269025050 matchbox: ignoring key shortcut XF86Start=!matchbox-remote -desktop

[settings daemon] Forking. run with -n to prevent fork dbus-daemon[882]: Activating service name='org.a11y.atspi.Registry' requested by ':1.0' (uid=0 pid=878 comm="matchbox-panel --start-applets showdesktop,windows") dbus-daemon[882]: Successfully activated service 'org.a11y.atspi.Registry' SpiRegistry daemon is running with well-known name - org.a11y.atspi.Registry

(matchbox-desktop:877): WARNING : 22:11:38.516: Error loading icon: Icon 'terminal' not present in theme Sato

root@xilinx-zcu102-2021_1:~# root@xilinx-zcu102-2021_1:~# root@xilinx-zcu102-2021_1:~# root@xilinx-zcu102-2021_1:~# pip3 -sh: pip3: command not found root@xilinx-zcu102-2021_1:~# root@xilinx-zcu102-2021_1:~# locate pip3 root@xilinx-zcu102-2021_1:~#

runner42195 commented 3 years ago

I meet the same issue, did you figure out it.

qianglin-xlnx commented 3 years ago

Hi @chayitw Thank you for your feedback. We will check this issue and feedback to you.

tianfang-fafafa commented 3 years ago

hi @chayitw first, I don't know who release "petalinux setup script"(petalinux_setup.sh). In a developer's view, the zcu104 supports package gstreamer-vcu-examples which depends on pip3, so the pip3 would be installed autometically. So the zcu102 would have no pip3. can you please try "dnf install python3-pip" ?

tianfang-fafafa commented 3 years ago

hi @runner42195 , please look into previous reply

chayitw commented 3 years ago

hi @tianfang-fafafa , i have holiday until 9/14, and no board in hand. Thanks for your suggestion, i will try it when back to my office.

hi @qianglin-xlnx, thanks for your kindly reply also ^ ^

( Happy Moon Festival ^ ^ )

chayitw commented 3 years ago

hi @tianfang-fafafa, I just try "dnf install python3-pip" on ZCU102, and meet the below problem:

1. Firstly, i meet the issue about "404" for the download path such like that:
    Errors during downloading metadata for repository 'oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpeg':
  1. Secondly, it could download after above adjust but meet the issue about "No match for argument: python3-pip":

root@xilinx-zcu102-2021_1:/etc/yum.repos.d# dnf install python3-pip OE Remote Repo: sswreleases rel-v2021.1 generic rpm noarch 6.2 kB/s | 3.0 kB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm aarch64 7.1 kB/s | 3.0 kB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp 6.7 kB/s | 3.0 kB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpeg 187 kB/s | 294 kB 00:01 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpev 400 kB/s | 296 kB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpdr 6.0 kB/s | 11 kB 00:01 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpcg 3.7 kB/s | 5.6 kB 00:01 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp_generic 6.2 kB/s | 3.0 kB 00:00 No match for argument: python3-pip Error: Unable to find a match: python3-pip

Need your suggestion to solve this issue, thanks.

br, --chayi

tianfang-fafafa commented 3 years ago

@chayitw ok. I will reply you once solving this issue

tianfang-fafafa commented 3 years ago

@chayitw can you please try baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53/ ? my board can't access to Internent in my environment

chayitw commented 3 years ago

hi @tianfang-fafafa, thanks! It seems work after change the baseurl to be "http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53/".

The detail info. is as below: ( just need 2 steps suggested by @tianfang-fafafa )

  1. change the baseurl of "/etc/yum.repos.d/oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm.repo":

_root@xilinx-zcu102-2021_1:/etc/yum.repos.d# cat /etc/yum.repos.d/oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm.repo [oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm noarch baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-aarch64] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm aarch64 baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmp] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpeg] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpeg baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpev] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpev baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpdr] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpdr baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpcg] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpcg baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmp_generic] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp_generic baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53 gpgcheck=0_

  1. using "dnf install python3-pip" to install pip3:

_root@xilinx-zcu102-2021_1:/etc/yum.repos.d# dnf install python3-pip OE Remote Repo: sswreleases rel-v2021.1 generic rpm noarch 467 kB/s | 3.8 MB 00:08 OE Remote Repo: sswreleases rel-v2021.1 generic rpm aarch64 18 MB/s | 3.8 MB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp 16 MB/s | 3.8 MB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpeg 18 MB/s | 3.8 MB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpev 18 MB/s | 3.8 MB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpdr 1.4 MB/s | 3.8 MB 00:02 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpcg 15 MB/s | 3.8 MB 00:00 OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp_generic 18 MB/s | 3.8 MB 00:00 Last metadata expiration check: 0:00:05 ago on Wed Feb 10 03:58:09 2021. Dependencies resolved.

