search

albfan / miraclecast

Connect external monitors to your system via Wifi-Display specification also known as Miracast
Other
3.66k stars 407 forks source link

support for thinkpad x230 Intel Corporation Centrino Advanced-N 6205 #376

Closed ghost closed 4 years ago

ghost commented 4 years ago

Hi, res/test-hardware-capabilities.sh returns Sorry, wlp3s0 do not support P2P but iw list does return P2P stuff. I was wondering if miraclecast would work on my machine

Including dmesg, firmware and iw outputs

firmware

driver: iwlwifi
version: 5.3.0-46-generic
firmware-version: 18.168.6.1
expansion-rom-version: 
bus-info: 0000:03:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no

iw

Wiphy phy0
    max # scan SSIDs: 20
    max scan IEs length: 195 bytes
    max # sched scan SSIDs: 0
    max # match sets: 0
    max # scan plans: 1
    max scan plan interval: -1
    max scan plan iterations: 0
    Retry short limit: 7
    Retry long limit: 4
    Coverage class: 0 (up to 0m)
    Device supports RSN-IBSS.
    Supported Ciphers:
        * WEP40 (00-0f-ac:1)
        * WEP104 (00-0f-ac:5)
        * TKIP (00-0f-ac:2)
        * CCMP-128 (00-0f-ac:4)
        * CCMP-256 (00-0f-ac:10)
        * GCMP-128 (00-0f-ac:8)
        * GCMP-256 (00-0f-ac:9)
    Available Antennas: TX 0 RX 0
    Supported interface modes:
         * IBSS
         * managed
         * AP
         * AP/VLAN
         * monitor
    Band 1:
        Capabilities: 0x107e
            HT20/HT40
            SM Power Save disabled
            RX Greenfield
            RX HT20 SGI
            RX HT40 SGI
            No RX STBC
            Max AMSDU length: 3839 bytes
            DSSS/CCK HT40
        Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
        Minimum RX AMPDU time spacing: 4 usec (0x05)
        HT Max RX data rate: 300 Mbps
        HT TX/RX MCS rate indexes supported: 0-15
        Bitrates (non-HT):
            * 1.0 Mbps
            * 2.0 Mbps (short preamble supported)
            * 5.5 Mbps (short preamble supported)
            * 11.0 Mbps (short preamble supported)
            * 6.0 Mbps
            * 9.0 Mbps
            * 12.0 Mbps
            * 18.0 Mbps
            * 24.0 Mbps
            * 36.0 Mbps
            * 48.0 Mbps
            * 54.0 Mbps
        Frequencies:
            * 2412 MHz [1] (15.0 dBm)
            * 2417 MHz [2] (15.0 dBm)
            * 2422 MHz [3] (15.0 dBm)
            * 2427 MHz [4] (15.0 dBm)
            * 2432 MHz [5] (15.0 dBm)
            * 2437 MHz [6] (15.0 dBm)
            * 2442 MHz [7] (15.0 dBm)
            * 2447 MHz [8] (15.0 dBm)
            * 2452 MHz [9] (15.0 dBm)
            * 2457 MHz [10] (15.0 dBm)
            * 2462 MHz [11] (15.0 dBm)
            * 2467 MHz [12] (15.0 dBm) (no IR)
            * 2472 MHz [13] (15.0 dBm) (no IR)
    Band 2:
        Capabilities: 0x107e
            HT20/HT40
            SM Power Save disabled
            RX Greenfield
            RX HT20 SGI
            RX HT40 SGI
            No RX STBC
            Max AMSDU length: 3839 bytes
            DSSS/CCK HT40
        Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
        Minimum RX AMPDU time spacing: 4 usec (0x05)
        HT Max RX data rate: 300 Mbps
        HT TX/RX MCS rate indexes supported: 0-15
        Bitrates (non-HT):
            * 6.0 Mbps
            * 9.0 Mbps
            * 12.0 Mbps
            * 18.0 Mbps
            * 24.0 Mbps
            * 36.0 Mbps
            * 48.0 Mbps
            * 54.0 Mbps
        Frequencies:
            * 5180 MHz [36] (15.0 dBm) (no IR)
            * 5200 MHz [40] (15.0 dBm) (no IR)
            * 5220 MHz [44] (15.0 dBm) (no IR)
            * 5240 MHz [48] (15.0 dBm) (no IR)
            * 5260 MHz [52] (15.0 dBm) (no IR, radar detection)
            * 5280 MHz [56] (15.0 dBm) (no IR, radar detection)
            * 5300 MHz [60] (15.0 dBm) (no IR, radar detection)
            * 5320 MHz [64] (15.0 dBm) (no IR, radar detection)
            * 5500 MHz [100] (15.0 dBm) (no IR, radar detection)
            * 5520 MHz [104] (15.0 dBm) (no IR, radar detection)
            * 5540 MHz [108] (15.0 dBm) (no IR, radar detection)
            * 5560 MHz [112] (15.0 dBm) (no IR, radar detection)
            * 5580 MHz [116] (15.0 dBm) (no IR, radar detection)
            * 5600 MHz [120] (15.0 dBm) (no IR, radar detection)
            * 5620 MHz [124] (15.0 dBm) (no IR, radar detection)
            * 5640 MHz [128] (15.0 dBm) (no IR, radar detection)
            * 5660 MHz [132] (15.0 dBm) (no IR, radar detection)
            * 5680 MHz [136] (15.0 dBm) (no IR, radar detection)
            * 5700 MHz [140] (15.0 dBm) (no IR, radar detection)
            * 5745 MHz [149] (13.0 dBm) (no IR)
            * 5765 MHz [153] (13.0 dBm) (no IR)
            * 5785 MHz [157] (13.0 dBm) (no IR)
            * 5805 MHz [161] (13.0 dBm) (no IR)
            * 5825 MHz [165] (13.0 dBm) (no IR)
    Supported commands:
         * new_interface
         * set_interface
         * new_key
         * start_ap
         * new_station
         * new_mpath
         * set_mesh_config
         * set_bss
         * authenticate
         * associate
         * deauthenticate
         * disassociate
         * join_ibss
         * join_mesh
         * set_tx_bitrate_mask
         * frame
         * frame_wait_cancel
         * set_wiphy_netns
         * set_channel
         * set_wds_peer
         * probe_client
         * set_noack_map
         * register_beacons
         * start_p2p_device
         * set_mcast_rate
         * connect
         * disconnect
         * set_qos_map
         * set_multicast_to_unicast
    Supported TX frame types:
         * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
         * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
    Supported RX frame types:
         * IBSS: 0x40 0xb0 0xc0 0xd0
         * managed: 0x40 0xd0
         * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
         * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
         * mesh point: 0xb0 0xc0 0xd0
         * P2P-client: 0x40 0xd0
         * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
         * P2P-device: 0x40 0xd0
    WoWLAN support:
         * wake up on disconnect
         * wake up on magic packet
         * wake up on pattern match, up to 20 patterns of 16-128 bytes,
           maximum packet offset 0 bytes
         * can do GTK rekeying
         * wake up on GTK rekey failure
         * wake up on EAP identity request
         * wake up on rfkill release
    software interface modes (can always be added):
         * AP/VLAN
         * monitor
    valid interface combinations:
         * #{ managed } <= 1, #{ AP } <= 1,
           total <= 2, #channels <= 1, STA/AP BI must match
         * #{ managed } <= 2,
           total <= 2, #channels <= 1
    HT Capability overrides:
         * MCS: ff ff ff ff ff ff ff ff ff ff
         * maximum A-MSDU length
         * supported channel width
         * short GI for 40 MHz
         * max A-MPDU length exponent
         * min MPDU start spacing
    Device supports TX status socket option.
    Device supports HT-IBSS.
    Device supports SAE with AUTHENTICATE command
    Device supports scan flush.
    Device supports per-vif TX power setting
    Driver supports full state transitions for AP/GO clients
    Driver supports a userspace MPM
    Device supports static SMPS
    Device supports dynamic SMPS
    Device supports configuring vdev MAC-addr on create.
    Supported extended features:
        * [ RRM ]: RRM
        * [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
        * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
        * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211

