search

arnemauer / Ducobox-ESPEasy-Plugin

Plugin voor ESPEasy om een Ducobox Silent / Focus / WTW Energy Comfort aan te sturen en sensoren uit te lezen. Er zijn twee plugins: een ducobox RF gateway en ducobox serial gateway.
78 stars 16 forks source link

P151: Firmware 20220530 no fanspeed #110

Closed bartlauwers53 closed 2 years ago

bartlauwers53 commented 2 years ago

I've just updated my unit (Gateway 7A) to the latest firmware after having issues with the countdown time before. This seems to work fine now. EDIT: this value still hangs, this time on 325(before, it was 295 and 305 very ofte) for unknown reasons from time to time, but on other moments, 4720 is possible as well. I only expect this countdown time to become active when I manually set the unit to a temporary state (Low, Mid or High) which should last for 15 minutes(900 seconds). On the other side: I don't see a rpm value for the fanspeed anymore from the plugin DUCO Serial GW - FanSpeed. The value on the devices page remains 0. What I've tried:

The DUCO Serial Gateway device with the "Ventilation_Percentage" output seems to work fine. Could this be a bug? Seems partially the same as what @mpeek1995 describes?

arjan-io commented 2 years ago

Ik kan dit bevestigen (en heb daar reed mail contact over gehad). Ter toevoeging;

bartlauwers53 commented 2 years ago

Ook in de log onder tools staat de fanspeed hier op 0.

arnemauer commented 2 years ago

Ik ga er deze week naar kijken :)

bartlauwers53 commented 2 years ago

Thanks. Ik ben even op vakantie dus zal pas na de 27e kunnen checken.

arnemauer commented 2 years ago

Wanneer je in de plugin "Log serial messages to syslog" aanzet in de plugin "DUCO Serial Gateway". Wat zien jullie dan terug in de weblog?

bartlauwers53 commented 2 years ago

Bij mij dit: 570393: EVENT: Clock#Time=Mon,09:32 571949: WD : Uptime 10 ConnectFailures 0 FreeMem 15664 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init 600645: EVENT: DUCO_VG_RF#Ventmode=3 600722: EVENT: SERGW_CO2#CO2_PPM=449 600766: EVENT: SERGW_Box_TempVocht#Temperature=21.9 600767: EVENT: SERGW_Box_TempVocht#Relative_humidity=46.24 600835: EVENT: SERGW_countdown#Countdown=420 600875: EVENT: SERGW_FanPercentage#Ventilation_Percentage=100.00 600912: EVENT: SERGW_FanSpeed#FanSpeed=0 600932: [P152] DUCO BOX SENSOR: CO2 PPM: 520 = 520 PPM 601614: [P153] DUCO BOX SENSOR: RH: 4624 = 46.24% 601615: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C 601949: WD : Uptime 10 ConnectFailures 0 FreeMem 17360 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init 612481: EVENT: SERGW_VentMode#Ventilationmode=3 612625: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END 612626: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END 613401: EVENT: SERGW_countdown#Countdown=290

arjan-io commented 2 years ago

Ik heb dit voor de 'gewone' log (dus niet met debug enabled). De fanspeed stond voor ik de log opende al dagen op 362rpm.

1547221917: WD   : Uptime 25787 ConnectFailures 0 FreeMem 18256 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
1547229471: [P150] RF GW: UPDATE by PLUGIN_READ
1547236308: [P156] DUCO FanSpeed: start read, eventid:6
1547236308: [P156] DUCO FanSpeed: Start reading fanspeed
1547236489: [P156] DUCO FanSpeed: Received correct response on fanspeed
1547236495: [P156] DUCO FanSpeed: Fanspeed: 2045 RPM
1547236495: [P156] DUCO FanSpeed: End of message received.
1547236495: [P156] DUCO FanSpeed: Stop reading from serial
1547246171: [P151] DUCO SER GW: Start readNetworkList
1547246322: [P151] DUCO SER GW: Received correct response on network
1547246335: [P151] DUCO SER GW: Send command successfull!
1547246362: [P151] DUCO SER GW: Ducobox row found!
1547246363: [P151] DUCO SER GW: New Ventilationmode value: 3
1547246363: [P151] DUCO SER GW: New Countdown value: 800
1547246363: [P151] DUCO SER GW: New Ventilation_Percentage value: 100
1547246364: [P151] DUCO SER GW: New Current_Fan_Value value: 81
1547246422: [P151] DUCO SER GW: End of message received.
1547246422: [P151] DUCO SER GW: Stop reading from serial
1547247370: [P151] DUCO SER GW: New value for Countdown
1547251917: WD   : Uptime 25788 ConnectFailures 0 FreeMem 18312 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init

