projector - Githubissues

Hi, I am writing- and I don't know if this project is dead or not so no worries if it is not supported. - I am building a DLP printer. I had it working on nanoDLP - but need to switch programs to be able to review what is happening on the printer. I came upon photonic, and installed. I have everything running except it would connect or does not understand the projector model. Is there any possibility you might be able to help?

mUVe printer RasPi4 Optoma UHD60 (4k) Arduino/Mega 2560 Marlin V2.0 (have 1.0 too if that is needed) DL from https://github.com/area515/Photonic3D

Thanks, Elliot

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your projector model. That's only when you want some advanced functions like controlling your printer to turn on/off through it's serial port.

Hi Wes, Thanks! I understand the printer commands and gcode. I have a mUVe printer that is heavily modified and was running on nanoDLP.

What I seem to be missing is the proper config file for the projector + raspios interface. I had this running on a ras pi3 with (noobs or jessielite), Optima uhd60 (4k), and RAMPS 1.4, MARLIN 1.0.

I'm trying to upgrade it to Raspi4, bullseye-lite, Marlin 2.0 or 1.0 (I have both working on NanoDLP).

It seems to be the config file, because I can get the printer online and interact with the GUI. It recognized the ramps board but I get an error on recognizing the projector.

I'm happy to share the config files etc

Any help is greatly appreciated.

Thanks!

On Thu, Oct 20, 2022, 7:48 PM Wes G. @.***> wrote:

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your project model. That only when you some advanced functions like controlling your printer to turn on/off through it's serial port.

— Reply to this email directly, view it on GitHub https://github.com/area515/Photonic3D/issues/359#issuecomment-1286282779, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHZKFKSINSFW3TVXUN4FLSTWEHK35ANCNFSM6AAAAAARJQBM7A . You are receiving this because you authored the thread.Message ID: @.***>

I wouldn't choose Automatic Projector detection. I would either use the RaspberryPi screen or even the Xwindows driver if it's detected. If you want to use the RaspberryPi drivers you need to make sure your configuration has them enabled: displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiMainLCDScreen=true displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiForceTVScreen=true

If you still have trouble detecting a screen, you'll need to start using my repo instead of area515 since it's quite a ways behind.

On Thu, Oct 20, 2022 at 7:24 PM elliot-mcallister @.***> wrote:

Hi Wes, Thanks! I understand the printer commands and gcode. I have a mUVe printer that is heavily modified and was running on nanoDLP.

What I seem to be missing is the proper config file for the projector + raspios interface. I had this running on a ras pi3 with (noobs or jessielite), Optima uhd60 (4k), and RAMPS 1.4, MARLIN 1.0.

I'm trying to upgrade it to Raspi4, bullseye-lite, Marlin 2.0 or 1.0 (I have both working on NanoDLP).

It seems to be the config file, because I can get the printer online and interact with the GUI. It recognized the ramps board but I get an error on recognizing the projector.

I'm happy to share the config files etc

Any help is greatly appreciated.

Thanks!

E

On Thu, Oct 20, 2022, 7:48 PM Wes G. @.***> wrote:

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your project model. That only when you some advanced functions like controlling your printer to turn on/off through it's serial port.

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286282779>, or unsubscribe < https://github.com/notifications/unsubscribe-auth/AHZKFKSINSFW3TVXUN4FLSTWEHK35ANCNFSM6AAAAAARJQBM7A

. You are receiving this because you authored the thread.Message ID: @.***>

— Reply to this email directly, view it on GitHub https://github.com/area515/Photonic3D/issues/359#issuecomment-1286305427, or unsubscribe https://github.com/notifications/unsubscribe-auth/AASP6NCM4CCTJPSBA2MDFQ3WEHPFDANCNFSM6AAAAAARJQBM7A . You are receiving this because you commented.Message ID: @.***>

Thanks Wes! I'll try your repo.