dmesg

[    0.000000] microcode: microcode updated early to revision 0x21, date = 2019-02-13
[    0.000000] Linux version 5.3.0-46-generic (buildd@lgw01-amd64-003) (gcc version 9.2.1 20191008 (Ubuntu 9.2.1-9ubuntu2)) #38-Ubuntu SMP Fri Mar 27 17:37:05 UTC 2020 (Ubuntu 5.3.0-46.38-generic 5.3.18)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-5.3.0-46-generic root=UUID=42206f77-9075-4324-989c-1a4074059dbf ro quiet splash vt.handoff=7
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Hygon HygonGenuine
[    0.000000]   Centaur CentaurHauls
[    0.000000]   zhaoxin   Shanghai  
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008ffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x00000000000bffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040005000-0x00000000d0fcefff] usable
[    0.000000] BIOS-e820: [mem 0x00000000d0fcf000-0x00000000d11d0fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000d11d1000-0x00000000d684efff] usable
[    0.000000] BIOS-e820: [mem 0x00000000d684f000-0x00000000dae9efff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000dae9f000-0x00000000daf9efff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000daf9f000-0x00000000daffefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000dafff000-0x00000000daffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000db000000-0x00000000df9fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f80f8000-0x00000000f80f8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021e5fffff] usable
[    0.000000] BIOS-e820: [mem 0x000000021e600000-0x000000021e7fffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] e820: update [mem 0xd1c3c018-0xd1c4c057] usable ==> usable
[    0.000000] e820: update [mem 0xd1c3c018-0xd1c4c057] usable ==> usable
[    0.000000] e820: update [mem 0xd1c2b018-0xd1c3b657] usable ==> usable
[    0.000000] e820: update [mem 0xd1c2b018-0xd1c3b657] usable ==> usable
[    0.000000] extended physical RAM map:
[    0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000008ffff] usable
[    0.000000] reserve setup_data: [mem 0x0000000000090000-0x00000000000bffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] reserve setup_data: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000020200000-0x0000000040003fff] usable
[    0.000000] reserve setup_data: [mem 0x0000000040004000-0x0000000040004fff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000040005000-0x00000000d0fcefff] usable
[    0.000000] reserve setup_data: [mem 0x00000000d0fcf000-0x00000000d11d0fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000d11d1000-0x00000000d1c2b017] usable
[    0.000000] reserve setup_data: [mem 0x00000000d1c2b018-0x00000000d1c3b657] usable
[    0.000000] reserve setup_data: [mem 0x00000000d1c3b658-0x00000000d1c3c017] usable
[    0.000000] reserve setup_data: [mem 0x00000000d1c3c018-0x00000000d1c4c057] usable
[    0.000000] reserve setup_data: [mem 0x00000000d1c4c058-0x00000000d684efff] usable
[    0.000000] reserve setup_data: [mem 0x00000000d684f000-0x00000000dae9efff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000dae9f000-0x00000000daf9efff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x00000000daf9f000-0x00000000daffefff] ACPI data
[    0.000000] reserve setup_data: [mem 0x00000000dafff000-0x00000000daffffff] usable
[    0.000000] reserve setup_data: [mem 0x00000000db000000-0x00000000df9fffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000f80f8000-0x00000000f80f8fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000021e5fffff] usable
[    0.000000] reserve setup_data: [mem 0x000000021e600000-0x000000021e7fffff] reserved
[    0.000000] efi: EFI v2.31 by Lenovo
[    0.000000] efi:  ACPI 2.0=0xdaffe014  ACPI=0xdaffe000  SMBIOS=0xdae9e000 
[    0.000000] secureboot: Secure boot disabled
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: LENOVO 2325J67/2325J67, BIOS G2ETB4WW (2.74 ) 11/14/2018
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2494.192 MHz processor
[    0.004404] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.004407] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.004421] last_pfn = 0x21e600 max_arch_pfn = 0x400000000
[    0.004430] MTRR default type: uncachable
[    0.004431] MTRR fixed ranges enabled:
[    0.004434]   00000-9FFFF write-back
[    0.004435]   A0000-BFFFF uncachable
[    0.004437]   C0000-FFFFF write-protect
[    0.004439] MTRR variable ranges enabled:
[    0.004442]   0 base 0FFC00000 mask FFFC00000 write-protect
[    0.004444]   1 base 000000000 mask F80000000 write-back
[    0.004446]   2 base 080000000 mask FC0000000 write-back
[    0.004448]   3 base 0C0000000 mask FE0000000 write-back
[    0.004449]   4 base 0DC000000 mask FFC000000 uncachable
[    0.004451]   5 base 0DB000000 mask FFF000000 uncachable
[    0.004453]   6 base 100000000 mask F00000000 write-back
[    0.004455]   7 base 200000000 mask FE0000000 write-back
[    0.004456]   8 base 21F000000 mask FFF000000 uncachable
[    0.004458]   9 base 21E800000 mask FFF800000 uncachable
[    0.005230] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.005529] last_pfn = 0xdb000 max_arch_pfn = 0x400000000
[    0.028084] check: Scanning 1 areas for low memory corruption
[    0.028095] BRK [0x1c4e01000, 0x1c4e01fff] PGTABLE
[    0.028098] BRK [0x1c4e02000, 0x1c4e02fff] PGTABLE
[    0.028100] BRK [0x1c4e03000, 0x1c4e03fff] PGTABLE
[    0.028194] BRK [0x1c4e04000, 0x1c4e04fff] PGTABLE
[    0.028197] BRK [0x1c4e05000, 0x1c4e05fff] PGTABLE
[    0.028425] BRK [0x1c4e06000, 0x1c4e06fff] PGTABLE
[    0.028702] BRK [0x1c4e07000, 0x1c4e07fff] PGTABLE
[    0.028703] BRK [0x1c4e08000, 0x1c4e08fff] PGTABLE
[    0.028923] BRK [0x1c4e09000, 0x1c4e09fff] PGTABLE
[    0.028954] BRK [0x1c4e0a000, 0x1c4e0afff] PGTABLE
[    0.029079] BRK [0x1c4e0b000, 0x1c4e0bfff] PGTABLE
[    0.029227] BRK [0x1c4e0c000, 0x1c4e0cfff] PGTABLE
[    0.029964] RAMDISK: [mem 0x3d253000-0x3fffdfff]
[    0.029981] ACPI: Early table checksum verification disabled
[    0.029987] ACPI: RSDP 0x00000000DAFFE014 000024 (v02 LENOVO)
[    0.029994] ACPI: XSDT 0x00000000DAFFE170 0000BC (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030005] ACPI: FACP 0x00000000DAFE5000 00010C (v05 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030017] ACPI: DSDT 0x00000000DAFE7000 011383 (v01 LENOVO TP-G2    00002740 INTL 20061109)
[    0.030023] ACPI: FACS 0x00000000DAF5A000 000040
[    0.030029] ACPI: SLIC 0x00000000DAFFD000 000176 (v01 LENOVO TP-G2    00002740 PTL  00000001)
[    0.030035] ACPI: TCPA 0x00000000DAFFC000 000032 (v02 PTL    LENOVO   06040000 LNVO 00000001)
[    0.030041] ACPI: SSDT 0x00000000DAFFB000 000408 (v01 LENOVO TP-SSDT2 00000200 INTL 20061109)
[    0.030047] ACPI: SSDT 0x00000000DAFFA000 000033 (v01 LENOVO TP-SSDT1 00000100 INTL 20061109)
[    0.030053] ACPI: SSDT 0x00000000DAFF9000 0007A8 (v01 LENOVO SataAhci 00001000 INTL 20061109)
[    0.030059] ACPI: HPET 0x00000000DAFE3000 000038 (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030065] ACPI: APIC 0x00000000DAFE2000 000098 (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030071] ACPI: MCFG 0x00000000DAFE1000 00003C (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030077] ACPI: ECDT 0x00000000DAFE0000 000052 (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030083] ACPI: FPDT 0x00000000DAFDF000 000064 (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030089] ACPI: ASF! 0x00000000DAFE6000 0000A5 (v32 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030095] ACPI: UEFI 0x00000000DAFDE000 00003E (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030101] ACPI: UEFI 0x00000000DAFDD000 000042 (v01 PTL    COMBUF   00000001 PTL  00000001)
[    0.030107] ACPI: POAT 0x00000000DAFDC000 000055 (v03 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030113] ACPI: SSDT 0x00000000DAFDB000 000C37 (v01 PmRef  Cpu0Ist  00003000 INTL 20061109)
[    0.030119] ACPI: SSDT 0x00000000DAFDA000 000A83 (v01 PmRef  CpuPm    00003000 INTL 20061109)
[    0.030125] ACPI: UEFI 0x00000000DAFD9000 000292 (v01 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030131] ACPI: DBG2 0x00000000DAFD8000 0000E9 (v00 LENOVO TP-G2    00002740 PTL  00000002)
[    0.030147] ACPI: DMI detected: Lenovo ThinkPad X230
[    0.030152] ACPI: Local APIC address 0xfee00000
[    0.030317] No NUMA configuration found
[    0.030319] Faking a node at [mem 0x0000000000000000-0x000000021e5fffff]
[    0.030341] NODE_DATA(0) allocated [mem 0x21e5d0000-0x21e5fafff]
[    0.030965] Zone ranges:
[    0.030966]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.030969]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.030971]   Normal   [mem 0x0000000100000000-0x000000021e5fffff]
[    0.030973]   Device   empty
[    0.030974] Movable zone start for each node
[    0.030981] Early memory node ranges
[    0.030983]   node   0: [mem 0x0000000000001000-0x000000000008ffff]
[    0.030985]   node   0: [mem 0x0000000000100000-0x000000001fffffff]
[    0.030987]   node   0: [mem 0x0000000020200000-0x0000000040003fff]
[    0.030988]   node   0: [mem 0x0000000040005000-0x00000000d0fcefff]
[    0.030990]   node   0: [mem 0x00000000d11d1000-0x00000000d684efff]
[    0.030991]   node   0: [mem 0x00000000dafff000-0x00000000daffffff]
[    0.030992]   node   0: [mem 0x0000000100000000-0x000000021e5fffff]
[    0.031842] Zeroed struct page in unavailable ranges: 46628 pages
[    0.031845] Initmem setup node 0 [mem 0x0000000000001000-0x000000021e5fffff]
[    0.031848] On node 0 totalpages: 2050524
[    0.031851]   DMA zone: 64 pages used for memmap
[    0.031852]   DMA zone: 91 pages reserved
[    0.031854]   DMA zone: 3983 pages, LIFO batch:0
[    0.031972]   DMA32 zone: 13650 pages used for memmap
[    0.031974]   DMA32 zone: 873549 pages, LIFO batch:63
[    0.058930]   Normal zone: 18328 pages used for memmap
[    0.058933]   Normal zone: 1172992 pages, LIFO batch:63
[    0.090921] Reserving Intel graphics memory at [mem 0xdba00000-0xdf9fffff]
[    0.091411] ACPI: PM-Timer IO Port: 0x408
[    0.091416] ACPI: Local APIC address 0xfee00000
[    0.091430] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.091432] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.091449] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.091454] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.091457] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.091459] ACPI: IRQ0 used by override.
[    0.091461] ACPI: IRQ9 used by override.
[    0.091466] Using ACPI (MADT) for SMP configuration information
[    0.091469] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[    0.091478] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[    0.091517] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.091520] PM: Registered nosave memory: [mem 0x00090000-0x000bffff]
[    0.091522] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
[    0.091525] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[    0.091528] PM: Registered nosave memory: [mem 0x40004000-0x40004fff]
[    0.091531] PM: Registered nosave memory: [mem 0xd0fcf000-0xd11d0fff]
[    0.091534] PM: Registered nosave memory: [mem 0xd1c2b000-0xd1c2bfff]
[    0.091538] PM: Registered nosave memory: [mem 0xd1c3b000-0xd1c3bfff]
[    0.091539] PM: Registered nosave memory: [mem 0xd1c3c000-0xd1c3cfff]
[    0.091542] PM: Registered nosave memory: [mem 0xd1c4c000-0xd1c4cfff]
[    0.091546] PM: Registered nosave memory: [mem 0xd684f000-0xdae9efff]
[    0.091547] PM: Registered nosave memory: [mem 0xdae9f000-0xdaf9efff]
[    0.091548] PM: Registered nosave memory: [mem 0xdaf9f000-0xdaffefff]
