arm64: dts: Add board FriendlyElec CM3588

[ColorfulRhino]

Hello!

This adds a dts file for the FriendlyElec CM3588 NAS as well as updates the nanopi-6-common dtsi, which is included in CM3588's dts, based on FriendlyElec's recent commits.

The following hardware features have been tested and are working with this dts:

• all 4 NVMe port, including their respective activity LEDs (NVMe tested with hdparm)
• EMMC
• HDMI 4k@60 (tested with Gnome desktop)
• LAN
• 2xUSB3, 1xUSB2 (USB-C and OTG/DP mode untested)
• hardware buttons (power, reset)
• hardware acceleration for video encoding/decoding (tested with jellyfin-ffmpeg6)

References: https://github.com/friendlyarm/kernel-rockchip/blob/1fddd62f9911d01edce8401fa5bc247d5e680914/arch/arm64/boot/dts/rockchip/rk3588-nanopi6-common.dtsi https://github.com/friendlyarm/kernel-rockchip/blob/nanopi6-v6.1.y/arch/arm64/boot/dts/rockchip/rk3588-nanopi6-rev09.dts

Hardware specs:

• SoC: Rockchip RK3588
  • CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
  • GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
  • VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
  • NPU: 6TOPs, supports INT4/INT8/INT16/FP16
• RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
• Flash: 0GB/64GB eMMC, at HS400 mode
• 1 x microSD interface, support up to SDR104 mode
• 1 x On-board PCIe 2.5G ethernet controller (RTL8125B)
• USB:
  • 2 x USB 3.1 Gen1 OTG which combo with DP display（up to 4Kp60）
  • 1 x USB 3.1 Gen1 Host
  • 2 x USB 2.0 Host
• PCIe:
  • up to 4 x PCIe interfaces
    • 2 x PCIe 2.1 x1 and 2 x PCIe 3.0 x2
    • or 2 x PCIe 2.1 x1 and 1 x PCIe 3.0 x4
    • or 1 x PCIe 2.1 x1, 1 x PCIe 3.0 x2, and 2 x PCIe 3.0 x1
    • or 4 x PCIe 3.0 x1
• HDMI output:
  • 2 x HDMI outputs which is compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
  • one support displays up to 7680x4320@60Hz, another one support up to 4Kp60
  • Support RGB/YUV(up to 10bit) format
• HDMI input: 1 x HDMI input, up to 4Kp60
• MIPI RX:
  • 2 x 4lane MIPI DPHY CSI RX which support x4 mode or x2+x2 mode ,compatible with MIPI V1.2
  • 2 x 4lane MIPI_D/CPHY_RX
• MIPI TX:
  • 2 x 4-lane MIPI D-PHY/C-PHY Combo PHY TX, compatible with MIPI DPHY 2.0 or CPHY 1.1
• Codec:
  • On-board ALC5616 Codec
  • 1 x stereo headphone output ( 20mW/CH, THD+N <= -80dB, 16Ohm Load )
  • 1 x single-end microphone input
• GPIO:
  • up to 3 x SPIs, 7 x UARTs, 6 x I2Cs, 15 x PWMs, 3 x I2Ss, 1 x SDIO, 81 x GPIOs
• others:
  • low power RTC (HYM8563TS) with backup battery input
  • Support 38Khz IR input
  • MASK button for eMMC update, reset button, Power button, and recovery mode button
  • Debug UART,3.3V level, 1500000bps
  • 2 x GPIO Controlled LED (SYS, LED1)
• Power supply: 5~20VDC input, 15W max
• PCB: 8 Layers, 55x65x1.6mm
• Stacking height: 6.6mm
• Connector: 4 x DF40C-100DP-0.4V(51), the mating connector is DF40HC(3.0)-100DS-0.4V(51)
• Ambient Operating Temperature: 0℃ to 70℃