Met debug enabled heb ik het volgende:

1547401917: WD   : Uptime 25790 ConnectFailures 0 FreeMem 18152 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
1547409471: [P150] RF GW: UPDATE by PLUGIN_READ
1547426171: [P151] DUCO SER GW: Start readNetworkList
1547426322: [P151] DUCO SER GW: Received correct response on network
1547426337: [P151] DUCO SER GW: Send command successfull!
1547426362: [P151] DUCO SER GW: Ducobox row found!
1547426363: [P151] DUCO SER GW: New Ventilationmode value: 3
1547426363: [P151] DUCO SER GW: New Countdown value: 620
1547426363: [P151] DUCO SER GW: New Ventilation_Percentage value: 100
1547426364: [P151] DUCO SER GW: New Current_Fan_Value value: 81
1547426422: [P151] DUCO SER GW: End of message received.
1547426422: [P151] DUCO SER GW: Stop reading from serial
1547427369: [P151] DUCO SER GW: New value for Current_Fan_Value
1547427377: [P151] DUCO SER GW: New value for Countdown
1547431918: WD   : Uptime 25791 ConnectFailures 0 FreeMem 18496 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
1547443756: [P156] DUCO FanSpeed: start read, eventid:6
1547443756: [P156] DUCO FanSpeed: Start reading fanspeed
1547443922: [P156] DUCO FanSpeed: ROW: 1 bytes read:8
1547443923: [P156] DUCO FanSpeed: Pakket ontvangen: 66616E7370656564 END
1547443923: [P156] DUCO FanSpeed: Received correct response on fanspeed
1547443927: [P156] DUCO FanSpeed: ROW: 2 bytes read:51
1547443929: [P156] DUCO FanSpeed: Pakket ontvangen: 202046616E53706565643A2041637475616C2032303438205B72706D5D202D2046696C74657265642032303
1547443979:  END
1547443980: [P156] DUCO FanSpeed: Fanspeed: 2049 RPM
1547443980: [P156] DUCO FanSpeed: ROW: 3 bytes read:6
1547443981: [P156] DUCO FanSpeed: Pakket ontvangen: 2020446F6E65 END
1547443981: [P156] DUCO FanSpeed: ROW: 4 bytes read:2
1547443981: [P156] DUCO FanSpeed: Pakket ontvangen: 2020 END
1547443981: [P156] DUCO FanSpeed: End of message received.
1547443982: [P156] DUCO FanSpeed: Stop reading from serial
1547446011: [P154] DUCO Ext. CO2 Sensor: start read, eventid:5
1547446011: [P154] DUCO Ext. CO2 Sensor: Read external CO2 sensor.
1547446011: [P154] DUCO Ext. CO2 Sensor: Start read external sensor. NodeAddress: 2. Type: CO2
1547446331: [P154] DUCO Ext. CO2 Sensor: Command confirmed by ducobox
1547446344: [P154] DUCO Ext. CO2 Sensor: Send command successfull!
1547446371: [P154] DUCO Ext. CO2 Sensor: CO2 PPM: 417 = 417 PPM
1547446371: [P154] DUCO Ext. CO2 Sensor: End of message received.
1547446371: [P154] DUCO Ext. CO2 Sensor: Stop reading from serial
bartlauwers53 commented 2 years ago

