adding regs

[h-key]

can you help,look at my project file and me what's wrong, please

ESP12E_modified.zip

[h-key]

Here is what's in ESP12E_modified.zip Let me know, What and where I've went wrong. I looked at the examples and there is only one entry in each example, and its hard to see any pattern and I'm trying but it doesn't seem to be working for me

/* Modbus Andresarmento's ESP8266 Modbus */ include

include

include

//Modbus Registers Offsets (0-9999) const int SENSOR_IREG = 100; const int temp_ISTS = 101; // const int out11_COIL = 104; // these are regs? I figured this was reg numbers right? const int out22_COIL = 105; // and wasn't sure how this works const int out33_COIL = 106; // I was hoping you could help me here, tell me how,or const int out44_COIL = 107; // fix it and send it back to me (jcobern at gmx dot com) const int in55_COIL = 108; // this compiles, but that dosen't mean it work like it should. const int in66_COIL = 109; // also can you tell me the modbus address I will find these valves const int in77_COIL = 110; // any help you can give will be greatly appreciated const int in88_COIL = 111; // const int sensorValue = analogRead(A0); // in value const int tempPin = 16; // temp const int out11Pin = 12; // out on-off const int out22Pin = 13; // out on-off const int out33Pin = 14; // out on-off const int out44Pin = 6; // out on-off const int in55Pin = 7; // in on-off const int in66Pin = 8; // in on-off const int in77Pin = 9; // in on-off const int in88Pin = 10; // in on-off long ts;

//ModbusIP object ModbusIP mb;

void setup() {

Serial.begin(115200);

while (WiFi.status() != WL_CONNECTED) { delay(1500); Serial.print("."); }

Serial.print(WiFi.localIP());

ts = millis(); //Config Modbus IP mb.config("routername", "pw"); // it connect just fine, then show me the ip

//Set ledPin mode
pinMode(tempPin, INPUT);
pinMode(out11Pin, OUTPUT);
pinMode(out22Pin, OUTPUT);
pinMode(out33Pin, OUTPUT);
pinMode(out44Pin, OUTPUT);
pinMode(in55Pin, INPUT);
pinMode(in66Pin, INPUT);
pinMode(in77Pin, INPUT);
pinMode(in88Pin, INPUT);

// Add  register - Use addIsts() for digital inputs
mb.addIsts(temp_ISTS);
mb.addCoil(out11_COIL);
mb.addCoil(out22_COIL);
mb.addCoil(out33_COIL);
mb.addCoil(out44_COIL);
mb.addCoil(in55_COIL);
mb.addCoil(in66_COIL);
mb.addCoil(in77_COIL);
mb.addCoil(in88_COIL);

}

void loop() { //Call once inside loop() mb.task(); if (millis() > ts + 2000) { ts = millis();

//Attach Pins to registers mb.Ireg(SENSOR_IREG, analogRead(A0));
mb.Ists(temp_ISTS, analogRead(tempPin)); mb.Ists(out11_COIL, out11Pin); mb.Ists(out22_COIL, out22Pin); mb.Ists(out33_COIL, out33Pin); mb.Ists(out44_COIL, sensorValue); mb.Ists(in55_COIL, in55Pin); mb.Ists(in66_COIL, in66Pin);; mb.Ists(in77_COIL, in77Pin); mb.Ists(in88_COIL, in88Pin); }

Serial.println(tempPin); Serial.println(sensorValue / 83); delay(2000); // prints title with ending line break
//this print and delay stuff will be removed after testing

}

[ESP-O-MAT]

You add coils (mb.addCoil) and then use mb.Ists. You should use mb.Coil. For example: mb.Coil(out11_COIL, out11Pin);

Or you can use addIsts in setup: mb.addIsts(out11_COIL);