search

arendst / Tasmota

Alternative firmware for ESP8266 and ESP32 based devices with easy configuration using webUI, OTA updates, automation using timers or rules, expandability and entirely local control over MQTT, HTTP, Serial or KNX. Full documentation at
https://tasmota.github.io/docs
GNU General Public License v3.0
22.08k stars 4.78k forks source link

Domoticz Multiple IDX for PWM Dimmers #2111

Closed jimpetre closed 6 years ago

jimpetre commented 6 years ago

Query more than an issue;

I'm using a Magichome/Arilux controller. Is there any way to assign individual IDX's to the relevant GPIO's as per board pinouts for PWM to allow separate control in domoticz?

Using a 'generic' module type IDX can be assigned to pin if selecting 'relay' as output type but there is no dimming control of this. at present i have the device configured as a Sonoff LED and this allows an IDX to be assigned but control is only possible for one GPIO

to be clear i don't want to control RGBW with the magic home but to drive separate Single color led strips as individual devices.

Thanks

gcannar commented 6 years ago

Same problem here! Flashed MagicHome with Tasmote, all ok! Created a virtual RGB in domoticz but i can control only the on off function , no colors no dimmer...how to set the IDX? Domoticz give me "32" for the RBG switch...and i set in Tasmota IDX to 32... But how to set other mqtt command sush color and dim? Domoticz have just one IDX for all the thing...

Some one can help me? :)

Thanks.

arendst commented 6 years ago

Does Domoticz support RGB with MQTT interface now? It didn't a few month ago...

jimpetre commented 6 years ago

I’m. It sure, I just want to be able to control all each gpio with a different idx... ie set a different dummy switch per pin assigned to an idx defined in the web interface / user config.h

jimpetre commented 6 years ago

Sorry that reply wasn’t very clear. I have no desire to control RGB, (searching through previous issues this doesn’t seem possible with Domoticz) but... I’d like to control dimming for each mosfet channel of the magic Home as an individual device.

If you select ‘Relay’ as ‘type’ in the web config it gives you an idx to configure with Domoticz but selecting PWM it doesn’t. Is there any way to do this?

arendst commented 6 years ago

Dimming for each channel will be possible from release 5.12.0h using command channel 0..100

jimpetre commented 6 years ago

You da man!

On 20 Mar 2018 15:15, "Theo Arends" notifications@github.com wrote:

Dimming for each channel will be possible from release 5.12.0h using command channel 0..100

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/arendst/Sonoff-Tasmota/issues/2111#issuecomment-374635706, or mute the thread https://github.com/notifications/unsubscribe-auth/Ajd8L0utoZSYngqcJX-ne5lyLKGS1MIBks5tgR0lgaJpZM4SjJS0 .

jimpetre commented 6 years ago

Still no way to assign different IDX's to PWM1,2,3,4,5? as you would with relay 1,2,3,4,5?

ascillato2 commented 6 years ago

Closing this issue as it is fixed.

mVik85 commented 3 years ago

Still no way to assign different IDX's to PWM1,2,3,4,5? as you would with relay 1,2,3,4,5?

If anyone would wonder about this (like me until 5 minutes ago), here the answer: https://github.com/emontnemery/domoticz_mqtt_discovery