Best regards,

Elliot

On Thu, Oct 20, 2022, 9:56 PM Wes G. @.***> wrote:

I wouldn't choose Automatic Projector detection. I would either use the RaspberryPi screen or even the Xwindows driver if it's detected. If you want to use the RaspberryPi drivers you need to make sure your configuration has them enabled:

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiMainLCDScreen=true

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiForceTVScreen=true

If you still have trouble detecting a screen, you'll need to start using my repo instead of area515 since it's quite a ways behind.

On Thu, Oct 20, 2022 at 7:24 PM elliot-mcallister @.***> wrote:

Hi Wes, Thanks! I understand the printer commands and gcode. I have a mUVe printer that is heavily modified and was running on nanoDLP.

What I seem to be missing is the proper config file for the projector + raspios interface. I had this running on a ras pi3 with (noobs or jessielite), Optima uhd60 (4k), and RAMPS 1.4, MARLIN 1.0.

I'm trying to upgrade it to Raspi4, bullseye-lite, Marlin 2.0 or 1.0 (I have both working on NanoDLP).

It seems to be the config file, because I can get the printer online and interact with the GUI. It recognized the ramps board but I get an error on recognizing the projector.

I'm happy to share the config files etc

Any help is greatly appreciated.

Thanks!

E

On Thu, Oct 20, 2022, 7:48 PM Wes G. @.***> wrote:

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your project model. That only when you some advanced functions like controlling your printer to turn on/off through it's serial port.

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286282779 , or unsubscribe <

https://github.com/notifications/unsubscribe-auth/AHZKFKSINSFW3TVXUN4FLSTWEHK35ANCNFSM6AAAAAARJQBM7A

. You are receiving this because you authored the thread.Message ID: @.***>

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286305427>, or unsubscribe < https://github.com/notifications/unsubscribe-auth/AASP6NCM4CCTJPSBA2MDFQ3WEHPFDANCNFSM6AAAAAARJQBM7A

. You are receiving this because you commented.Message ID: @.***>

— Reply to this email directly, view it on GitHub https://github.com/area515/Photonic3D/issues/359#issuecomment-1286357745, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHZKFKVE7WJLBSMGBLLWSILWEHZ6PANCNFSM6AAAAAARJQBM7A . You are receiving this because you authored the thread.Message ID: @.***>

Hi Wes, Thank you for the help. If I switch repos I noticed you had a -Dev and a regular flavor. Is there any difference - would one be better for a DLP vs LCD?

Thanks again.

Best regards,

Elliot

phone: 540.759.2447

CONFIDENTIALITY NOTICE:

This electronic mail transmission is confidential, may be privileged and should be read or retained only by the intended recipient. If you have received this transmission in error, please immediately notify the sender and delete it from your system.cell: 540-759-2447

On Thu, Oct 20, 2022 at 9:56 PM Wes G. @.***> wrote:

I wouldn't choose Automatic Projector detection. I would either use the RaspberryPi screen or even the Xwindows driver if it's detected. If you want to use the RaspberryPi drivers you need to make sure your configuration has them enabled:

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiMainLCDScreen=true

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiForceTVScreen=true

If you still have trouble detecting a screen, you'll need to start using my repo instead of area515 since it's quite a ways behind.

On Thu, Oct 20, 2022 at 7:24 PM elliot-mcallister @.***> wrote:

Hi Wes, Thanks! I understand the printer commands and gcode. I have a mUVe printer that is heavily modified and was running on nanoDLP.

What I seem to be missing is the proper config file for the projector + raspios interface. I had this running on a ras pi3 with (noobs or jessielite), Optima uhd60 (4k), and RAMPS 1.4, MARLIN 1.0.

I'm trying to upgrade it to Raspi4, bullseye-lite, Marlin 2.0 or 1.0 (I have both working on NanoDLP).

It seems to be the config file, because I can get the printer online and interact with the GUI. It recognized the ramps board but I get an error on recognizing the projector.

I'm happy to share the config files etc

Any help is greatly appreciated.

Thanks!

E

On Thu, Oct 20, 2022, 7:48 PM Wes G. @.***> wrote:

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your project model. That only when you some advanced functions like controlling your printer to turn on/off through it's serial port.