Als ik in tools bij advanced nog de debuglog aanzet zie ik dit(en hierna ga ik op vakantie, en kan ik niet meer bij m’n lokale gateway ;-) ) 11465787: 11465778 - 11465787 = 9 11466107: 11466087 - 11466107 = 20 11466407: 11466396 - 11466407 = 11 11468867: 11468866 - 11468867 = 1 11469187: 11469175 - 11469187 = 12 11469487: 11469484 - 11469487 = 3 11471962: 11471953 - 11471962 = 9 11472282: 11472262 - 11472282 = 20 11472525: EVENT: SERGW_VentMode#Ventilationmode=0 11472591: 11472572 - 11472591 = 19 11472677: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END 11472678: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END 11472691: [P151] DUCO SER GW: Send command successfull! 11475051: 11475040 - 11475051 = 11 11475351: 11475349 - 11475351 = 2 11475671: 11475658 - 11475671 = 13 11478131: 11478128 - 11478131 = 3 11478451: 11478436 - 11478451 = 15 11478751: 11478745 - 11478751 = 6 11481231: 11481215 - 11481231 = 16 11481531: 11481524 - 11481531 = 7 11481851: 11481833 - 11481851 = 18 11484311: 11484303 - 11484311 = 8 11484631: 11484611 - 11484631 = 20 11484931: 11484920 - 11484931 = 11 11487391: 11487390 - 11487391 = 1 11487711: 11487699 - 11487711 = 12 11488011: 11488008 - 11488011 = 3 11490393: EVENT: Clock#Time=Mon,12:34 11490491: 11490478 - 11490491 = 13 11490791: 11490786 - 11490791 = 5 11491111: 11491096 - 11491111 = 15 11491948: WD : Uptime 192 ConnectFailures 0 FreeMem 18000 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init 11493571: 11493565 - 11493571 = 6 11493891: 11493874 - 11493891 = 17 11494191: 11494183 - 11494191 = 8 11496311: 11496306 - 11496311 = 5 11496671: 11496653 - 11496671 = 18 11496971: 11496961 - 11496971 = 10 11497271: 11497270 - 11497271 = 1 11499751: 11499740 - 11499751 = 11 11500051: 11500049 - 11500051 = 2 11500371: 11500358 - 11500371 = 13 11501111: 11501102 - 11501111 = 9 11502831: 11502828 - 11502831 = 3 11503151: 11503137 - 11503151 = 14 11503451: 11503446 - 11503451 = 5 11505931: 11505915 - 11505931 = 16 11506231: 11506224 - 11506231 = 7 11506551: 11506533 - 11506551 = 18 11509011: 11509002 - 11509011 = 9 11509331: 11509311 - 11509331 = 20 11509631: 11509620 - 11509631 = 11 11512100: 11512090 - 11512100 = 10 11512400: 11512398 - 11512400 = 2 11512720: 11512707 - 11512720 = 13 11515180: 11515177 - 11515180 = 3 11515500: 11515486 - 11515500 = 14 11515800: 11515795 - 11515800 = 5 11518280: 11518265 - 11518280 = 15 11518580: 11518573 - 11518580 = 7 11518900: 11518882 - 11518900 = 18 11520645: EVENT: DUCO_VG_RF#Ventmode=0 11520722: EVENT: SERGW_CO2#CO2_PPM=405 11520765: EVENT: SERGW_Box_TempVocht#Temperature=22.4 11520765: EVENT: SERGW_Box_TempVocht#Relative_humidity=48.04 11520836: EVENT: SERGW_countdown#Countdown=0 11520875: EVENT: SERGW_FanPercentage#Ventilation_Percentage=10.00 11520914: EVENT: SERGW_FanSpeed#FanSpeed=395 11520932: [P152] DUCO BOX SENSOR: CO2 PPM: 404 = 404 PPM 11521360: 11521352 - 11521360 = 8 11521616: [P153] DUCO BOX SENSOR: RH: 4800 = 48.00% 11521617: [P153] DUCO BOX SENSOR: TEMP: 224 = 22.4°C 11521680: 11521661 - 11521680 = 19 11521948: WD : Uptime 192 ConnectFailures 0 FreeMem 17712 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init 11521980: 11521970 - 11521980 = 10 11522571: [P156] DUCO FanSpeed: Pakket ontvangen: 66616E7370656564 END 11522574: [P156] DUCO FanSpeed: Pakket ontvangen: 202046616E53706565643A2041637475616C20333932205B72706D5D202D2046696C7465726564203339342 11522574: [P156] DUCO FanSpeed: Fanspeed: 394 RPM 11522575: [P156] DUCO FanSpeed: Pakket ontvangen: 2020446F6E65 END 11522575: [P156] DUCO FanSpeed: Pakket ontvangen: 2020 END 11524460: 11524440 - 11524460 = 20 11524760: 11524749 - 11524760 = 11 11525060: 11525058 - 11525060 = 2 11527540: 11527528 - 11527540 = 12 11527840: 11527836 - 11527840 = 4 11528160: 11528145 - 11528160 = 15 11530620: 11530615 - 11530620 = 5 11530940: 11530924 - 11530940 = 16 11531240: 11531233 - 11531240 = 7 11532481: EVENT: SERGW_VentMode#Ventilationmode=0 11532621: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END 11532622: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END 11532638: [P151] DUCO SER GW: Send command successfull! 11533716: 11533703 - 11533716 = 13 11534016: 11534012 - 11534016 = 4 11534336: 11534321 - 11534336 = 15 11536796: 11536790 - 11536796 = 6 11537116: 11537099 - 11537116 = 17 11537416: 11537408 - 11537416 = 8 11539896: 11539878 - 11539896 = 18 11540196: 11540187 - 11540196 = 9 11540496: 11540496 - 11540496 = 0 11541116: 11541114 - 11541116 = 2 11545916: 11545915 - 11545916 = 1 11546237: 11546224 - 11546236 = 12 11546536: 11546533 - 11546536 = 3 11549016: 11549003 - 11549016 = 13 11549316: 11549312 - 11549316 = 4 11549636: 11549621 - 11549636 = 15 11550393: EVENT: Clock#Time=Mon,12:35 11551948: WD : Uptime 193 ConnectFailures 0 FreeMem 17904 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init 11552096: 11552090 - 11552096 = 6 11552416: 11552399 - 11552416 = 17 11552716: 11552707 - 11552716 = 9 11555196: 11555178 - 11555196 = 18 11555496: 11555486 - 11555496 = 10 11555796: 11555795 - 11555796 = 1 11558276: 11558265 - 11558276 = 11 11558576: 11558574 - 11558576 = 2 11558896: 11558883 - 11558896 = 13 11561356: 11561353 - 11561356 = 3 11561676: 11561661 - 11561676 = 15 11561976: 11561970 - 11561976 = 6