[    0.091551] PM: Registered nosave memory: [mem 0xdb000000-0xdf9fffff]
[    0.091553] PM: Registered nosave memory: [mem 0xdfa00000-0xf80f7fff]
[    0.091554] PM: Registered nosave memory: [mem 0xf80f8000-0xf80f8fff]
[    0.091555] PM: Registered nosave memory: [mem 0xf80f9000-0xfed1bfff]
[    0.091556] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.091557] PM: Registered nosave memory: [mem 0xfed20000-0xffffffff]
[    0.091561] [mem 0xdfa00000-0xf80f7fff] available for PCI devices
[    0.091563] Booting paravirtualized kernel on bare hardware
[    0.091568] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.091582] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[    0.092081] percpu: Embedded 54 pages/cpu s184320 r8192 d28672 u262144
[    0.092095] pcpu-alloc: s184320 r8192 d28672 u262144 alloc=1*2097152
[    0.092097] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.092160] Built 1 zonelists, mobility grouping on.  Total pages: 2018391
[    0.092161] Policy zone: Normal
[    0.092164] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.3.0-46-generic root=UUID=42206f77-9075-4324-989c-1a4074059dbf ro quiet splash vt.handoff=7
[    0.093186] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.093620] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.093804] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.100944] Calgary: detecting Calgary via BIOS EBDA area
[    0.100946] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.136670] Memory: 7837252K/8202096K available (14339K kernel code, 2387K rwdata, 4724K rodata, 2676K init, 5044K bss, 364844K reserved, 0K cma-reserved)
[    0.136947] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.136968] Kernel/User page tables isolation: enabled
[    0.136997] ftrace: allocating 43582 entries in 171 pages
[    0.171889] rcu: Hierarchical RCU implementation.
[    0.171892] rcu:     RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
[    0.171893]  Tasks RCU enabled.
[    0.171895] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.171896] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.179321] NR_IRQS: 524544, nr_irqs: 488, preallocated irqs: 16
[    0.179758] random: crng done (trusting CPU's manufacturer)
[    0.179807] vt handoff: transparent VT on vt#7
[    0.179822] Console: colour dummy device 80x25
[    0.179829] printk: console [tty0] enabled
[    0.179860] ACPI: Core revision 20190703
[    0.180204] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.180227] APIC: Switch to symmetric I/O mode setup
[    0.180305] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.180918] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.200232] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x23f3cb57cf7, max_idle_ns: 440795259173 ns
[    0.200239] Calibrating delay loop (skipped), value calculated using timer frequency.. 4988.38 BogoMIPS (lpj=9976768)
[    0.200244] pid_max: default: 32768 minimum: 301
[    0.209236] LSM: Security Framework initializing
[    0.209258] Yama: becoming mindful.
[    0.209339] AppArmor: AppArmor initialized
[    0.209431] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.209455] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.209793] *** VALIDATE proc ***
[    0.209897] *** VALIDATE cgroup1 ***
[    0.209900] *** VALIDATE cgroup2 ***
[    0.209990] mce: CPU0: Thermal monitoring enabled (TM1)
[    0.210009] process: using mwait in idle threads
[    0.210014] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[    0.210016] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[    0.210023] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.210026] Spectre V2 : Mitigation: Full generic retpoline
[    0.210027] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.210028] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.210031] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.210032] Spectre V2 : User space: Mitigation: STIBP via seccomp and prctl
[    0.210034] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.210040] MDS: Mitigation: Clear CPU buffers
[    0.210388] Freeing SMP alternatives memory: 36K
[    0.215188] TSC deadline timer enabled
[    0.215193] smpboot: CPU0: Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz (family: 0x6, model: 0x3a, stepping: 0x9)
[    0.215446] Performance Events: PEBS fmt1+, IvyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[    0.215457] ... version:                3
[    0.215458] ... bit width:              48
[    0.215459] ... generic registers:      4
[    0.215460] ... value mask:             0000ffffffffffff
[    0.215462] ... max period:             00007fffffffffff
[    0.215463] ... fixed-purpose events:   3
[    0.215464] ... event mask:             000000070000000f
[    0.215538] rcu: Hierarchical SRCU implementation.
[    0.216235] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.216235] smp: Bringing up secondary CPUs ...
[    0.216235] x86: Booting SMP configuration:
[    0.216235] .... node  #0, CPUs:      #1
[    0.219041] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.
[    0.219041]  #2 #3
[    0.227067] smp: Brought up 1 node, 4 CPUs
[    0.227067] smpboot: Max logical packages: 2
[    0.227067] smpboot: Total of 4 processors activated (19953.53 BogoMIPS)
[    0.228681] devtmpfs: initialized
[    0.228681] x86/mm: Memory block size: 128MB
[    0.229912] PM: Registering ACPI NVS region [mem 0xdae9f000-0xdaf9efff] (1048576 bytes)
[    0.229912] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.229912] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.229912] pinctrl core: initialized pinctrl subsystem
[    0.229912] PM: RTC time: 16:12:06, date: 2020-04-17
[    0.229912] NET: Registered protocol family 16
[    0.229912] audit: initializing netlink subsys (disabled)
[    0.229912] audit: type=2000 audit(1587139926.048:1): state=initialized audit_enabled=0 res=1
[    0.229912] EISA bus registered
[    0.229912] cpuidle: using governor ladder
[    0.229912] cpuidle: using governor menu
[    0.229912] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.229912] ACPI: bus type PCI registered
[    0.229912] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.232263] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.232286] PCI: not using MMCONFIG
[    0.232288] PCI: Using configuration type 1 for base access
[    0.232355] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.232967] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.235007] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.240420] ACPI: Added _OSI(Module Device)
[    0.240422] ACPI: Added _OSI(Processor Device)
[    0.240423] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.240425] ACPI: Added _OSI(Processor Aggregator Device)
[    0.240427] ACPI: Added _OSI(Linux-Dell-Video)
[    0.240429] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.240430] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.240432] ACPI: Deleted _OSI(Windows 2012)
[    0.275702] ACPI: 6 ACPI AML tables successfully acquired and loaded
[    0.277248] ACPI: EC: EC started
[    0.277249] ACPI: EC: interrupt blocked
[    0.279105] ACPI: \: Used as first EC
[    0.279108] ACPI: \: GPE=0x11, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[    0.279109] ACPI: EC: Boot ECDT EC used to handle transactions
[    0.279693] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.286901] ACPI: Dynamic OEM Table Load:
[    0.286920] ACPI: SSDT 0xFFFF8B4654902000 000A01 (v01 PmRef  Cpu0Cst  00003001 INTL 20061109)
[    0.289278] ACPI: Dynamic OEM Table Load:
[    0.289291] ACPI: SSDT 0xFFFF8B465490D800 000303 (v01 PmRef  ApIst    00003000 INTL 20061109)
[    0.291115] ACPI: Dynamic OEM Table Load:
[    0.291126] ACPI: SSDT 0xFFFF8B4654AE8E00 000119 (v01 PmRef  ApCst    00003000 INTL 20061109)
[    0.294580] ACPI: Interpreter enabled
[    0.294623] ACPI: (supports S0 S3 S4 S5)
[    0.294625] ACPI: Using IOAPIC for interrupt routing
[    0.294683] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.296106] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in ACPI motherboard resources
[    0.296124] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.296893] ACPI: Enabled 6 GPEs in block 00 to 3F
[    0.304596] ACPI: Power Resource [PUBS] (on)
[    0.304911] acpi PNP0C0A:01: ACPI dock station (docks/bays count: 1)
[    0.307283] acpi LNXIOBAY:00: ACPI dock station (docks/bays count: 2)
[    0.311921] acpi IBM0079:00: ACPI dock station (docks/bays count: 3)
[    0.313140] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[    0.313374] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.313597] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.313817] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.314035] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.314253] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.314472] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.314691] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[    0.314892] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
[    0.314901] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.315325] acpi PNP0A08:00: _OSC: platform does not support [SHPCHotplug PCIeCapability LTR]
[    0.315520] acpi PNP0A08:00: _OSC: not requesting control; platform does not support [PCIeCapability]
[    0.315524] acpi PNP0A08:00: _OSC: OS requested [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR]
[    0.315527] acpi PNP0A08:00: _OSC: platform willing to grant [PCIeHotplug PME AER]
[    0.315529] acpi PNP0A08:00: _OSC failed (AE_SUPPORT); disabling ASPM
[    0.315952] PCI host bridge to bus 0000:00
[    0.315957] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.315959] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.315962] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.315964] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfebfffff window]
[    0.315966] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed4bfff window]
[    0.315969] pci_bus 0000:00: root bus resource [bus 00-3f]
[    0.315988] pci 0000:00:00.0: [8086:0154] type 00 class 0x060000
[    0.316164] pci 0000:00:02.0: [8086:0166] type 00 class 0x030000
[    0.316183] pci 0000:00:02.0: reg 0x10: [mem 0xf0000000-0xf03fffff 64bit]
[    0.316193] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.316201] pci 0000:00:02.0: reg 0x20: [io  0x6000-0x603f]
[    0.316223] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.316411] pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
[    0.316458] pci 0000:00:14.0: reg 0x10: [mem 0xf2520000-0xf252ffff 64bit]
[    0.316600] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.316755] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
[    0.316802] pci 0000:00:16.0: reg 0x10: [mem 0xf2535000-0xf253500f 64bit]
[    0.316945] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.317099] pci 0000:00:19.0: [8086:1502] type 00 class 0x020000
[    0.317139] pci 0000:00:19.0: reg 0x10: [mem 0xf2500000-0xf251ffff]
[    0.317153] pci 0000:00:19.0: reg 0x14: [mem 0xf253b000-0xf253bfff]
[    0.317166] pci 0000:00:19.0: reg 0x18: [io  0x6080-0x609f]
[    0.317284] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    0.317448] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
[    0.317486] pci 0000:00:1a.0: reg 0x10: [mem 0xf253a000-0xf253a3ff]
[    0.317646] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.317803] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
[    0.317847] pci 0000:00:1b.0: reg 0x10: [mem 0xf2530000-0xf2533fff 64bit]
[    0.318000] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.318152] pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