Package Architecture Version Repository Size

Installing: python3-pip cortexa72_cortexa53 20.0.2-r0.0 oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch 1.6 M Installing dependencies: python3-pkg-resources cortexa72_cortexa53 49.6.0-r0.0 oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch 203 k python3-setuptools cortexa72_cortexa53 49.6.0-r0.0 oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch 684 k Installing weak dependencies: python3-pip-lic cortexa72_cortexa53 20.0.2-r0.0 oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch 7.4 k python3-setuptools-lic cortexa72_cortexa53 49.6.0-r0.0 oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch 7.4 k

Transaction Summary

Install 5 Packages

Total download size: 2.5 M Installed size: 11 M Is this ok [y/N]: y Downloading Packages: (1/5): python3-pip-lic-20.0.2-r0.0.cortexa72_cortexa53.rpm 16 kB/s | 7.4 kB 00:00 (2/5): python3-pkg-resources-49.6.0-r0.0.cortexa72_cortexa53.rpm 216 kB/s | 203 kB 00:00 (3/5): python3-setuptools-lic-49.6.0-r0.0.cortexa72_cortexa53.rpm 17 kB/s | 7.4 kB 00:00 (4/5): python3-pip-20.0.2-r0.0.cortexa72_cortexa53.rpm 1.1 MB/s | 1.6 MB 00:01 (5/5): python3-setuptools-49.6.0-r0.0.cortexa72_cortexa53.rpm 591 kB/s | 684 kB 00:01

Total 1.5 MB/s | 2.5 MB 00:01 Running transaction check Transaction check succeeded. Running transaction test Transaction test succeeded. Running transaction Preparing : 1/1 Installing : python3-setuptools-lic-49.6.0-r0.0.cortexa72_cortexa53 1/5 Installing : python3-pkg-resources-49.6.0-r0.0.cortexa72_cortexa53 2/5 Installing : python3-setuptools-49.6.0-r0.0.cortexa72_cortexa53 3/5 Installing : python3-pip-lic-20.0.2-r0.0.cortexa72_cortexa53 4/5 Installing : python3-pip-20.0.2-r0.0.cortexa72_cortexa53 5/5 Verifying : python3-pip-20.0.2-r0.0.cortexa72_cortexa53 1/5 Verifying : python3-pip-lic-20.0.2-r0.0.cortexa72_cortexa53 2/5 Verifying : python3-pkg-resources-49.6.0-r0.0.cortexa72_cortexa53 3/5 Verifying : python3-setuptools-49.6.0-r0.0.cortexa72_cortexa53 4/5 Verifying : python3-setuptools-lic-49.6.0-r0.0.cortexa72_cortexa53 5/5

Installed: python3-pip-20.0.2-r0.0.cortexa72_cortexa53 python3-pip-lic-20.0.2-r0.0.cortexa72_cortexa53 python3-pkg-resources-49.6.0-r0.0.cortexa72_cortexa53 python3-setuptools-49.6.0-r0.0.cortexa72_cortexa53 python3-setuptools-lic-49.6.0-r0.0.cortexa72_cortexa53

Complete!_

tianfang-fafafa commented 3 years ago

@chayitw hi，can you please provide me the default /etc/yum.repos.d/oe-xxx.repo ?

chayitw commented 3 years ago

@tianfang-fafafa, thanks, Yes, of course, the default "/etc/yum.repos.d/oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm.repo" is as below:

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-noarch] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm noarch baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/noarch gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-aarch64] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm aarch64 baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/aarch64 gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmp] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/zynqmp gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpeg] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpeg baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/zynqmpeg gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpev] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpev baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/zynqmpev gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpdr] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpdr baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/zynqmpdr gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmpcg] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmpcg baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/zynqmpcg gpgcheck=0

[oe-remote-repo-sswreleases-rel-v2021.1-generic-rpm-zynqmp_generic] name=OE Remote Repo: sswreleases rel-v2021.1 generic rpm zynqmp_generic baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/zynqmp_generic gpgcheck=0

tianfang-fafafa commented 3 years ago

@chayitw thanks

chayitw commented 3 years ago

@tianfang-fafafa, welcome, very thanks for your help ^ ^

( *Because this issue has been solved by @tianfang-fafafa, and help by @qianglin-xlnx (thanks ^ ^), I close it. )

runner42195 commented 3 years ago

Is there a new xilinx-zcu102-dpu-v2021.1-v1.4.0.img.gz with the pip3 installed?

tianfang-fafafa commented 3 years ago

hi, there is no new xilinx-zcu102-dpu-v2021.1-v1.4.0.img.gz with the pip3 installed. can you please try install pip3 via dnf command? replace line "baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/aarch64" with "baseurl=http://petalinux.xilinx.com/sswreleases/rel-v2021.1/generic/rpm/cortexa72_cortexa53" first. And this repo issue will be fixed in next release