arnemauer commented 2 years ago

Even voor de duidelijkheid, we hebben het hier over [P156] DUCO FanSpeed toch? Dat is de fan in RPM (rounds per minute). Niet over de cur_fan_value uit [P151] DUCO SER GW.

arnemauer commented 2 years ago

@arjan-io Welke waarde stond er op de devices pagina? In de log leest hij wel goed de waarde uit: > 2049 RPM

@bartlauwers53 Uit de logs haal ik dat hij wel goed de waarden uitleest:

11522574: [P156] DUCO FanSpeed: Fanspeed: 394 RPM

Maar je ziet die waarde in niet op de devices pagina?

arjan-io commented 2 years ago

Ah. Ik zie inderdaad dat het over 2 verschillende sensoren gaat.

Ik heb het inderdaad over de P156. Op de Device-pagina blijft de waarde staan die als laatste op de log-pagina voorbij is gekomen, voordat ik de log-pagina sluit. Als laatste heb ik de log-pagina bekeken waar de waarde 2049 uit kwam. Er staat nu nog steeds 2049 terwijl de ventmode op 0 staat en er ook geen aansturen plaats vind door de CO2 sensor.

Bij de P151 zie ik geen mogelijkheid om de Fanspeed uit te lezen. Alleen de Fan-value en vent percentage.

arnemauer commented 2 years ago

ESP_Easy_mega_20220630_custom_ESP8266_4M1M.zip

Willen jullie deze bin eens proberen? Is het probleem daarmee opgelost?

bartlauwers53 commented 2 years ago

ESP_Easy_mega_20220630_custom_ESP8266_4M1M.zip

Willen jullie deze bin eens proberen? Is het probleem daarmee opgelost?

Sorry voor de late reactie(vakantie) maar nog even een update: ik zag dus op vakantie in mijn home assistant(die ik wel op afstand kan benaderen) dat er ineens wel waarden verschenen bij de fanspeed van Plug-in 151. Eerder was dat dus niet zo, niet bij de devices pagina en ook niet in de logs. Inmiddels geconstateerd dat de waarde nu al drie dagen ongeveer op 353 rpm staat. Een reboot van de gateway lost dat niet op.

Wil de nieuwe build best testen maar moet even kijken wanneer ik daar aan toe kom.

arjan-io commented 2 years ago

Ik heb de firmware er op gezet. Bij mij nog steeds het zelfde met de Fanspeed (rpm, P156). Log openen, dan komt de update van de Fanspeed pas door.