[    0.318349] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.318522] pci 0000:00:1c.1: [8086:1e12] type 01 class 0x060400
[    0.318717] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.318888] pci 0000:00:1c.2: [8086:1e14] type 01 class 0x060400
[    0.319081] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.319260] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
[    0.319300] pci 0000:00:1d.0: reg 0x10: [mem 0xf2539000-0xf25393ff]
[    0.319455] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.319606] pci 0000:00:1f.0: [8086:1e55] type 00 class 0x060100
[    0.319914] pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
[    0.319957] pci 0000:00:1f.2: reg 0x10: [io  0x60a8-0x60af]
[    0.319972] pci 0000:00:1f.2: reg 0x14: [io  0x60b4-0x60b7]
[    0.319989] pci 0000:00:1f.2: reg 0x18: [io  0x60a0-0x60a7]
[    0.320005] pci 0000:00:1f.2: reg 0x1c: [io  0x60b0-0x60b3]
[    0.320021] pci 0000:00:1f.2: reg 0x20: [io  0x6060-0x607f]
[    0.320038] pci 0000:00:1f.2: reg 0x24: [mem 0xf2538000-0xf25387ff]
[    0.320137] pci 0000:00:1f.2: PME# supported from D3hot
[    0.320293] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
[    0.320333] pci 0000:00:1f.3: reg 0x10: [mem 0xf2534000-0xf25340ff 64bit]
[    0.320378] pci 0000:00:1f.3: reg 0x20: [io  0xefa0-0xefbf]
[    0.320752] pci 0000:02:00.0: [1180:e823] type 00 class 0x088001
[    0.320783] pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[    0.320824] pci 0000:02:00.0: reg 0x10: [mem 0xf1d00000-0xf1d000ff]
[    0.321106] pci 0000:02:00.0: supports D1 D2
[    0.321108] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.321549] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.321556] pci 0000:00:1c.0:   bridge window [io  0x5000-0x5fff]
[    0.321563] pci 0000:00:1c.0:   bridge window [mem 0xf1d00000-0xf24fffff]
[    0.321573] pci 0000:00:1c.0:   bridge window [mem 0xf0400000-0xf0bfffff 64bit pref]
[    0.321919] pci 0000:03:00.0: [8086:0085] type 00 class 0x028000
[    0.322416] pci 0000:03:00.0: reg 0x10: [mem 0xf1c00000-0xf1c01fff 64bit]
[    0.324096] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    0.324876] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.324889] pci 0000:00:1c.1:   bridge window [mem 0xf1c00000-0xf1cfffff]
[    0.325045] acpiphp: Slot [1] registered
[    0.325058] pci 0000:00:1c.2: PCI bridge to [bus 04-0b]
[    0.325064] pci 0000:00:1c.2:   bridge window [io  0x4000-0x4fff]
[    0.325070] pci 0000:00:1c.2:   bridge window [mem 0xf1400000-0xf1bfffff]
[    0.325080] pci 0000:00:1c.2:   bridge window [mem 0xf0c00000-0xf13fffff 64bit pref]
[    0.327463] ACPI: EC: interrupt unblocked
[    0.327481] ACPI: EC: event unblocked
[    0.327490] ACPI: \_SB_.PCI0.LPC_.EC__: GPE=0x11, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[    0.327493] ACPI: \_SB_.PCI0.LPC_.EC__: Boot DSDT EC used to handle transactions and events
[    0.327630] SCSI subsystem initialized
[    0.327630] libata version 3.00 loaded.
[    0.327630] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.327630] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.327630] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.327630] vgaarb: loaded
[    0.327630] ACPI: bus type USB registered
[    0.327630] usbcore: registered new interface driver usbfs
[    0.327630] usbcore: registered new interface driver hub
[    0.328244] usbcore: registered new device driver usb
[    0.328244] pps_core: LinuxPPS API ver. 1 registered
[    0.328244] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.328244] PTP clock support registered
[    0.328268] EDAC MC: Ver: 3.0.0
[    0.328485] Registered efivars operations
[    0.328485] PCI: Using ACPI for IRQ routing
[    0.328710] PCI: pci_cache_line_size set to 64 bytes
[    0.329200] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
[    0.329202] e820: reserve RAM buffer [mem 0xd0fcf000-0xd3ffffff]
[    0.329204] e820: reserve RAM buffer [mem 0xd1c2b018-0xd3ffffff]
[    0.329206] e820: reserve RAM buffer [mem 0xd1c3c018-0xd3ffffff]
[    0.329207] e820: reserve RAM buffer [mem 0xd684f000-0xd7ffffff]
[    0.329209] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
[    0.329211] e820: reserve RAM buffer [mem 0x21e600000-0x21fffffff]
[    0.329426] NetLabel: Initializing
[    0.329428] NetLabel:  domain hash size = 128
[    0.329429] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.329458] NetLabel:  unlabeled traffic allowed by default
[    0.333514] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.333522] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.336280] clocksource: Switched to clocksource tsc-early
[    0.361046] VFS: Disk quotas dquot_6.6.0
[    0.361078] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.361132] *** VALIDATE hugetlbfs ***
[    0.361284] AppArmor: AppArmor Filesystem Enabled
[    0.361341] pnp: PnP ACPI init
[    0.362730] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.362734] system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
[    0.362736] system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
[    0.362739] system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved
[    0.362741] system 00:00: [mem 0x000cc000-0x000cffff] has been reserved
[    0.362744] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[    0.362746] system 00:00: [mem 0x000d4000-0x000d7fff] has been reserved
[    0.362749] system 00:00: [mem 0x000d8000-0x000dbfff] has been reserved
[    0.362751] system 00:00: [mem 0x000dc000-0x000dffff] has been reserved
[    0.362754] system 00:00: [mem 0x000e0000-0x000e3fff] has been reserved
[    0.362756] system 00:00: [mem 0x000e4000-0x000e7fff] has been reserved
[    0.362759] system 00:00: [mem 0x000e8000-0x000ebfff] has been reserved
[    0.362761] system 00:00: [mem 0x000ec000-0x000effff] has been reserved
[    0.362764] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[    0.362766] system 00:00: [mem 0x00100000-0xdf9fffff] could not be reserved
[    0.362769] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
[    0.362772] system 00:00: [mem 0xfed4c000-0xffffffff] has been reserved
[    0.362782] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.363007] pnp 00:01: [Firmware Bug]: PNP resource [mem 0xfed10000-0xfed13fff] covers only part of 0000:00:00.0 Intel MCH; extending to [mem 0xfed10000-0xfed17fff]
[    0.363043] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.363046] system 00:01: [io  0x0500-0x057f] has been reserved
[    0.363049] system 00:01: [io  0x0800-0x080f] has been reserved
[    0.363051] system 00:01: [io  0x15e0-0x15ef] has been reserved
[    0.363054] system 00:01: [io  0x1600-0x167f] has been reserved
[    0.363058] system 00:01: [mem 0xf8000000-0xfbffffff] could not be reserved
[    0.363061] system 00:01: [mem 0xfffff000-0xffffffff] has been reserved
[    0.363064] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.363066] system 00:01: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.363069] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.363072] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.363074] system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
[    0.363082] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.363199] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.363246] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.363286] pnp 00:04: Plug and Play ACPI device, IDs LEN0020 PNP0f13 (active)
[    0.363401] pnp 00:05: Plug and Play ACPI device, IDs SMO1200 PNP0c31 (active)
[    0.364671] pnp: PnP ACPI: found 6 devices
[    0.367274] thermal_sys: Registered thermal governor 'fair_share'
[    0.367275] thermal_sys: Registered thermal governor 'bang_bang'
[    0.367277] thermal_sys: Registered thermal governor 'step_wise'
[    0.367278] thermal_sys: Registered thermal governor 'user_space'
[    0.367280] thermal_sys: Registered thermal governor 'power_allocator'
[    0.371813] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.371890] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.371899] pci 0000:00:1c.0:   bridge window [io  0x5000-0x5fff]
[    0.371909] pci 0000:00:1c.0:   bridge window [mem 0xf1d00000-0xf24fffff]
[    0.371915] pci 0000:00:1c.0:   bridge window [mem 0xf0400000-0xf0bfffff 64bit pref]
[    0.371926] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.371935] pci 0000:00:1c.1:   bridge window [mem 0xf1c00000-0xf1cfffff]
[    0.371950] pci 0000:00:1c.2: PCI bridge to [bus 04-0b]
[    0.371955] pci 0000:00:1c.2:   bridge window [io  0x4000-0x4fff]
[    0.371963] pci 0000:00:1c.2:   bridge window [mem 0xf1400000-0xf1bfffff]
[    0.371969] pci 0000:00:1c.2:   bridge window [mem 0xf0c00000-0xf13fffff 64bit pref]
[    0.371981] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.371984] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.371986] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.371989] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfebfffff window]
[    0.371991] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed4bfff window]
[    0.371993] pci_bus 0000:02: resource 0 [io  0x5000-0x5fff]
[    0.371995] pci_bus 0000:02: resource 1 [mem 0xf1d00000-0xf24fffff]
[    0.371998] pci_bus 0000:02: resource 2 [mem 0xf0400000-0xf0bfffff 64bit pref]
[    0.372000] pci_bus 0000:03: resource 1 [mem 0xf1c00000-0xf1cfffff]
[    0.372002] pci_bus 0000:04: resource 0 [io  0x4000-0x4fff]
[    0.372004] pci_bus 0000:04: resource 1 [mem 0xf1400000-0xf1bfffff]
[    0.372006] pci_bus 0000:04: resource 2 [mem 0xf0c00000-0xf13fffff 64bit pref]
[    0.372233] NET: Registered protocol family 2
[    0.372503] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.372587] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.372896] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    0.373069] TCP: Hash tables configured (established 65536 bind 65536)
[    0.373149] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.373198] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.373376] NET: Registered protocol family 1
[    0.373385] NET: Registered protocol family 44
[    0.373404] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.374516] PCI: CLS 64 bytes, default 64
[    0.374600] Trying to unpack rootfs image as initramfs...
[    0.610581] Initramfs unpacking failed: Decoding failed
[    0.619992] Freeing initrd memory: 46764K
[    0.620032] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.620035] software IO TLB: mapped [mem 0xcac30000-0xcec30000] (64MB)
[    0.620434] check: Scanning for low memory corruption every 60 seconds
[    0.624360] Initialise system trusted keyrings
[    0.624376] Key type blacklist registered
[    0.624432] workingset: timestamp_bits=36 max_order=21 bucket_order=0
[    0.627259] zbud: loaded
[    0.628005] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.628311] fuse: init (API version 7.31)
[    0.628519] Platform Keyring initialized
[    0.639971] Key type asymmetric registered
[    0.639974] Asymmetric key parser 'x509' registered
[    0.639996] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.640082] io scheduler mq-deadline registered
[    0.641394] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.641515] efifb: probing for efifb
[    0.641538] efifb: No BGRT, not showing boot graphics
[    0.641541] efifb: framebuffer at 0xe0000000, using 1200k, total 1200k
[    0.641543] efifb: mode is 640x480x32, linelength=2560, pages=1
[    0.641543] efifb: scrolling: redraw
[    0.641546] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.641638] fbcon: Deferring console take-over
