search

alexreinert / debmatic

debmatic is a project to install the Homematic OCCU on Debian based systems (Debian, Ubuntu, Raspbian, Armbian)
185 stars 33 forks source link

HM-MOD-RPI-PCB wird nicht mehr erkannt #84

Closed michipi85 closed 4 years ago

michipi85 commented 4 years ago

Hallo, ich habe das Problem dass sich meine hm-rpc Adapter in Iobroker sich nicht mehr verbunden haben. Hab dann einiges probiert, ohne Erfolg, dass ich nun alles neu aufgesetzt habe. Nun funktioniert es allerdings immer noch nicht, habe schon den Verdacht, dass das Funkmodul den Geist aufgegeben hat.

Hier mal ein paar Infos. debmatic version: 3.49.17-41 Kernel modules: Available Raw UART dev: Not available Rasp.Pi3 UART: Assigned to GPIO pins HMRF Hardware: unknown HMIP Hardware: unknown Board serial: unknown Radio MAC: unknown SGTIN: unknown

bei "sudo systemctl list-dependencies debmatic" ist alles grün, bis auf

unter systemctl status debmatic-multimacd kommt inactive `● debmatic-multimacd.service - debmatic multimacd Loaded: loaded (/lib/systemd/system/debmatic-multimacd.service; enabled; vendor preset: enabled) Active: inactive (dead) Condition: start condition failed at Mon 2020-01-27 21:04:04 CET; 6min ago

Jan 27 20:12:10 raspberrypi systemd[1]: Condition check resulted in debmatic multimacd being skipped. Jan 27 21:04:04 raspberrypi systemd[1]: Condition check resulted in debmatic multimacd being skipped.`

genauso bei systemctl status debmatic-rfd `● debmatic-rfd.service - debmatic rfd Loaded: loaded (/lib/systemd/system/debmatic-rfd.service; enabled; vendor preset: enabled) Active: inactive (dead) Condition: start condition failed at Mon 2020-01-27 21:04:05 CET; 9min ago

Jan 27 20:12:10 raspberrypi systemd[1]: Condition check resulted in debmatic rfd being skipped. Jan 27 21:04:05 raspberrypi systemd[1]: Condition check resulted in debmatic rfd being skipped.`

Kann es an mein Funkmodul liegen oder liegt es vielleicht doch noch wo anders? Kann ich das Funkmodul irgendwie prüfen?

alexreinert commented 4 years ago

Das Problem dürfte hier liegen: Raw UART dev: Not available Was kommt bei

sudo dpkg -s pivccu-modules-raspberrypi
cat /boot/config.txt
michipi85 commented 4 years ago

das war das Problem, nabe nun das pivccu modul, nach installiert und läuft auch nun. Anschließend noch debmatic neu gestartet und jetzt funktioniert wieder alles. Vielen Dank. :)

opu1000 commented 3 years ago

Hallo,ich habe das gleiche Problem. Hier der Output bei den obengenanten Kommandos: sudo dpkg -s pivccu-modules-raspberrypi Package: pivccu-modules-raspberrypi Status: install ok installed Priority: extra Section: kernel Maintainer: Alexander Reinert alex@areinert.de Architecture: all Version: 2.0-15 Depends: raspberrypi-kernel-headers | linux-headers-raspi, pivccu-modules-dkms, bc Pre-Depends: debconf (>= 0.5) | debconf-2.0 Description: Raspberry Pi kernel modules needed for Homematic This package contains the Raspberry Pi kernel needed for Homematic. Homepage: https://github.com/alexreinert/piVCCU

cat /boot/config.txt

For more options and information see

http://rpf.io/configtxt

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode

hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

overscan_left=16

overscan_right=16

overscan_top=16

overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus

overscan.

framebuffer_width=1280

framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

hdmi_group=1

hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

config_hdmi_boost=4

uncomment for composite PAL

sdtv_mode=2

uncomment to overclock the arm. 700 MHz is the default.

arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

dtparam=i2c_arm=on

dtparam=i2s=on

dtparam=spi=on

Uncomment this to enable infrared communication.

dtoverlay=gpio-ir,gpio_pin=17

dtoverlay=gpio-ir-tx,gpio_pin=18

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on

[pi4]

Enable DRM VC4 V3D driver on top of the dispmanx display stack

dtoverlay=vc4-fkms-v3d max_framebuffers=2

[all]

dtoverlay=vc4-fkms-v3d

gpu_mem=16

dtoverlay=pivccu-raspberrypi dtoverlay=pi3-disable-bt

Woran könnte es noch liegen?