In de log had ik dit:

284138: WD   : Uptime 5 ConnectFailures 0 FreeMem 15496 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
290054: 290052 - 290054 = 2
308008: 307997 - 308008 = 11
308328: 308313 - 308328 = 15
308330: [P150] RF GW: 0 - Ignore message, not our networkID.
308348: 308340 - 308348 = 8
308349: [P150] RF GW: 0 - Ignore message, not our networkID.
308409: [P150] RF GW: RX FIFO OVERFLOW -> idle, flush RX FIFO and switch to RX state.
308668: 308654 - 308668 = 14
308669: [P150] RF GW: 0 - Ignore message, not our networkID.
308988: 308971 - 308988 = 17
308989: [P150] RF GW: 0 - Ignore message, not our networkID.
309348: 309337 - 309348 = 11
309350: [P150] RF GW: 0 - Ignore message, not our networkID.
312884: [P150] RF GW: UPDATE by PLUGIN_READ
313144: [P151] DUCO SER GW: New Current_Fan_Value value: 36
313203: [P151] DUCO SER GW: End of message received.
313203: [P151] DUCO SER GW: Stop reading from serial
313590: [P151] DUCO SER GW: New value for Current_Fan_Value
313597: [P151] DUCO SER GW: New value for Countdown
313597: [P154] DUCO Ext. CO2 Sensor: start read, eventid:5
313597: [P154] DUCO Ext. CO2 Sensor: Read external CO2 sensor.
313597: [P154] DUCO Ext. CO2 Sensor: Start read external sensor. NodeAddress: 2. Type: CO2
313926: [P154] DUCO Ext. CO2 Sensor: Command confirmed by ducobox
313937: 313930 - 313937 = 7
313938: [P150] RF GW: 0 - Ignore message, not our networkID.
313939: [P154] DUCO Ext. CO2 Sensor: Send command successfull!
313966: [P154] DUCO Ext. CO2 Sensor: CO2 PPM: 440 = 440 PPM
313976: [P154] DUCO Ext. CO2 Sensor: End of message received.
313976: [P154] DUCO Ext. CO2 Sensor: Stop reading from serial
314012: 313959 - 314012 = 53
314139: WD   : Uptime 5 ConnectFailures 0 FreeMem 15624 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
314582: [P156] DUCO FanSpeed: start read, eventid:6
314583: [P156] DUCO FanSpeed: Start reading fanspeed
314763: [P156] DUCO FanSpeed: ROW: 1 bytes read:8
314764: [P156] DUCO FanSpeed: Pakket ontvangen: 66616E7370656564 END
314764: [P156] DUCO FanSpeed: Received correct response on fanspeed
314768: [P156] DUCO FanSpeed: ROW: 2 bytes read:51
314770: [P156] DUCO FanSpeed: Pakket ontvangen: 202046616E53706565643A2041637475616C2031303136205B72706D5D202D2046696C74657265642031303
314820:  END
314821: [P156] DUCO FanSpeed: Fanspeed: 1013 RPM
314829: [P156] DUCO FanSpeed: ROW: 3 bytes read:6
314830: [P156] DUCO FanSpeed: Pakket ontvangen: 2020446F6E65 END
314830: [P156] DUCO FanSpeed: ROW: 4 bytes read:2
314830: [P156] DUCO FanSpeed: Pakket ontvangen: 2020 END
314830: [P156] DUCO FanSpeed: End of message received.
314830: [P156] DUCO FanSpeed: Stop reading from serial

De Device-pagina update ook heel laat. De berichten via MQTT worden een stuk eerder verstuurd dan dat de waardes op de device-pagina worden weer gegeven. Uiteindelijk is bij mij MQTT het belangrijkst...

[Edit] MQTT-waardes komen bijna nog sneller door dan de tekst op de log-pagina. Maar als de log-pagina niet open staat, komt de waarde van P156 in z'n geheel niet door (device-pagina niet en MQTT niet). Althans, blijft dezelfde (oude) waarde houden en deze oude waarde wordt wel door via MQTT verstuurd. De Device pagina update ook niet zo snel. Ik heb tot 43 seconden gemeten vanaf het moment dat MQTT de nieuwe waardes door kreeg. Echter vind ik dit het minst belangrijk. Het is hoogstens irritant als je aan het debuggen gaat i.c.m. domotica software. Ik heb met deze versie wel veel meer keer een RX FIFO OVERFLOW gezien. Dat had ik met de vorige versie eigenlijk nooit.