[    0.641641] fb0: EFI VGA frame buffer device
[    0.641657] intel_idle: MWAIT substates: 0x21120
[    0.641658] intel_idle: v0.4.1 model 0x3A
[    0.642014] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.642462] ACPI: AC Adapter [AC] (off-line)
[    0.642568] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.642592] ACPI: Lid Switch [LID]
[    0.642652] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    0.642668] ACPI: Sleep Button [SLPB]
[    0.642756] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.642771] ACPI: Power Button [PWRF]
[    0.646186] thermal LNXTHERM:00: registered as thermal_zone0
[    0.646189] ACPI: Thermal Zone [THM0] (34 C)
[    0.646603] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.657556] Linux agpgart interface v0.103
[    0.664313] tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
[    0.665413] battery: ACPI: Battery Slot [BAT0] (battery present)
[    0.753264] loop: module loaded
[    0.753711] libphy: Fixed MDIO Bus: probed
[    0.753713] tun: Universal TUN/TAP device driver, 1.6
[    0.753817] PPP generic driver version 2.4.2
[    0.753951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.753956] ehci-pci: EHCI PCI platform driver
[    0.754210] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    0.754220] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    0.754244] ehci-pci 0000:00:1a.0: debug port 2
[    0.758158] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    0.758181] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf253a000
[    0.772322] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    0.772439] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
[    0.772442] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.772444] usb usb1: Product: EHCI Host Controller
[    0.772447] usb usb1: Manufacturer: Linux 5.3.0-46-generic ehci_hcd
[    0.772449] usb usb1: SerialNumber: 0000:00:1a.0
[    0.772841] hub 1-0:1.0: USB hub found
[    0.772859] hub 1-0:1.0: 3 ports detected
[    0.773544] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    0.773557] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.773582] ehci-pci 0000:00:1d.0: debug port 2
[    0.777506] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    0.777535] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf2539000
[    0.792325] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.792480] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
[    0.792484] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.792486] usb usb2: Product: EHCI Host Controller
[    0.792489] usb usb2: Manufacturer: Linux 5.3.0-46-generic ehci_hcd
[    0.792490] usb usb2: SerialNumber: 0000:00:1d.0
[    0.792874] hub 2-0:1.0: USB hub found
[    0.792892] hub 2-0:1.0: 3 ports detected
[    0.793340] ehci-platform: EHCI generic platform driver
[    0.793376] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.793389] ohci-pci: OHCI PCI platform driver
[    0.793415] ohci-platform: OHCI generic platform driver
[    0.793434] uhci_hcd: USB Universal Host Controller Interface driver
[    0.793726] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.793738] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[    0.794846] xhci_hcd 0000:00:14.0: hcc params 0x20007181 hci version 0x100 quirks 0x000000000000b930
[    0.794859] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    0.795154] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
[    0.795157] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.795159] usb usb3: Product: xHCI Host Controller
[    0.795161] usb usb3: Manufacturer: Linux 5.3.0-46-generic xhci-hcd
[    0.795163] usb usb3: SerialNumber: 0000:00:14.0
[    0.795488] hub 3-0:1.0: USB hub found
[    0.795508] hub 3-0:1.0: 4 ports detected
[    0.796624] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.796631] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[    0.796637] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    0.796710] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.03
[    0.796713] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.796715] usb usb4: Product: xHCI Host Controller
[    0.796717] usb usb4: Manufacturer: Linux 5.3.0-46-generic xhci-hcd
[    0.796719] usb usb4: SerialNumber: 0000:00:14.0
[    0.797005] hub 4-0:1.0: USB hub found
[    0.797025] hub 4-0:1.0: 4 ports detected
[    0.798321] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[    0.800400] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.800409] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.800782] mousedev: PS/2 mouse device common for all mice
[    0.801317] rtc_cmos 00:02: RTC can wake from S4
[    0.801554] rtc_cmos 00:02: registered as rtc0
[    0.801583] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.801595] i2c /dev entries driver
[    0.801692] device-mapper: uevent: version 1.0.3
[    0.801828] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    0.801866] platform eisa.0: Probing EISA bus 0
[    0.801869] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    0.801872] platform eisa.0: Cannot allocate resource for EISA slot 1
[    0.801874] platform eisa.0: Cannot allocate resource for EISA slot 2
[    0.801876] platform eisa.0: Cannot allocate resource for EISA slot 3
[    0.801878] platform eisa.0: Cannot allocate resource for EISA slot 4
[    0.801880] platform eisa.0: Cannot allocate resource for EISA slot 5
[    0.801882] platform eisa.0: Cannot allocate resource for EISA slot 6
[    0.801884] platform eisa.0: Cannot allocate resource for EISA slot 7
[    0.801886] platform eisa.0: Cannot allocate resource for EISA slot 8
[    0.801888] platform eisa.0: EISA: Detected 0 cards
[    0.801897] intel_pstate: Intel P-state driver initializing
[    0.802194] ledtrig-cpu: registered to indicate activity on CPUs
[    0.802198] EFI Variables Facility v0.08 2004-May-17
[    0.802458] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    0.820357] NET: Registered protocol family 10
[    0.827702] Segment Routing with IPv6
[    0.827726] NET: Registered protocol family 17
[    0.827761] Key type dns_resolver registered
[    0.827966] RAS: Correctable Errors collector initialized.
[    0.827999] microcode: sig=0x306a9, pf=0x10, revision=0x21
[    0.828031] microcode: Microcode Update Driver: v2.2.
[    0.828046] sched_clock: Marking stable (827486045, 541883)->(873467104, -45439176)
[    0.828152] registered taskstats version 1
[    0.828159] Loading compiled-in X.509 certificates
[    0.830157] Loaded X.509 cert 'Build time autogenerated kernel key: 58cc9974d2170f3c76d2e16eeb21349faa3b1809'
[    0.830188] zswap: loaded using pool lzo/zbud
[    0.837190] Key type big_key registered
[    0.837199] Key type trusted registered
[    0.840626] Key type encrypted registered
[    0.840629] AppArmor: AppArmor sha1 policy hashing enabled
[    0.841082] integrity: Loading X.509 certificate: UEFI:db
[    0.841113] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53'
[    0.841113] integrity: Loading X.509 certificate: UEFI:db
[    0.841132] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4'
[    0.841132] integrity: Loading X.509 certificate: UEFI:db
[    0.841146] integrity: Loaded X.509 cert 'Lenovo Ltd.: ThinkPad Product CA 2012: 838b1f54c1550463f45f98700640f11069265949'
[    0.841675] ima: Allocated hash algorithm: sha1
[    0.988414] No architecture policies found
[    0.988439] evm: Initialising EVM extended attributes:
[    0.988440] evm: security.selinux
[    0.988440] evm: security.SMACK64
[    0.988441] evm: security.SMACK64EXEC
[    0.988441] evm: security.SMACK64TRANSMUTE
[    0.988441] evm: security.SMACK64MMAP
[    0.988442] evm: security.apparmor
[    0.988442] evm: security.ima
[    0.988442] evm: security.capability
[    0.988443] evm: HMAC attrs: 0x1
[    0.988775] PM:   Magic number: 0:131:237
[    0.988907] rtc_cmos 00:02: setting system clock to 2020-04-17T16:12:07 UTC (1587139927)
[    0.990187] Freeing unused decrypted memory: 2040K
[    0.990575] Freeing unused kernel image memory: 2676K
[    0.990626] Write protecting the kernel read-only data: 22528k
[    0.991018] Freeing unused kernel image memory: 2008K
[    0.991223] Freeing unused kernel image memory: 1420K
[    1.000250] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.000251] x86/mm: Checking user space page tables
[    1.008922] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.008928] Run /init as init process
[    1.093884] acpi PNP0C14:01: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
[    1.094003] acpi PNP0C14:02: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
[    1.097573] sdhci: Secure Digital Host Controller Interface driver
[    1.097574] sdhci: Copyright(c) Pierre Ossman
[    1.097989] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\_SB.PCI0.LPC.PMIO) (20190703/utaddress-204)
[    1.098000] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    1.098049] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    1.098057] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPC.LPIO) (20190703/utaddress-204)
[    1.098064] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    1.098149] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPC.LPIO) (20190703/utaddress-204)
[    1.098156] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    1.098168] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPC.LPIO) (20190703/utaddress-204)
[    1.098174] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    1.098174] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    1.108253] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.118916] sdhci-pci 0000:02:00.0: SDHCI controller found [1180:e823] (rev 4)
[    1.119094] ahci 0000:00:1f.2: version 3.0
[    1.119893] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.119894] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.120722] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
[    1.120779] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    1.121052] mmc0: SDHCI controller on PCI [0000:02:00.0] using DMA
[    1.122155] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    1.128253] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.132267] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x13 impl SATA mode
[    1.132270] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst 
[    1.137173] usb 1-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[    1.137175] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.137466] hub 1-1:1.0: USB hub found
[    1.137675] hub 1-1:1.0: 6 ports detected
[    1.156759] usb 2-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[    1.156761] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.157029] hub 2-1:1.0: USB hub found
[    1.157034] scsi host0: ahci
[    1.157119] hub 2-1:1.0: 8 ports detected
[    1.157162] scsi host1: ahci
[    1.157295] scsi host2: ahci
[    1.157437] scsi host3: ahci
[    1.157517] scsi host4: ahci
[    1.158204] scsi host5: ahci
[    1.158243] ata1: SATA max UDMA/133 abar m2048@0xf2538000 port 0xf2538100 irq 29
[    1.158245] ata2: SATA max UDMA/133 abar m2048@0xf2538000 port 0xf2538180 irq 29
[    1.158246] ata3: DUMMY
[    1.158246] ata4: DUMMY
[    1.158248] ata5: SATA max UDMA/133 abar m2048@0xf2538000 port 0xf2538300 irq 29
[    1.158257] ata6: DUMMY
[    1.246138] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
[    1.345965] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 3c:97:0e:62:a8:9d
[    1.345969] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[    1.346035] e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: 1000FF-0FF
