search

alexreinert / piVCCU

piVCCU is a project to install the original Homematic CCU3 firmware inside a virtualized container (lxc) on ARM based single board computers.
Apache License 2.0
302 stars 64 forks source link

RSSI Liste leer #218

Closed chriss158 closed 4 years ago

chriss158 commented 4 years ago

Hallo,

die RSSI Liste in devconfig scheint nicht zu funktionieren. http://192.168.0.29/tools/devconfig.cgi?cmd=show_rssi&sid=@XXXXXXX@

Es steht nur die Überschrift "RSSI List" auf der Seite.

Raspberry Pi3B+ + RPI-RF-MOD + einem verbundenen Aktor HmIP-BWTH

Folgende frisch installierte Systeme habe ich bisher mit demselben Fehler probiert:

Logs vom System: 2019-09-26-raspbian-buster-lite + piVCCU3 (stable)

Schon mal vielen Dank für die Hilfe.

Gruß Christian

pivccu-info piVCCU version: 3.49.17-33 Kernel modules: Available Raw UART dev: Available Rasp.Pi3 UART: Assigned to GPIO pins HMRF Hardware: RPI-RF-MOD HMIP Hardware: RPI-RF-MOD Board serial: 58A9A727D5 Radio MAC: unknown SGTIN: 3014F711A0001F58A9A727D5 State: RUNNING PID: 1215 IP: 192.168.0.29 CPU use: 41.92 seconds BlkIO use: 328.00 KiB Memory use: 114.93 MiB KMem use: 5.18 MiB Link: vethpivccu TX bytes: 3.99 MiB RX bytes: 713.28 KiB Total bytes: 4.68 MiB