@bartlauwers53 volgens deze wiki pagina moet de Fanspeed van P156 komen. P151 doet Current Fan value (relatieve percentage van het max haalbare) of Ventilation Percentage (Op hoeveel procent de fan draait van de max ingestelde RPM).

bartlauwers53 commented 2 years ago

@bartlauwers53 volgens deze wiki pagina moet de Fanspeed van P156 komen. P151 doet Current Fan value (relatieve percentage van het max haalbare) of Ventilation Percentage (Op hoeveel procent de fan draait van de max ingestelde RPM).

Thanks, I stand corrected! Mijn log laat volgens mij niet per actie zien met een [Pxxx] waarde welke plugin het is, maar er staat een Timestamp en dan "EVENT" gevolgd door . Er boven stond toen [P151] dus ik nam aan dat dat dan de Plugin was waar die waarde bij hoort. Inmiddels die nieuwe versie er op staan, maar blijft hetzelfde. Fanspeed blijft in de log (en op alle andere plekken) op 0. Voor de volledigheid nog een stukje log erbij:

60890: EVENT: SERGW_Box_TempVocht#Temperature=21.9
60892: EVENT: SERGW_Box_TempVocht#Relative_humidity=63.06
60927: EVENT: SERGW_FanSpeed#FanSpeed=0
60965: EVENT: SERGW_countdown#Countdown=0
60969: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END
60970: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END
61004: EVENT: SERGW_FanPercentage#Ventilation_Percentage=0.00
61526: EVENT: SERGW_FanPercentage#Ventilation_Percentage=37.00
61737: [P153] DUCO BOX SENSOR: RH: 6297 = 62.97%
61747: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C
61756: EVENT: SERGW_Box_TempVocht#Temperature=21.9
61758: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.97
61759: EVENT: SERGW_Box_TempVocht#Temperature=21.9
61759: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.97
62074: WD   : Uptime 1 ConnectFailures 0 FreeMem 14480 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
70520: EVENT: Clock#Time=Mon,08:04
92075: WD   : Uptime 2 ConnectFailures 0 FreeMem 15912 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
120774: EVENT: DUCO_VG_RF#Ventmode=0
120810: EVENT: SERGW_VentMode#Ventilationmode=0
120849: EVENT: SERGW_CO2#CO2_PPM=496
120892: EVENT: SERGW_Box_TempVocht#Temperature=21.9
120893: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.97
120927: EVENT: SERGW_FanSpeed#FanSpeed=0
120966: EVENT: SERGW_countdown#Countdown=0
120970: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END
120971: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END
121006: EVENT: SERGW_FanPercentage#Ventilation_Percentage=37.00
121528: EVENT: SERGW_FanPercentage#Ventilation_Percentage=36.00
121732: [P152] DUCO BOX SENSOR: CO2 PPM: 493 = 493 PPM
121745: EVENT: SERGW_CO2#CO2_PPM=493
122075: WD   : Uptime 2 ConnectFailures 0 FreeMem 15104 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
122733: [P153] DUCO BOX SENSOR: RH: 6294 = 62.94%
122742: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C
122751: EVENT: SERGW_Box_TempVocht#Temperature=21.9
122753: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.94
122754: EVENT: SERGW_Box_TempVocht#Temperature=21.9
122754: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.94
130519: EVENT: Clock#Time=Mon,08:05
152075: WD   : Uptime 3 ConnectFailures 0 FreeMem 16128 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
180892: EVENT: SERGW_Box_TempVocht#Temperature=21.9
180893: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.94
180926: EVENT: SERGW_FanSpeed#FanSpeed=0
180965: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END
180966: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END
180970: EVENT: SERGW_countdown#Countdown=0
181006: EVENT: SERGW_FanPercentage#Ventilation_Percentage=36.00
181529: EVENT: SERGW_FanPercentage#Ventilation_Percentage=35.00
181751: [P153] DUCO BOX SENSOR: RH: 6285 = 62.85%
181760: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C
181768: EVENT: SERGW_Box_TempVocht#Temperature=21.9
181774: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.85
181774: EVENT: SERGW_Box_TempVocht#Temperature=21.9
181774: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.85
182076: WD   : Uptime 3 ConnectFailures 0 FreeMem 13496 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