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286282779 , or unsubscribe <

https://github.com/notifications/unsubscribe-auth/AHZKFKSINSFW3TVXUN4FLSTWEHK35ANCNFSM6AAAAAARJQBM7A

. You are receiving this because you authored the thread.Message ID: @.***>

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286305427>, or unsubscribe < https://github.com/notifications/unsubscribe-auth/AASP6NCM4CCTJPSBA2MDFQ3WEHPFDANCNFSM6AAAAAARJQBM7A

. You are receiving this because you commented.Message ID: @.***>

— Reply to this email directly, view it on GitHub https://github.com/area515/Photonic3D/issues/359#issuecomment-1286357745, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHZKFKVE7WJLBSMGBLLWSILWEHZ6PANCNFSM6AAAAAARJQBM7A . You are receiving this because you authored the thread.Message ID: @.***>

Hi Wes, I noted a -Dev and the other repo on your list is one more up to date?

I tried the wget command but my connection was refused. I will try again later today.

BTW, is it necessary to use wheezy still or is the new RasPiOS ok? I had installed BullsEye with the java modules to ge this far on the 515 repo.

Many thanks,

Best regards,

Elliot

phone: 540.759.2447

CONFIDENTIALITY NOTICE:

On Thu, Oct 20, 2022 at 9:56 PM Wes G. @.***> wrote:

I wouldn't choose Automatic Projector detection. I would either use the RaspberryPi screen or even the Xwindows driver if it's detected. If you want to use the RaspberryPi drivers you need to make sure your configuration has them enabled:

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiMainLCDScreen=true

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiForceTVScreen=true

If you still have trouble detecting a screen, you'll need to start using my repo instead of area515 since it's quite a ways behind.

On Thu, Oct 20, 2022 at 7:24 PM elliot-mcallister @.***> wrote:

Hi Wes, Thanks! I understand the printer commands and gcode. I have a mUVe printer that is heavily modified and was running on nanoDLP.

What I seem to be missing is the proper config file for the projector + raspios interface. I had this running on a ras pi3 with (noobs or jessielite), Optima uhd60 (4k), and RAMPS 1.4, MARLIN 1.0.

I'm trying to upgrade it to Raspi4, bullseye-lite, Marlin 2.0 or 1.0 (I have both working on NanoDLP).

It seems to be the config file, because I can get the printer online and interact with the GUI. It recognized the ramps board but I get an error on recognizing the projector.

I'm happy to share the config files etc

Any help is greatly appreciated.

Thanks!

E

On Thu, Oct 20, 2022, 7:48 PM Wes G. @.***> wrote:

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your project model. That only when you some advanced functions like controlling your printer to turn on/off through it's serial port.

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286282779 , or unsubscribe <

https://github.com/notifications/unsubscribe-auth/AHZKFKSINSFW3TVXUN4FLSTWEHK35ANCNFSM6AAAAAARJQBM7A

. You are receiving this because you authored the thread.Message ID: @.***>

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286305427>, or unsubscribe < https://github.com/notifications/unsubscribe-auth/AASP6NCM4CCTJPSBA2MDFQ3WEHPFDANCNFSM6AAAAAARJQBM7A

. You are receiving this because you commented.Message ID: @.***>

— Reply to this email directly, view it on GitHub https://github.com/area515/Photonic3D/issues/359#issuecomment-1286357745, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHZKFKVE7WJLBSMGBLLWSILWEHZ6PANCNFSM6AAAAAARJQBM7A . You are receiving this because you authored the thread.Message ID: @.***>

Hi Wes, I attempted to load this to my pi, and have a number of errors. I am happy to send the text of the messages but I may be missing something from the git repo: I am not a coder by any means and have little experience in RasPi. Any questions here that seem idiotic are because I have so little experience.