pivccu-attach cat /var/log/messages Dec 27 15:52:39 piVCCU syslog.info syslogd started: BusyBox v1.29.2 Dec 27 15:52:39 piVCCU user.notice kernel: klogd started: BusyBox v1.29.2 (2019-12-02 17:04:43 CET) Dec 27 15:52:41 piVCCU syslog.info syslogd exiting Dec 27 15:52:41 ccu3-webui syslog.info syslogd started: BusyBox v1.29.2 Dec 27 15:52:41 ccu3-webui user.notice kernel: klogd started: BusyBox v1.29.2 (2019-12-02 17:04:43 CET) Dec 27 15:52:41 ccu3-webui daemon.err udhcpc[169]: started, v1.29.2 Dec 27 15:52:41 ccu3-webui daemon.err udhcpc[169]: sending discover Dec 27 15:52:41 ccu3-webui daemon.err udhcpc[169]: sending select for 192.168.0.29 Dec 27 15:52:41 ccu3-webui daemon.err udhcpc[169]: lease of 192.168.0.29 obtained, lease time 864000 Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:42 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:43 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:43 ccu3-webui user.info firewall: iptables v1.6.2: host/network fc00::' not found Tryiptables -h' or 'iptables --help' for more information. Dec 27 15:52:43 ccu3-webui user.info firewall: configuration set Dec 27 15:52:43 ccu3-webui daemon.info ifplugd(eth0)[325]: ifplugd 0.28 initializing. Dec 27 15:52:43 ccu3-webui daemon.info ifplugd(eth0)[325]: Using interface eth0/CA:FC:06:84:7B:63 with driver (version: 1.0) Dec 27 15:52:43 ccu3-webui daemon.info ifplugd(eth0)[325]: Using detection mode: SIOCETHTOOL Dec 27 15:52:43 ccu3-webui daemon.info ifplugd(eth0)[325]: Initialization complete, link beat detected. Dec 27 15:52:43 ccu3-webui daemon.warn ifplugd(eth0)[325]: Could not open /dev/tty, cannot beep. Dec 27 15:52:43 ccu3-webui daemon.info ifplugd(eth0)[325]: Executing '/etc/ifplugd/ifplugd.action eth0 up'. Dec 27 15:52:43 ccu3-webui daemon.warn ifplugd(eth0)[325]: client: ifup: interface eth0 already configured Dec 27 15:52:43 ccu3-webui daemon.info ifplugd(eth0)[325]: Program executed successfully. Dec 27 15:52:54 ccu3-webui daemon.notice ntpdate[333]: step time server 217.144.138.234 offset -0.004281 sec Dec 27 15:52:54 ccu3-webui daemon.notice ntpd[334]: ntpd 4.2.8p12@1.3728-o Mon Dec 2 16:03:15 UTC 2019 (1): Starting Dec 27 15:52:54 ccu3-webui daemon.info ntpd[334]: Command line: /usr/sbin/ntpd -g 0.de.pool.ntp.org 1.de.pool.ntp.org 2.de.pool.ntp.org 3.de.pool.ntp.org Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: proto: precision = 0.989 usec (-20) Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: Listen and drop on 0 v6wildcard [::]:123 Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: Listen and drop on 1 v4wildcard 0.0.0.0:123 Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: Listen normally on 2 lo 127.0.0.1:123 Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: Listen normally on 3 eth0 192.168.0.29:123 Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: Listen normally on 4 lo [::1]:123 Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: Listening on routing socket on fd #21 for interface updates Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: kernel reports TIME_ERROR: 0x2041: Clock Unsynchronized Dec 27 15:52:55 ccu3-webui daemon.info ntpd[336]: kernel reports TIME_ERROR: 0x2041: Clock Unsynchronized Dec 27 15:52:55 ccu3-webui daemon.err xinetd[354]: Unable to read included directory: /etc/config/xinetd.d [file=/etc/xinetd.conf] [line=14] Dec 27 15:52:55 ccu3-webui daemon.crit xinetd[354]: 354 {init_services} no services. Exiting... Dec 27 15:52:55 ccu3-webui user.info root: Updating RF Lan Gateway Coprocessor Firmware Dec 27 15:52:55 ccu3-webui user.debug update-coprocessor: firmware filename is: coprocessor_update_hm_only.eq3 Dec 27 15:52:55 ccu3-webui user.info root: Updating RF Lan Gateway Firmware Dec 27 15:52:55 ccu3-webui user.info update-lgw-firmware: No gateway found in config file /etc/config/rfd.conf Dec 27 15:53:31 ccu3-webui user.err rfd: XmlRpc transport error calling system.listMethods({"1007"}) on binary://127.0.0.1:31999/RPC2: Dec 27 15:53:31 ccu3-webui user.err rfd: XmlRpc transport error calling listDevices({"1007"}) on binary://127.0.0.1:31999/RPC2: Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:0","DUTY_CYCLE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: DUTY_CYCLE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:0","DUTY_CYCLE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:0","OPERATING_VOLTAGE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: OPERATING_VOLTAGE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:0","OPERATING_VOLTAGE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:0","OPERATING_VOLTAGE_STATUS"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: OPERATING_VOLTAGE_STATUS"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:0","OPERATING_VOLTAGE_STATUS"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:0","RSSI_DEVICE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: RSSI_DEVICE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:0","RSSI_DEVICE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:0","RSSI_PEER"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: RSSI_PEER"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:0","RSSI_PEER"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:0","UNREACH"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: UNREACH"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:0","UNREACH"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","ACTIVE_PROFILE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTIVE_PROFILE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","ACTIVE_PROFILE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","ACTUAL_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTUAL_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","ACTUAL_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","ACTUAL_TEMPERATURE_STATUS"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTUAL_TEMPERATURE_STATUS"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","ACTUAL_TEMPERATURE_STATUS"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","BOOST_TIME"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: BOOST_TIME"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","BOOST_TIME"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","FROST_PROTECTION"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: FROST_PROTECTION"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","FROST_PROTECTION"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","HEATING_COOLING"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HEATING_COOLING"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","HEATING_COOLING"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","HUMIDITY"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","HUMIDITY"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","HUMIDITY_STATUS"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY_STATUS"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","HUMIDITY_STATUS"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","PARTY_MODE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_MODE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","PARTY_MODE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","PARTY_SET_POINT_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_SET_POINT_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","PARTY_SET_POINT_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","PARTY_TIME_END"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_TIME_END"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","PARTY_TIME_END"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","PARTY_TIME_START"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_TIME_START"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","PARTY_TIME_START"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","QUICK_VETO_TIME"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: QUICK_VETO_TIME"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","QUICK_VETO_TIME"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","SET_POINT_MODE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SET_POINT_MODE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","SET_POINT_MODE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","SET_POINT_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SET_POINT_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","SET_POINT_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","SWITCH_POINT_OCCURED"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SWITCH_POINT_OCCURED"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","SWITCH_POINT_OCCURED"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:1","WINDOW_STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: WINDOW_STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:1","WINDOW_STATE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:8","EMERGENCY_OPERATION"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: EMERGENCY_OPERATION"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:8","EMERGENCY_OPERATION"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:8","FROST_PROTECTION"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: FROST_PROTECTION"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:8","FROST_PROTECTION"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:8","HUMIDITY_ALARM"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY_ALARM"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:8","HUMIDITY_ALARM"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:8","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:8","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:9","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:9","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:10","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:10","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:11","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:11","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124] Dec 27 15:53:31 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000C9A498FF399:12","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000C9A498FF399:12","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435] Dec 27 15:53:31 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]

