my usb meter only shows .00 but anything like my ftdi usb2serial even with led on shows .00 any and all devices that show .00 will not work;
usb 1-1: new full-speed USB device number 9 using xhci-hcd
[ 1744.708325] usb 1-1: device descriptor read/64, error -71
[ 1744.943858] usb 1-1: device descriptor read/64, error -71
[ 1745.180184] usb 1-1: new full-speed USB device number 10 using xhci-hcd
[ 1745.307877] usb 1-1: device descriptor read/64, error -71
[ 1745.544013] usb 1-1: device descriptor read/64, error -71
[ 1745.657037] usb usb1-port1: attempt power cycle
[ 1746.316452] usb 1-1: new full-speed USB device number 11 using xhci-hcd
[ 1746.316715] usb 1-1: Device not responding to setup address.
[ 1746.524701] usb 1-1: Device not responding to setup address.
[ 1746.733083] usb 1-1: device not accepting address 11, error -71
[ 1746.860112] usb 1-1: new full-speed USB device number 12 using xhci-hcd
[ 1746.860416] usb 1-1: Device not responding to setup address.
[ 1747.072251] usb 1-1: Device not responding to setup address.
[ 1747.280475] usb 1-1: device not accepting address 12, error -71
[ 1747.281296] usb usb1-port1: unable to enumerate USB device
if an idle device jumps between .00 and .01 50 percent of the time, then it will enumerate 50 percent of the time. If i simply add a small load to these devices with a resistor or a inline usb vol/amp meter then they work fine.
im using the 5.7 patches ive tried the interconnect dts patches (dunno if that even makes sense) i know that enabling wifi in dts would break my right side usb port until recent patches. i may try with wifi and panel removed from dts and the min max regulator settings that come with those too and see if its any different.
my usb meter only shows .00 but anything like my ftdi usb2serial even with led on shows .00 any and all devices that show .00 will not work; usb 1-1: new full-speed USB device number 9 using xhci-hcd [ 1744.708325] usb 1-1: device descriptor read/64, error -71 [ 1744.943858] usb 1-1: device descriptor read/64, error -71 [ 1745.180184] usb 1-1: new full-speed USB device number 10 using xhci-hcd [ 1745.307877] usb 1-1: device descriptor read/64, error -71 [ 1745.544013] usb 1-1: device descriptor read/64, error -71 [ 1745.657037] usb usb1-port1: attempt power cycle [ 1746.316452] usb 1-1: new full-speed USB device number 11 using xhci-hcd [ 1746.316715] usb 1-1: Device not responding to setup address. [ 1746.524701] usb 1-1: Device not responding to setup address. [ 1746.733083] usb 1-1: device not accepting address 11, error -71 [ 1746.860112] usb 1-1: new full-speed USB device number 12 using xhci-hcd [ 1746.860416] usb 1-1: Device not responding to setup address. [ 1747.072251] usb 1-1: Device not responding to setup address. [ 1747.280475] usb 1-1: device not accepting address 12, error -71 [ 1747.281296] usb usb1-port1: unable to enumerate USB device
if an idle device jumps between .00 and .01 50 percent of the time, then it will enumerate 50 percent of the time. If i simply add a small load to these devices with a resistor or a inline usb vol/amp meter then they work fine. im using the 5.7 patches ive tried the interconnect dts patches (dunno if that even makes sense) i know that enabling wifi in dts would break my right side usb port until recent patches. i may try with wifi and panel removed from dts and the min max regulator settings that come with those too and see if its any different.