Thanks!

what java version are you using or does the program require - it looks like it is searching for a graphics packet for the config file but is not in the directed location?
seems that some items have been moved I get a 302 error - looks like they have been resolved by forwarding messages
missing startx and hostx commands, not sure if these are important 4., jdk-8u101-linux-arm32-vfp-hflt.tar.gz': No such file or directory - Is the repo for 32bit only?
tar (child): jdk-8u101-linux-arm32-vfp-hflt.tar.gz: Cannot open: No such file or directory tar (child): Error is not recoverable: exiting now tar: Child returned status 2 tar: Error is not recoverable: exiting now A new version of Java is available, please update this script with the proper download URLS from: http://www.oracle.com/technetwork/java/javase/downloads/index.html

Best regards,

Elliot

phone: 540.759.2447

CONFIDENTIALITY NOTICE:

On Mon, Oct 24, 2022 at 1:39 PM Elliot McAllister < @.***> wrote:

Hi Wes, I noted a -Dev and the other repo on your list is one more up to date?

I tried the wget command but my connection was refused. I will try again later today.

BTW, is it necessary to use wheezy still or is the new RasPiOS ok? I had installed BullsEye with the java modules to ge this far on the 515 repo.

Many thanks,

Best regards,

Elliot

phone: 540.759.2447

CONFIDENTIALITY NOTICE:

This electronic mail transmission is confidential, may be privileged and should be read or retained only by the intended recipient. If you have received this transmission in error, please immediately notify the sender and delete it from your system.cell: 540-759-2447

On Thu, Oct 20, 2022 at 9:56 PM Wes G. @.***> wrote:

I wouldn't choose Automatic Projector detection. I would either use the RaspberryPi screen or even the Xwindows driver if it's detected. If you want to use the RaspberryPi drivers you need to make sure your configuration has them enabled:

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiMainLCDScreen=true

displayDevice.org.area515.resinprinter.display.dispmanx.RaspberryPiForceTVScreen=true

If you still have trouble detecting a screen, you'll need to start using my repo instead of area515 since it's quite a ways behind.

On Thu, Oct 20, 2022 at 7:24 PM elliot-mcallister @.***> wrote:

Hi Wes, Thanks! I understand the printer commands and gcode. I have a mUVe printer that is heavily modified and was running on nanoDLP.

What I seem to be missing is the proper config file for the projector + raspios interface. I had this running on a ras pi3 with (noobs or jessielite), Optima uhd60 (4k), and RAMPS 1.4, MARLIN 1.0.

I'm trying to upgrade it to Raspi4, bullseye-lite, Marlin 2.0 or 1.0 (I have both working on NanoDLP).

It seems to be the config file, because I can get the printer online and interact with the GUI. It recognized the ramps board but I get an error on recognizing the projector.

I'm happy to share the config files etc

Any help is greatly appreciated.

Thanks!

E

On Thu, Oct 20, 2022, 7:48 PM Wes G. @.***> wrote:

You will need to build your own printer profile if you understand the commands your printer requires for each function. Place those gcode commands in those functions and away you go. It's not really that necessary to pick your project model. That only when you some advanced functions like controlling your printer to turn on/off through it's serial port.

— Reply to this email directly, view it on GitHub <

https://github.com/area515/Photonic3D/issues/359#issuecomment-1286282779 ,

or unsubscribe <

https://github.com/notifications/unsubscribe-auth/AHZKFKSINSFW3TVXUN4FLSTWEHK35ANCNFSM6AAAAAARJQBM7A

. You are receiving this because you authored the thread.Message ID: @.***>

— Reply to this email directly, view it on GitHub < https://github.com/area515/Photonic3D/issues/359#issuecomment-1286305427 , or unsubscribe < https://github.com/notifications/unsubscribe-auth/AASP6NCM4CCTJPSBA2MDFQ3WEHPFDANCNFSM6AAAAAARJQBM7A

. You are receiving this because you commented.Message ID: @.***>

— Reply to this email directly, view it on GitHub https://github.com/area515/Photonic3D/issues/359#issuecomment-1286357745, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHZKFKVE7WJLBSMGBLLWSILWEHZ6PANCNFSM6AAAAAARJQBM7A . You are receiving this because you authored the thread.Message ID: @.***>

area515 / Photonic3D

projector #359