pivccu-attach cat /var/log/hmserver.log Dec 27 15:53:02 de.eq3.lib.util.dynamics.GenericFactory INFO [main] @GenericFactory Dec 27 15:53:02 de.eq3.lib.util.dynamics.GenericFactory INFO [main] created instance of HMServerConfiguration with parameter(s) Dec 27 15:53:02 de.eq3.lib.util.dynamics.GenericFactory INFO [main] passed 1 parameter(s), in declarative order [String] Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [HMIPTRXWriterWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [KeyServerWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [KryoPersistenceWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [TransactionSubsystemHandler] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [FirmwareLoaderFileSystem] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LocalServerPersistentDataLoader] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LocalServerAdapterInitialization] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [BackendCommandHandler] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceInclusionAcceptHandler] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [CheckDeviceExistHandler] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [IncomingHMIPFrameHandler] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceBackgroundUpdateSubsystem] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceLiveUpdateSubsystem] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceInclusionDefaultConfigurationChanger] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [CyclicSmokeDetectorAwakening] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointElectroCardioGram] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LocalServerFirmwareUpdateInitialization] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointAuthorisationHandler] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointMessageDispatcher] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointWatchdog] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [WebSocketManager] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointCommDevice] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [RouterKeyServerWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointKeyServerWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [RemoteCommAdapterInitialization] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [RemoteCommAdapterFinalization] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LanRoutingWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyNotificationHandler] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyAPIWorker] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyBackendNotificationHandler] (3) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyBlindLevelCorrectionHandler] (1) worker Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyInitializion] (1) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: deploying 32 classes to Vert.x Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: 32 VertxDeployers initialized Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of AccessPointElectroCardioGram succeeded (b6b3e2f3-b31a-47aa-af28-714b21b7d9eb) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of HMIPTRXWriterWorker succeeded (0dc5b34e-6f11-4706-8fc5-6946609aeb20) Dec 27 15:53:08 de.eq3.cbcs.server.core.vertx.KeyServerWorker ERROR [vert.x-worker-thread-2] Missing key server configuration parameter (Network.Key) for mode: KEYSERVER_LOCAL Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of KeyServerWorker succeeded (16c2506a-a57d-4117-908a-2e1b3a86426d) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of TransactionSubsystemHandler succeeded (2e30fdd7-8054-48de-9c67-b513ca79b18b) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of LegacyBlindLevelCorrectionHandler succeeded (7dc83b59-ea8a-43fb-b2ec-d14fd72db50b) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of AccessPointKeyServerWorker succeeded (c01c4ae7-b6ab-49dd-8f77-2b2900992fa9) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of DeviceInclusionDefaultConfigurationChanger succeeded (997c6e77-60d0-4db9-b90e-61157b94ecaf) Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of CyclicSmokeDetectorAwakening succeeded (dda21b48-e6be-49da-88e8-05716ec9259b) Dec 27 15:53:08 de.eq3.cbcs.lib.remotecommadapter.device.security.RouterKeyServerWorker ERROR [vert.x-worker-thread-3] Missing key server configuration parameter (Network.Key) for mode: KEYSERVER_LOCAL Dec 27 15:53:08 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of RouterKeyServerWorker succeeded (6f9039cc-4332-4bcd-a72f-881af96baf5e) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of KryoPersistenceWorker succeeded (2de7a94f-b00d-4e8d-803e-44f4475edf38) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of LocalServerPersistentDataLoader succeeded (525ee338-e8df-4858-818f-25ed746c8ea1) Dec 27 15:53:09 de.eq3.cbcs.server.core.live_otau.DeviceLiveUpdateSubsystem INFO [vert.x-eventloop-thread-1] SYSTEM: DeviceLiveUpdateSubsystem started Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of CheckDeviceExistHandler succeeded (b8bdbf88-4df6-455e-ba5e-127856cf548f) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of DeviceLiveUpdateSubsystem succeeded (cd2c5d17-0c62-4c98-874f-244f55442ce4) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of DeviceBackgroundUpdateSubsystem succeeded (6d576925-cb4e-4a32-993c-034493e1368c) Dec 27 15:53:09 de.eq3.cbcs.server.core.otau.util.FirmwareLoaderFileSystem INFO [vert.x-worker-thread-4] SYSTEM: Firmware update directory is set to /etc/config/firmware Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of FirmwareLoaderFileSystem succeeded (c44cc9d8-16a6-44d3-984f-77587408d46f) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of IncomingHMIPFrameHandler succeeded (d6764566-4a5f-4b2e-83ff-fcdce2d4b121) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of DeviceInclusionAcceptHandler succeeded (d5279646-0246-4987-8c5b-89ff28971b35) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of AccessPointAuthorisationHandler succeeded (6c197e2f-89bf-49f6-9602-59fd97ed1043) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of WebSocketManager succeeded (2e36f280-e340-4604-8d2f-dcd8ebb15583) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of AccessPointMessageDispatcher succeeded (c0249ce8-4601-4175-a5d7-2e3add9d3f33) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of BackendCommandHandler succeeded (c357f9e8-f141-4a5a-94f0-5d910789a983) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of RemoteCommAdapterInitialization succeeded (4102a0dd-97fd-49c2-8ddd-371d1996f82f) Dec 27 15:53:09 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of AccessPointWatchdog succeeded (27016571-de7c-4e3e-a65b-9afe19620baa) Dec 27 15:53:10 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of LocalServerAdapterInitialization succeeded (6034077f-5b4f-4b8b-8a2e-1bba09c09bff) Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] TRX adapter state 1: HMIP_TRXApp Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] TRX adapter application is already running or started Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] No NWK, try to set address ... Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Try to set radio address 12032874... Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Set max send attempts for 3014F711A0001F58A9A727D5 to 3 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Try to get application version... Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Application version 4.0.20 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Bootloader version 1.0.1 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] hmos version 1.40.1 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] MCU type: CC1310 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Duty Cycle: 0.0 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] set DutyCycle limit to ffffffc8 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Set Duty Cycle Limit Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Current Security Counter: 47360 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Update security counter to calculation: 53114 Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] TRX adapter has no linkpartner Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Adapter with Access Point id 3014F711A0001F58A9A727D5 initialized Dec 27 15:53:10 de.eq3.cbcs.server.local.base.internal.LocalServerAdapterInitialization INFO [Thread-6] HMIPTRXInitialResponseListener said that Adapter was initialized Dec 27 15:53:11 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of LocalServerFirmwareUpdateInitialization succeeded (536d0070-e012-43ca-a9e3-3b91b4a8ae63) Dec 27 15:53:11 de.eq3.cbcs.server.core.otau.util.FirmwareLoaderFileSystem WARN [vert.x-worker-thread-4] SYSTEM: Firmware update directory in config file is no valid directory: /etc/config/firmware Dec 27 15:53:11 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO [vert.x-eventloop-thread-1] SYSTEM: Checking all devices on all accesspoints for updates Dec 27 15:53:11 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO [vert.x-eventloop-thread-1] SYSTEM: There are 0 APs queued with updatable devices (RF) Dec 27 15:53:11 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO [vert.x-eventloop-thread-1] SYSTEM: There are 0 APs queued with updatable devices (WIRED) Dec 27 15:53:11 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of AccessPointCommDevice succeeded (5096d4af-3cf6-4d74-b651-bd04043263db) Dec 27 15:53:11 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of RemoteCommAdapterFinalization succeeded (f5cb1239-c9b7-48be-8d2f-adac22cb7640) Dec 27 15:53:11 de.eq3.cbcs.lib.lanrouting.UdpServer INFO [vert.x-worker-thread-0] UDP Routing configuration: trying to bind port 43438 on eth0 0.0.0.0 -> 192.168.0.29 Dec 27 15:53:11 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of LegacyBackendNotificationHandler succeeded (56affc32-0e1b-446f-851d-70d45db97ccb) Dec 27 15:53:11 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of LegacyAPIWorker succeeded (3e862538-6553-43a3-be88-55dc588ecfda) Dec 27 15:53:11 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of LegacyNotificationHandler succeeded (2dff74de-4e9d-4d7f-a28f-ffa2b209cccb) Dec 27 15:53:12 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of LanRoutingWorker succeeded (c79a690a-1171-436c-bcc3-255e48998584) Dec 27 15:53:12 de.eq3.cbcs.lib.lanrouting.UdpServer INFO [vert.x-worker-thread-4] UDP Routing established on network interface eth0 : 0.0.0.0 (192.168.0.29) Dec 27 15:53:12 de.eq3.cbcs.lib.hmiptrxcommadapter.internal.RoutingSubsystem WARN [Thread-6] Received routing key A781220D5EE9CE74731C2A73E7F217F0 Dec 27 15:53:12 de.eq3.cbcs.lib.lanrouting.UdpServer INFO [vert.x-worker-thread-4] UDP Routing multi cast established on network interface eth0 : 192.168.0.29 Dec 27 15:53:12 de.eq3.cbcs.lib.remotecommadapter.AccessPointCommDevice INFO [vert.x-eventloop-thread-2] SYSTEM: Started Access Point WebSocket server with port 9293 Dec 27 15:53:12 de.eq3.cbcs.lib.remotecommadapter.AccessPointCommDevice INFO [vert.x-eventloop-thread-2] SYSTEM: connector open Dec 27 15:53:12 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of LegacyInitializion succeeded (8f429653-f9cd-4b2f-8c82-ba15d17a9253) Dec 27 15:53:12 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: initial deployment complete ____ Dec 27 15:53:12 de.eq3.cbcs.server.local.LocalServer INFO [Thread-0] SYSTEM: Bind XML-RPC api to port 32010 Dec 27 15:53:17 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default MaxEventLoopExecuteTime: 2000000000 Dec 27 15:53:17 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default BlockedThreadCheckInterval: 1000 Dec 27 15:53:17 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default MaxWorkerExecuteTime: 60000000000 Dec 27 15:53:17 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default EventLoopPoolSize: 8 Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [BackendWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [GroupRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [DiagramRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [StorageRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [DeviceFirmwareRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [EnergyPriceRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [CouplingRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [RegaClientWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [GroupConfigurationPersistenceFileSystem] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [HmIPGatewayManagementRequestWorker] (1) worker Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: deploying 10 classes to Vert.x Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: 10 VertxDeployers initialized Dec 27 15:53:17 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of BackendWorker succeeded (7615f039-8f44-4ef5-a1b9-b58dc7358c11) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of EnergyPriceRequestWorker succeeded (3f0b64c3-712b-4957-a331-538c7c7e0f75) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of CouplingRequestWorker succeeded (619d8105-4e08-43aa-919e-58713ece1a4a) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of RegaClientWorker succeeded (0f7c9c5e-05bc-44f6-bf43-f15f548e6845) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of StorageRequestWorker succeeded (35890da0-e464-4646-bb03-ab313ecb2c17) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of GroupConfigurationPersistenceFileSystem succeeded (6a0c43a2-c116-4494-beb5-8bfbe6806029) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of GroupRequestWorker succeeded (3d309d3c-8495-4c6b-90d8-5355fceca897) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of DiagramRequestWorker succeeded (b83435b6-0322-46a8-8b1e-b07414980df6) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of DeviceFirmwareRequestWorker succeeded (9da4ad58-4647-4b30-a51d-b303a10ea802) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of HmIPGatewayManagementRequestWorker succeeded (62f0d8fb-29b5-4a6e-8088-fa31b4615a69) Dec 27 15:53:18 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: initial deployment complete _____ Dec 27 15:53:18 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Starting HMServer at 127.0.0.1:39292 Dec 27 15:53:18 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Read Configuration Dec 27 15:53:18 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create Bidcos Dispatcher Dec 27 15:53:18 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] InitBidCosCache Dec 27 15:53:19 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create groupDefinitionProvider Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create VirtualDeviceHolder Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create VirtualDeviceHandlerRega Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create GroupAdministrationService Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create GroupDeviceDispatcher Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create GroupDeviceHandler Dec 27 15:53:20 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] @GroupDeviceHandler - initializing... Dec 27 15:53:20 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] --> created groupDeviceDispatcher (GroupDeviceService to BidCoS (via Dispatcher)) Dec 27 15:53:20 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] --> created virtualDeviceHandler (GroupDeviceService to ReGa) Dec 27 15:53:20 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] --> got groupDefinitionProvider Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create BidCosGroupMemberProvider Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init groupAdministrationService Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init Virtual OS Device Dec 27 15:53:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init ESHLight Bridge Dec 27 15:53:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create RrdDatalogging Dec 27 15:53:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create MeasurementService Dec 27 15:53:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init MeasurementService Dec 27 15:53:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create HTTP Server Dec 27 15:53:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create BidCos context and start handler Dec 27 15:53:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create group context and start handler Dec 27 15:53:21 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-1] (un)registerCallback on LegacyServiceHandler called from url: http://127.0.0.1:39292/bidcos Dec 27 15:53:21 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-0] init finished Dec 27 15:53:21 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO [vert.x-worker-thread-4] Added InterfaceId: HmIP-RF_java Dec 27 15:53:21 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO [vert.x-worker-thread-4] updateDevicesForClient HmIP-RF_java -> 66 device addresses will be added Dec 27 15:53:22 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Starting HMServer done Dec 27 15:53:31 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO [vert.x-eventloop-thread-5] (un)registerCallback on VirtualDeviceHandlerRega called from url: xmlrpc_bin://127.0.0.1:31999 Dec 27 15:53:31 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO [vert.x-eventloop-thread-5] Added InterfaceId: 1008 Dec 27 15:53:31 de.eq3.ccu.virtualdevice.service.internal.rega.BackendWorker INFO [vert.x-worker-thread-13] Execute BackendCommand: de.eq3.ccu.virtualdevice.service.internal.rega.BackendUpdateDevicesCommand Dec 27 15:53:41 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-4] (un)registerCallback on LegacyServiceHandler called from url: xmlrpc_bin://127.0.0.1:31999 Dec 27 15:53:41 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-2] init finished Dec 27 15:53:41 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO [vert.x-worker-thread-3] Added InterfaceId: 1009

pivccu-attach cat /var/hm_mode HM_HMIP_ADDRESS='' HM_HMIP_DEV='RPI-RF-MOD' HM_HMIP_DEVNODE='/dev/raw-uart' HM_HMIP_SERIAL='58A9A727D5' HM_HMIP_SGTIN='3014F711A0001F58A9A727D5' HM_HMIP_VERSION='4.0.20' HM_HMRF_ADDRESS='' HM_HMRF_DEV='RPI-RF-MOD' HM_HMRF_DEVNODE='/dev/raw-uart' HM_HMRF_SERIAL='58A9A727D5' HM_HMRF_VERSION='4.0.20' HM_HOST='rpi3' HM_HOST_GPIO_RESET='' HM_HOST_GPIO_UART='/dev/raw-uart' HM_LED_GREEN='' HM_LED_RED='' HM_LED_YELLOW='' HM_MODE='NORMAL' HM_RTC=''

alexreinert commented 4 years ago

Ist jetzt nicht weiter verwunderlich, in der original CCU (und damit auch in piVCCU) werden auf der Seite nur BidCos Geräte aufgelistet und keine HmIP Geräte.

chriss158 commented 4 years ago

Alles klar. Vielen Dank für die schnelle Antwort.