Zubax opengrab_epm_v3 issues

Zubax / opengrab_epm_v3

OpenGrab Electropermanent Magnet

https://zubax.com/epm

GNU General Public License v3.0

32 stars 19 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Update drwatson

#58 pavel-kirienko opened 3 years ago
0
Smallsuperfast

#57 ctech4285 opened 3 years ago
0
Link to the hardware sources is broken.

#56 nophead opened 4 years ago
2
J9 Pin numbers in documentation pictures are incorrect

#55 ctech4285 opened 6 years ago
1
decreasing Ip increases charger eff by 5% points

#54 AndreasJochum closed 7 years ago
0
Add distinct blink partner for low Vin during switching

#53 ctech4285 opened 7 years ago
2
Catastrophic failure mode possible on different hardware

#52 ctech4285 opened 7 years ago
1
Hardware pwm capture

#51 ctech4285 opened 7 years ago
0
Added support for external button, RXD on J9

#50 ctech4285 closed 7 years ago
0
Remove dead branches

#49 pavel-kirienko opened 7 years ago
4
Low side Thyristors need to fire first, reduces dV/dt stress

#48 ctech4285 closed 7 years ago
0
Updated model and drawing, PDF, IGS and STEP

#47 ctech4285 closed 7 years ago
0
Delete EPM_V3_simple.SLDDRW

#46 ctech4285 closed 7 years ago
0
Delete EPM_V3_simple.PDF

#45 ctech4285 closed 7 years ago
0
Delete EPM_V3.SLDPRT

#44 ctech4285 closed 7 years ago
0
Spelling, earlier

#43 ctech4285 closed 7 years ago
1
Update setup.sh

#42 ctech4285 closed 7 years ago
0
Measurement of main capacitor after discharge returned bad result

#41 ctech4285 closed 8 years ago
0
ADC seems to hickup every now and then

#40 ctech4285 closed 8 years ago
2
Updated for R5C

#39 ctech4285 closed 8 years ago
0
Print build date over UART at boot

#38 ctech4285 closed 8 years ago
0
Cleanup and print supply_volatage_mV_min during switching if below 4.8V

#37 ctech4285 closed 8 years ago
0
almost perfect

#36 ctech4285 closed 8 years ago
2
cleanup, couple of fixes

#35 ctech4285 closed 8 years ago
0
cleaner implementation of better cycle limiting

#34 ctech4285 closed 8 years ago
0
Better cycle limiting

#33 ctech4285 closed 8 years ago
0
ReducedCurrentVoltage_mV missing for ProDropper config

#32 ctech4285 closed 8 years ago
0
Documenation update

#31 ctech4285 closed 8 years ago
0
Documenation update

#30 ctech4285 closed 8 years ago
0
Degauss fix

#29 ctech4285 closed 8 years ago
1
Customer was able to kill his EPM when turning on constantly

#28 ctech4285 closed 8 years ago
1
Magnetometer

#27 pavel-kirienko opened 8 years ago
0
Reduce current consumption when Vin is < 4.8V

#26 ctech4285 closed 8 years ago
0
Migrate to JST GH

#25 pavel-kirienko closed 8 years ago
2
Dip test

#24 ctech4285 closed 8 years ago
1
fixed missing end line character

#23 ctech4285 closed 8 years ago
0
Vin measurement incorrect after boot

#22 ctech4285 closed 8 years ago
3
ProDropper support

#21 pavel-kirienko closed 8 years ago
0
Test Dipswitch

#20 ctech4285 closed 8 years ago
4
Drwatson: added a flag to skip testing and only sign; fixes #18

#19 pavel-kirienko closed 8 years ago
1
Change Drwatsons behavior

#18 ctech4285 closed 8 years ago
1
Command rate limiting not working when going on->off->on->off.....

#17 ctech4285 closed 8 years ago
4
Drwatson, test first then sing

#16 ctech4285 closed 8 years ago
0
Drwatson fixes

#15 pavel-kirienko closed 8 years ago
1
When button is presses repeatedly and fast ~200ms the EPM does funky things

#14 ctech4285 closed 8 years ago
5
Untangle status LED from button in the next rev

#13 ctech4285 opened 8 years ago
3
Funky behavior when UAVCAN and PWM or button is used at the same time

#12 ctech4285 closed 8 years ago
1
Funky behavior when UAVCAN and PWM or button is used at the same time

#11 ctech4285 closed 8 years ago
1
Properly handle the DIP switch

#10 pavel-kirienko closed 8 years ago
0
Turn off command, first 3 cycles in the array need to be skipped if the magnet is coming from the Off position

#9 ctech4285 closed 8 years ago
2