[    1.347145] e1000e 0000:00:19.0 enp0s25: renamed from eth0
[    1.424331] usb 1-1.4: new full-speed USB device number 3 using ehci-pci
[    1.475655] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.480515] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[    1.480520] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[    1.489524] ata1.00: ATA-9: Solid, S1022A0, max UDMA/133
[    1.489528] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 32), AA
[    1.498509] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[    1.498514] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[    1.507522] ata1.00: configured for UDMA/133
[    1.517918] scsi 0:0:0:0: Direct-Access     ATA      Solid            2A0  PQ: 0 ANSI: 5
[    1.518391] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.518538] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[    1.518573] sd 0:0:0:0: [sda] Write Protect is off
[    1.518575] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.518603] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.519996]  sda: sda1 sda2
[    1.520333] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.537385] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=21e6, bcdDevice= 1.12
[    1.537387] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.537388] usb 1-1.4: Product: BCM20702A0
[    1.537389] usb 1-1.4: Manufacturer: Broadcom Corp
[    1.537390] usb 1-1.4: SerialNumber: 7CE9D3E518F6
[    1.616319] usb 1-1.6: new high-speed USB device number 4 using ehci-pci
[    1.653697] usb 1-1.6: New USB device found, idVendor=04f2, idProduct=b2ea, bcdDevice= 5.18
[    1.653699] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.653700] usb 1-1.6: Product: Integrated Camera
[    1.653701] usb 1-1.6: Manufacturer: Chicony Electronics Co., Ltd.
[    1.656253] tsc: Refined TSC clocksource calibration: 2494.334 MHz
[    1.656262] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x23f45126d86, max_idle_ns: 440795256522 ns
[    1.656276] clocksource: Switched to clocksource tsc
[    1.831540] ata2: SATA link down (SStatus 0 SControl 300)
[    1.877477] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[    1.908595] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[    1.969529] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd002a3/0x940300/0x123800/0x0, board id: 1611, fw id: 1099905
[    1.969544] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
[    2.008389] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[    2.147607] ata5: SATA link down (SStatus 0 SControl 300)
[    2.227831] fbcon: Taking over console
[    2.227897] Console: switching to colour frame buffer device 80x30
[    2.233887] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    2.384568] systemd[1]: Inserted module 'autofs4'
[    2.435552] systemd[1]: systemd 242 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    2.452467] systemd[1]: Detected architecture x86-64.
[    2.454346] systemd[1]: Set hostname to <michals-thinkpad>.
[    2.455300] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
[    2.554379] systemd[1]: /lib/systemd/system/dbus.socket:4: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
[    2.618775] systemd[1]: Created slice User and Session Slice.
[    2.619119] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    2.619227] systemd[1]: Listening on Journal Socket (/dev/log).
[    2.619238] systemd[1]: Reached target Remote File Systems.
[    2.619315] systemd[1]: Listening on udev Kernel Socket.
[    2.646366] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
[    2.647076] lp: driver loaded but no devices found
[    2.652888] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[    2.658466] ppdev: user-space parallel port driver
[    2.784253] Adding 2097148k swap on /swapfile.  Priority:-2 extents:6 across:2260988k SSFS
[    2.851860] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input6
[    3.046796] systemd-journald[324]: Received request to flush runtime journal from PID 1
[    3.261783] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[    3.261785] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[    3.261786] RAPL PMU: hw unit of domain package 2^-16 Joules
[    3.261786] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[    3.261895] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.268846] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.282540] cryptd: max_cpu_qlen set to 1000
[    3.295282] mc: Linux media interface: v0.10
[    3.308206] AVX version of gcm_enc/dec engaged.
[    3.308207] AES CTR mode by8 optimization enabled
[    3.342786] Intel(R) Wireless WiFi driver for Linux
[    3.342787] Copyright(c) 2003- 2015 Intel Corporation
[    3.343113] iwlwifi 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[    3.344730] videodev: Linux video capture interface: v2.00
[    3.373538] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
[    3.445862] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled
[    3.445865] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled
[    3.445866] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[    3.445868] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
[    3.461895] uvcvideo: Found UVC 1.00 device Integrated Camera (04f2:b2ea)
[    3.470841] uvcvideo 1-1.6:1.0: Entity type for entity Extension 4 was not initialized!
[    3.470844] uvcvideo 1-1.6:1.0: Entity type for entity Extension 3 was not initialized!
[    3.470846] uvcvideo 1-1.6:1.0: Entity type for entity Processing 2 was not initialized!
[    3.470847] uvcvideo 1-1.6:1.0: Entity type for entity Camera 1 was not initialized!
[    3.470930] input: Integrated Camera: Integrated C as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input7
[    3.471160] usbcore: registered new interface driver uvcvideo
[    3.471161] USB Video Class driver (1.1.1)
[    3.484529] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[    3.543983] Bluetooth: Core ver 2.22
[    3.544002] NET: Registered protocol family 31
[    3.544003] Bluetooth: HCI device and connection manager initialized
[    3.544006] Bluetooth: HCI socket layer initialized
[    3.544008] Bluetooth: L2CAP socket layer initialized
[    3.544012] Bluetooth: SCO socket layer initialized
[    3.571225] usbcore: registered new interface driver btusb
[    3.582701] checking generic (e0000000 12c000) vs hw (e0000000 10000000)
[    3.582704] fb0: switching to inteldrmfb from EFI VGA
[    3.607611] Console: switching to colour dummy device 80x25
[    3.607670] i915 0000:00:02.0: vgaarb: deactivate vga console
[    3.610054] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.610056] [drm] Driver supports precise vblank timestamp query.
[    3.616929] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    3.626109] Non-volatile memory driver v1.3
[    3.655284] thinkpad_acpi: ThinkPad ACPI Extras v0.26
[    3.655285] thinkpad_acpi: http://ibm-acpi.sf.net/
[    3.655286] thinkpad_acpi: ThinkPad BIOS G2ETB4WW (2.74 ), EC G2HT35WW
[    3.655287] thinkpad_acpi: Lenovo ThinkPad X230, model 2325J67
[    3.660060] thinkpad_acpi: radio switch found; radios are enabled
[    3.660184] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[    3.660185] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[    3.668409] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[    3.674583] kvm: disabled by bios
[    3.679607] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[    3.686709] Bluetooth: hci0: BCM: chip id 63
[    3.687575] Bluetooth: hci0: BCM: features 0x07
[    3.703992] Bluetooth: hci0: BCM20702A
[    3.705696] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[    3.709570] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[    3.709575] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[    3.710385] kvm: disabled by bios
[    3.717488] thinkpad_acpi: battery 1 registered (start 0, stop 100)
[    3.717494] battery: new extension: ThinkPad Battery Extension
[    3.717652] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input8
[    3.725018] [drm] Initialized i915 1.6.0 20190619 for 0000:00:02.0 on minor 0
[    3.726158] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[    3.729986] acpi device:00: registered as cooling_device4
[    3.730123] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input9
[    3.751235] kvm: disabled by bios
[    3.787648] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[    3.810793] kvm: disabled by bios
[    3.824272] intel_rapl_common: Found RAPL domain package
[    3.824273] intel_rapl_common: Found RAPL domain core
[    3.824275] intel_rapl_common: Found RAPL domain uncore
[    3.824280] intel_rapl_common: RAPL package-0 domain package locked by BIOS
[    3.939033] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[    3.939573] fbcon: i915drmfb (fb0) is primary device
[    3.939681] Console: switching to colour frame buffer device 170x48
[    3.939708] i915 0000:00:02.0: fb0: i915drmfb frame buffer device
[    3.957564] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269VC: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[    3.957566] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    3.957567] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=2 (0x15/0x1b/0x0/0x0/0x0)
[    3.957568] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    3.957568] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    3.957570] snd_hda_codec_realtek hdaudioC0D0:      Mic=0x18
[    3.957571] snd_hda_codec_realtek hdaudioC0D0:      Dock Mic=0x19
[    3.957572] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x12
[    3.982089] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[    3.982180] input: HDA Intel PCH Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    3.982253] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    3.982351] input: HDA Intel PCH Dock Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[    3.982421] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[    3.982490] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[    3.982557] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[    4.505913] audit: type=1400 audit(1587139931.011:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=750 comm="apparmor_parser"
[    4.507193] audit: type=1400 audit(1587139931.011:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=753 comm="apparmor_parser"
[    4.513006] audit: type=1400 audit(1587139931.019:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=755 comm="apparmor_parser"
[    4.513012] audit: type=1400 audit(1587139931.019:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=755 comm="apparmor_parser"
[    4.522579] kvm: disabled by bios
[    4.532645] audit: type=1400 audit(1587139931.039:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=757 comm="apparmor_parser"
[    4.541373] audit: type=1400 audit(1587139931.047:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/tcpdump" pid=760 comm="apparmor_parser"
[    4.541785] audit: type=1400 audit(1587139931.047:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=756 comm="apparmor_parser"
[    4.541789] audit: type=1400 audit(1587139931.047:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=756 comm="apparmor_parser"
[    4.541791] audit: type=1400 audit(1587139931.047:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd//third_party" pid=756 comm="apparmor_parser"
[    7.995923] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    7.995924] Bluetooth: BNEP filters: protocol multicast
[    7.995928] Bluetooth: BNEP socket layer initialized
[    8.861696] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[    9.160424] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[   11.772748] rfkill: input handler disabled
[   12.698778] wlp3s0: authenticate with 4c:1b:86:67:2e:b8
[   12.702144] wlp3s0: send auth to 4c:1b:86:67:2e:b8 (try 1/3)
[   12.706087] wlp3s0: authenticated
[   12.708280] wlp3s0: associate with 4c:1b:86:67:2e:b8 (try 1/3)
[   12.709313] wlp3s0: RX AssocResp from 4c:1b:86:67:2e:b8 (capab=0x11 status=0 aid=3)
[   12.711771] wlp3s0: associated
[   12.749941] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[   12.807301] wlp3s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 4c:1b:86:67:2e:b8
[   24.809751] kauditd_printk_skb: 33 callbacks suppressed
[   24.809753] audit: type=1400 audit(1587139951.315:44): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.gnome-calculator.gnome-calculator" pid=1460 comm="apparmor_parser"
[   24.843526] audit: type=1400 audit(1587139951.347:45): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap-update-ns.gnome-characters" pid=1461 comm="apparmor_parser"
[   25.028394] audit: type=1400 audit(1587139951.535:46): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.gnome-characters.gnome-characters" pid=1462 comm="apparmor_parser"
[   25.337966] audit: type=1400 audit(1587139951.843:47): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap-update-ns.gnome-calculator" pid=1459 comm="apparmor_parser"
[   25.358681] audit: type=1400 audit(1587139951.863:48): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap-update-ns.gnome-logs" pid=1463 comm="apparmor_parser"
[   25.446683] audit: type=1400 audit(1587139951.951:49): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.gnome-logs.gnome-logs" pid=1464 comm="apparmor_parser"
[   29.825142] Bluetooth: RFCOMM TTY layer initialized
[   29.825161] Bluetooth: RFCOMM socket layer initialized
[   29.825178] Bluetooth: RFCOMM ver 1.11
[   29.864347] rfkill: input handler enabled
[   33.906296] rfkill: input handler disabled
[  742.319102] audit: type=1400 audit(1587140668.015:50): apparmor="DENIED" operation="capable" profile="/snap/core/8935/usr/lib/snapd/snap-confine" pid=4023 comm="snap-confine" capability=4  capname="fsetid"
[  745.931421] audit: type=1107 audit(1587140671.627:51): pid=800 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call"  bus="system" path="/" interface="org.freedesktop.DBus.ObjectManager" member="GetManagedObjects" mask="send" name="org.bluez" pid=4023 label="snap.whatsdesk.whatsdesk" peer_pid=813 peer_label="unconfined"
                exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[  784.596828] atkbd serio0: Unknown key pressed (translated set 2, code 0xd8 on isa0060/serio0).
[  784.596833] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[  784.597126] atkbd serio0: Unknown key released (translated set 2, code 0xd8 on isa0060/serio0).
[  784.597130] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[  789.032294] PM: suspend entry (deep)
[  789.076388] Filesystems sync: 0.044 seconds
[  789.076967] Freezing user space processes ... (elapsed 0.003 seconds) done.
[  789.080797] OOM killer disabled.
[  789.080798] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[  789.082278] printk: Suspending console(s) (use no_console_suspend to debug)
[  789.116285] wlp3s0: deauthenticating from 4c:1b:86:67:2e:b8 by local choice (Reason: 3=DEAUTH_LEAVING)
[  789.256034] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  789.256147] sd 0:0:0:0: [sda] Stopping disk
[  789.454323] e1000e: EEE TX LPI TIMER: 00000011
[  789.540888] ACPI: EC: interrupt blocked
[  789.580322] ACPI: Preparing to enter system sleep state S3
[  789.584856] ACPI: EC: event blocked
[  789.584857] ACPI: EC: EC stopped
[  789.584858] PM: Saving platform NVS memory
[  789.584878] Disabling non-boot CPUs ...
[  789.585412] IRQ 31: no longer affine to CPU1
[  789.586916] smpboot: CPU 1 is now offline
[  789.591543] IRQ 32: no longer affine to CPU2
[  789.593027] smpboot: CPU 2 is now offline
[  789.597108] IRQ 23: no longer affine to CPU3
[  789.598113] smpboot: CPU 3 is now offline
[  789.601375] ACPI: Low-level resume complete
[  789.601447] ACPI: EC: EC started
[  789.601448] PM: Restoring platform NVS memory
[  789.603621] Enabling non-boot CPUs ...
[  789.603714] x86: Booting SMP configuration:
[  789.603716] smpboot: Booting Node 0 Processor 1 APIC 0x1
[  789.607275] CPU1 is up
[  789.607342] smpboot: Booting Node 0 Processor 2 APIC 0x2
[  789.611746] CPU2 is up
[  789.611808] smpboot: Booting Node 0 Processor 3 APIC 0x3
[  789.614947] CPU3 is up
[  789.617162] ACPI: Waking up from system sleep state S3
[  789.626099] ACPI: EC: interrupt unblocked
[  789.645617] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[  789.667568] ACPI: EC: event unblocked
[  789.677085] sd 0:0:0:0: [sda] Starting disk
[  789.687743] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[  789.912994] usb 1-1.4: reset full-speed USB device number 3 using ehci-pci
[  789.995367] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[  790.016028] ata5: SATA link down (SStatus 0 SControl 300)
[  790.016060] ata2: SATA link down (SStatus 0 SControl 300)
[  790.016092] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[  790.020960] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[  790.020966] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[  790.038951] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[  790.038957] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[  790.047867] ata1.00: configured for UDMA/133
[  790.101011] usb 1-1.6: reset high-speed USB device number 4 using ehci-pci
[  790.367040] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[  790.398175] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[  790.507616] OOM killer enabled.
[  790.507618] Restarting tasks ... 
[  790.507651] ACPI: \_SB_.PCI0.LPC_.EC__.BAT1: docking
[  790.508284] ACPI: \_SB_.PCI0.LPC_.EC__.BAT1: Unable to dock!
[  790.537528] done.
[  790.553396] video LNXVIDEO:00: Restoring backlight state
[  790.554117] PM: suspend exit
[  790.634904] Bluetooth: hci0: BCM: chip id 63
[  790.635943] Bluetooth: hci0: BCM: features 0x07
[  790.651791] Bluetooth: hci0: BCM20702A
[  790.652905] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[  790.652981] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[  790.652985] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[  790.756558] e1000e: enp0s25 NIC Link is Down
[  791.406405] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[  791.706343] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[  795.110499] wlp3s0: authenticate with 4c:1b:86:67:2e:b8
[  795.112572] wlp3s0: send auth to 4c:1b:86:67:2e:b8 (try 1/3)
[  795.134821] wlp3s0: authenticated
[  795.136987] wlp3s0: associate with 4c:1b:86:67:2e:b8 (try 1/3)
[  795.138155] wlp3s0: RX AssocResp from 4c:1b:86:67:2e:b8 (capab=0x11 status=0 aid=2)
[  795.141200] wlp3s0: associated
[  795.148839] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[  795.236537] wlp3s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 4c:1b:86:67:2e:b8
[ 3858.671437] perf: interrupt took too long (2508 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
[ 4840.106618] perf: interrupt took too long (3201 > 3135), lowering kernel.perf_event_max_sample_rate to 62250
[ 6005.815305] perf: interrupt took too long (4010 > 4001), lowering kernel.perf_event_max_sample_rate to 49750
[10016.435759] perf: interrupt took too long (5019 > 5012), lowering kernel.perf_event_max_sample_rate to 39750
[13661.587181] atkbd serio0: Unknown key pressed (translated set 2, code 0xd8 on isa0060/serio0).
[13661.587187] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[13661.587809] atkbd serio0: Unknown key released (translated set 2, code 0xd8 on isa0060/serio0).
[13661.587816] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[13661.656450] PM: suspend entry (deep)
[13661.660125] Filesystems sync: 0.003 seconds
[13661.660379] Freezing user space processes ... (elapsed 0.246 seconds) done.
[13661.907285] OOM killer disabled.
[13661.907286] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[13661.909011] printk: Suspending console(s) (use no_console_suspend to debug)
[13661.943479] wlp3s0: deauthenticating from 4c:1b:86:67:2e:b8 by local choice (Reason: 3=DEAUTH_LEAVING)
[13662.111083] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[13662.111162] sd 0:0:0:0: [sda] Stopping disk
[13662.312348] e1000e: EEE TX LPI TIMER: 00000011
[13662.399653] ACPI: EC: interrupt blocked
[13662.439404] ACPI: Preparing to enter system sleep state S3
[13662.443718] ACPI: EC: event blocked
[13662.443719] ACPI: EC: EC stopped
[13662.443720] PM: Saving platform NVS memory
[13662.443740] Disabling non-boot CPUs ...
[13662.445740] smpboot: CPU 1 is now offline
[13662.448903] IRQ 32: no longer affine to CPU2
[13662.449916] smpboot: CPU 2 is now offline
[13662.452899] IRQ 31: no longer affine to CPU3
[13662.453909] smpboot: CPU 3 is now offline
[13662.456860] ACPI: Low-level resume complete
[13662.456936] ACPI: EC: EC started
[13662.456937] PM: Restoring platform NVS memory
[13662.459122] Enabling non-boot CPUs ...
[13662.459216] x86: Booting SMP configuration:
[13662.459218] smpboot: Booting Node 0 Processor 1 APIC 0x1
[13662.462706] CPU1 is up
[13662.462771] smpboot: Booting Node 0 Processor 2 APIC 0x2
[13662.467144] CPU2 is up
[13662.467207] smpboot: Booting Node 0 Processor 3 APIC 0x3
[13662.470322] CPU3 is up
[13662.472473] ACPI: Waking up from system sleep state S3
[13662.482000] ACPI: EC: interrupt unblocked
[13662.504413] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[13662.523004] ACPI: EC: event unblocked
[13662.532662] sd 0:0:0:0: [sda] Starting disk
[13662.537816] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[13662.768134] usb 1-1.6: reset high-speed USB device number 4 using ehci-pci
[13662.837071] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[13662.871280] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[13662.871315] ata5: SATA link down (SStatus 0 SControl 300)
[13662.871348] ata2: SATA link down (SStatus 0 SControl 300)
[13662.876177] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[13662.876181] usb 1-1.4: reset full-speed USB device number 3 using ehci-pci
[13662.876186] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[13662.894009] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[13662.894014] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[13662.903124] ata1.00: configured for UDMA/133
[13663.226295] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[13663.257461] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[13663.365975] OOM killer enabled.
[13663.365977] Restarting tasks ... done.
[13663.414255] video LNXVIDEO:00: Restoring backlight state
[13663.414936] PM: suspend exit
[13663.502498] Bluetooth: hci0: BCM: chip id 63
[13663.503556] Bluetooth: hci0: BCM: features 0x07
[13663.519531] Bluetooth: hci0: BCM20702A
[13663.520592] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[13663.520618] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[13663.520621] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[13663.656707] e1000e: enp0s25 NIC Link is Down
[13664.320649] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[13664.616905] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[13667.984763] wlp3s0: authenticate with 4c:1b:86:67:2e:b7
[13667.995755] wlp3s0: send auth to 4c:1b:86:67:2e:b7 (try 1/3)
[13667.999856] wlp3s0: authenticated
[13668.000546] wlp3s0: associate with 4c:1b:86:67:2e:b7 (try 1/3)
[13668.004393] wlp3s0: RX AssocResp from 4c:1b:86:67:2e:b7 (capab=0x411 status=0 aid=3)
[13668.009237] wlp3s0: associated
[13668.020738] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[14173.191533] atkbd serio0: Unknown key pressed (translated set 2, code 0xd8 on isa0060/serio0).
[14173.191541] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[14173.191951] atkbd serio0: Unknown key released (translated set 2, code 0xd8 on isa0060/serio0).
[14173.191959] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[14177.507553] PM: suspend entry (deep)
[14177.511867] Filesystems sync: 0.004 seconds
[14177.512210] Freezing user space processes ... (elapsed 0.002 seconds) done.
[14177.514983] OOM killer disabled.
[14177.514984] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[14177.516342] printk: Suspending console(s) (use no_console_suspend to debug)
[14177.539873] wlp3s0: deauthenticating from 4c:1b:86:67:2e:b7 by local choice (Reason: 3=DEAUTH_LEAVING)
[14177.703633] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[14177.703701] sd 0:0:0:0: [sda] Stopping disk
[14177.900311] e1000e: EEE TX LPI TIMER: 00000011
[14177.988785] ACPI: EC: interrupt blocked
[14178.032309] ACPI: Preparing to enter system sleep state S3
[14178.036413] ACPI: EC: event blocked
[14178.036414] ACPI: EC: EC stopped
[14178.036415] PM: Saving platform NVS memory
[14178.036433] Disabling non-boot CPUs ...
[14178.038460] smpboot: CPU 1 is now offline
[14178.041570] IRQ 32: no longer affine to CPU2
[14178.043051] smpboot: CPU 2 is now offline
[14178.045998] IRQ 31: no longer affine to CPU3
[14178.047028] smpboot: CPU 3 is now offline
[14178.050590] ACPI: Low-level resume complete
[14178.050661] ACPI: EC: EC started
[14178.050662] PM: Restoring platform NVS memory
[14178.052980] Enabling non-boot CPUs ...
[14178.053075] x86: Booting SMP configuration:
[14178.053077] smpboot: Booting Node 0 Processor 1 APIC 0x1
[14178.056391] CPU1 is up
[14178.056461] smpboot: Booting Node 0 Processor 2 APIC 0x2
[14178.060872] CPU2 is up
[14178.060937] smpboot: Booting Node 0 Processor 3 APIC 0x3
[14178.064085] CPU3 is up
[14178.065481] ACPI: Waking up from system sleep state S3
[14178.075115] ACPI: EC: interrupt unblocked
[14178.093796] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[14178.117383] ACPI: EC: event unblocked
[14178.127777] sd 0:0:0:0: [sda] Starting disk
[14178.132080] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[14178.361524] usb 1-1.4: reset full-speed USB device number 3 using ehci-pci
[14178.442524] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[14178.468763] ata2: SATA link down (SStatus 0 SControl 300)
[14178.468802] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[14178.468836] ata5: SATA link down (SStatus 0 SControl 300)
[14178.473632] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[14178.473641] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[14178.491642] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[14178.491648] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[14178.500536] ata1.00: configured for UDMA/133
[14178.553687] usb 1-1.6: reset high-speed USB device number 4 using ehci-pci
[14178.826837] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[14178.858916] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[14178.968279] OOM killer enabled.
[14178.968281] Restarting tasks ... done.
[14179.001095] video LNXVIDEO:00: Restoring backlight state
[14179.001826] PM: suspend exit
[14179.120145] Bluetooth: hci0: BCM: chip id 63
[14179.121210] Bluetooth: hci0: BCM: features 0x07
[14179.137095] Bluetooth: hci0: BCM20702A
[14179.138174] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[14179.138204] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[14179.138208] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[14179.249339] e1000e: enp0s25 NIC Link is Down
[14179.836808] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[14179.917843] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
[14180.111843] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input17
[14180.133568] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[14183.485136] wlp3s0: authenticate with 4c:1b:86:67:2e:b8
[14183.487913] wlp3s0: send auth to 4c:1b:86:67:2e:b8 (try 1/3)
[14183.579913] wlp3s0: authenticated
[14183.581611] wlp3s0: associate with 4c:1b:86:67:2e:b8 (try 1/3)
[14183.582779] wlp3s0: RX AssocResp from 4c:1b:86:67:2e:b8 (capab=0x11 status=0 aid=2)
[14183.585850] wlp3s0: associated
[14183.594865] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[14183.681571] wlp3s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 4c:1b:86:67:2e:b8
[15532.502557] perf: interrupt took too long (6333 > 6273), lowering kernel.perf_event_max_sample_rate to 31500
[24225.741622] atkbd serio0: Unknown key pressed (translated set 2, code 0xd8 on isa0060/serio0).
[24225.741628] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[24225.742021] atkbd serio0: Unknown key released (translated set 2, code 0xd8 on isa0060/serio0).
[24225.742024] atkbd serio0: Use 'setkeycodes e058 <keycode>' to make it known.
[24230.419379] PM: suspend entry (deep)
[24230.425425] Filesystems sync: 0.006 seconds
[24230.425762] Freezing user space processes ... (elapsed 0.002 seconds) done.
[24230.428421] OOM killer disabled.
[24230.428422] Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
[24230.429408] printk: Suspending console(s) (use no_console_suspend to debug)
[24230.465808] wlp3s0: deauthenticating from 4c:1b:86:67:2e:b8 by local choice (Reason: 3=DEAUTH_LEAVING)
[24230.617412] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[24230.617495] sd 0:0:0:0: [sda] Stopping disk
[24230.811734] e1000e: EEE TX LPI TIMER: 00000011
[24230.898503] ACPI: EC: interrupt blocked
[24230.941714] ACPI: Preparing to enter system sleep state S3
[24230.946058] ACPI: EC: event blocked
[24230.946059] ACPI: EC: EC stopped
[24230.946060] PM: Saving platform NVS memory
[24230.946081] Disabling non-boot CPUs ...
[24230.948102] smpboot: CPU 1 is now offline
[24230.951259] IRQ 32: no longer affine to CPU2
[24230.952279] smpboot: CPU 2 is now offline
[24230.955190] IRQ 31: no longer affine to CPU3
[24230.956208] smpboot: CPU 3 is now offline
[24230.959538] ACPI: Low-level resume complete
[24230.959611] ACPI: EC: EC started
[24230.959613] PM: Restoring platform NVS memory
[24230.961925] Enabling non-boot CPUs ...
[24230.962019] x86: Booting SMP configuration:
[24230.962021] smpboot: Booting Node 0 Processor 1 APIC 0x1
[24230.965360] CPU1 is up
[24230.965429] smpboot: Booting Node 0 Processor 2 APIC 0x2
[24230.969822] CPU2 is up
[24230.969888] smpboot: Booting Node 0 Processor 3 APIC 0x3
[24230.973022] CPU3 is up
[24230.975256] ACPI: Waking up from system sleep state S3
[24230.984405] ACPI: EC: interrupt unblocked
[24231.002696] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[24231.024954] ACPI: EC: event unblocked
[24231.034740] sd 0:0:0:0: [sda] Starting disk
[24231.039954] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[24231.270408] usb 1-1.4: reset full-speed USB device number 3 using ehci-pci
[24231.343398] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[24231.373360] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[24231.373393] ata2: SATA link down (SStatus 0 SControl 300)
[24231.373427] ata5: SATA link down (SStatus 0 SControl 300)
[24231.378200] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[24231.378206] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[24231.396121] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[24231.396127] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[24231.405085] ata1.00: configured for UDMA/133
[24231.458392] usb 1-1.6: reset high-speed USB device number 4 using ehci-pci
[24231.735755] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[24231.766980] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[24231.875515] OOM killer enabled.
[24231.875516] Restarting tasks ... done.
[24231.918527] video LNXVIDEO:00: Restoring backlight state
[24231.919228] PM: suspend exit
[24232.014006] Bluetooth: hci0: BCM: chip id 63
[24232.014876] Bluetooth: hci0: BCM: features 0x07
[24232.030939] Bluetooth: hci0: BCM20702A
[24232.032000] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[24232.032020] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[24232.032022] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[24232.134864] e1000e: enp0s25 NIC Link is Down
[24232.787654] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[24233.087218] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[24236.392992] wlp3s0: authenticate with 4c:1b:86:67:2e:b8
[24236.395303] wlp3s0: send auth to 4c:1b:86:67:2e:b8 (try 1/3)
[24236.482494] wlp3s0: authenticated
[24236.490375] wlp3s0: associate with 4c:1b:86:67:2e:b8 (try 1/3)
[24236.491469] wlp3s0: RX AssocResp from 4c:1b:86:67:2e:b8 (capab=0x11 status=0 aid=3)
[24236.493918] wlp3s0: associated
[24236.500223] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[24236.584197] wlp3s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 4c:1b:86:67:2e:b8
[24244.826363] usb 3-1: new low-speed USB device number 2 using xhci_hcd
[24244.981741] usb 3-1: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00
[24244.981747] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[24244.981751] usb 3-1: Product: USB Optical Mouse
[24244.981755] usb 3-1: Manufacturer: Logitech
[24245.008890] hidraw: raw HID events driver (C) Jiri Kosina
[24245.013977] usbcore: registered new interface driver usbhid
[24245.013978] usbhid: USB HID core driver
[24245.029981] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.0/0003:046D:C077.0001/input/input18
[24245.030264] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-1/input0
[24252.198317] usb 3-2: new full-speed USB device number 3 using xhci_hcd
[24252.349205] usb 3-2: New USB device found, idVendor=046d, idProduct=c24d, bcdDevice=80.00
[24252.349208] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[24252.349209] usb 3-2: Product: Logitech G710 Keyboard
[24252.349211] usb 3-2: Manufacturer: Logitech
[24252.352291] input: Logitech Logitech G710 Keyboard as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.0/0003:046D:C24D.0002/input/input19
[24252.410758] hid-generic 0003:046D:C24D.0002: input,hidraw1: USB HID v1.11 Keyboard [Logitech Logitech G710 Keyboard] on usb-0000:00:14.0-2/input0
[24252.413292] input: Logitech Logitech G710 Keyboard as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:046D:C24D.0003/input/input20
[24252.470543] input: Logitech Logitech G710 Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:046D:C24D.0003/input/input21
[24252.470730] hid-generic 0003:046D:C24D.0003: input,hiddev0,hidraw2: USB HID v1.11 Keyboard [Logitech Logitech G710 Keyboard] on usb-0000:00:14.0-2/input1
albfan commented 4 years ago

intel is know to have bad support for P2P on linux

This is what is expected for a proper driver supporting P2P

    Supported interface modes:
         * IBSS
         * managed
         * AP
         * AP/VLAN
         * monitor
         * mesh point
         * P2P-client
         * P2P-GO
         * outside context of a BSS

It look for that here:

https://github.com/albfan/miraclecast/blob/master/res/miracle-utils.sh#L112

If you're sure your hardware support p2p you need to find a proper driver

ghost commented 4 years ago

Thanks @albfan, any places to point me to how could I check if p2p is supported in iwlwifi driver and for my card? I tried searching myself but I couldn't find anything conclusive