190519: EVENT: Clock#Time=Mon,08:06
212075: WD   : Uptime 4 ConnectFailures 0 FreeMem 15632 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
240776: EVENT: DUCO_VG_RF#Ventmode=0
240811: EVENT: SERGW_VentMode#Ventilationmode=0
240849: EVENT: SERGW_CO2#CO2_PPM=493
240890: EVENT: SERGW_Box_TempVocht#Temperature=21.9
240890: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.85
240926: EVENT: SERGW_FanSpeed#FanSpeed=0
240964: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END
240965: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END
240969: EVENT: SERGW_countdown#Countdown=0
241005: EVENT: SERGW_FanPercentage#Ventilation_Percentage=35.00
241745: [P152] DUCO BOX SENSOR: CO2 PPM: 488 = 488 PPM
241757: EVENT: SERGW_CO2#CO2_PPM=488
242074: WD   : Uptime 4 ConnectFailures 0 FreeMem 15448 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
242749: [P153] DUCO BOX SENSOR: RH: 6292 = 62.92%
242758: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C
242766: EVENT: SERGW_Box_TempVocht#Temperature=21.9
242770: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.92
242770: EVENT: SERGW_Box_TempVocht#Temperature=21.9
242771: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.92
250519: EVENT: Clock#Time=Mon,08:07
272074: WD   : Uptime 5 ConnectFailures 0 FreeMem 15632 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
300811: EVENT: SERGW_VentMode#Ventilationmode=0
300893: EVENT: SERGW_Box_TempVocht#Temperature=21.9
300893: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.92
300926: EVENT: SERGW_FanSpeed#FanSpeed=0
300964: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END
300965: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END
300969: EVENT: SERGW_countdown#Countdown=0
301005: EVENT: SERGW_FanPercentage#Ventilation_Percentage=35.00
301750: [P153] DUCO BOX SENSOR: RH: 6285 = 62.85%
301759: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C
301767: EVENT: SERGW_Box_TempVocht#Temperature=21.9
301771: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.85
301772: EVENT: SERGW_Box_TempVocht#Temperature=21.9
301772: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.85
302075: WD   : Uptime 5 ConnectFailures 0 FreeMem 13344 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
310519: EVENT: Clock#Time=Mon,08:08
332074: WD   : Uptime 6 ConnectFailures 0 FreeMem 16224 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
360775: EVENT: DUCO_VG_RF#Ventmode=0
360811: EVENT: SERGW_VentMode#Ventilationmode=0
360849: EVENT: SERGW_CO2#CO2_PPM=488
360893: EVENT: SERGW_Box_TempVocht#Temperature=21.9
360893: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.85
360926: EVENT: SERGW_FanSpeed#FanSpeed=0
360964: [P151] DUCO SER GW: ROW: 1 bytes read:7Pakket ontvangen: 6E6574776F726B END
360965: [P151] DUCO SER GW: ROW: 2 bytes read:10Pakket ontvangen: 20204E6574776F726B3A END
360968: EVENT: SERGW_countdown#Countdown=0
361005: EVENT: SERGW_FanPercentage#Ventilation_Percentage=35.00
361526: EVENT: SERGW_FanPercentage#Ventilation_Percentage=34.00
361736: [P152] DUCO BOX SENSOR: CO2 PPM: 488 = 488 PPM
361748: EVENT: SERGW_CO2#CO2_PPM=488
362074: WD   : Uptime 6 ConnectFailures 0 FreeMem 17872 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
362731: [P153] DUCO BOX SENSOR: RH: 6282 = 62.82%
362741: [P153] DUCO BOX SENSOR: TEMP: 219 = 21.9°C
362749: EVENT: SERGW_Box_TempVocht#Temperature=21.9
362752: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.82
362752: EVENT: SERGW_Box_TempVocht#Temperature=21.9
362752: EVENT: SERGW_Box_TempVocht#Relative_humidity=62.82
370519: EVENT: Clock#Time=Mon,08:09
392075: WD   : Uptime 7 ConnectFailures 0 FreeMem 17816 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init

Ik hoor graag of wat ik nog kan doen, of wat jullie aan info nodig hebben om die waarde wel weer inzichtelijk te krijgen. Misschien from scratch gateway opnieuw configureren?

arnemauer commented 2 years ago

@bartlauwers53 In jou log zie ik überhaupt geen regels met betrekking tot de fanspeed. SERGW_FanSpeed#FanSpeed=0 is van P151? Staat de weblog op "debug"?

bartlauwers53 commented 2 years ago

Staat de weblog op "debug"?

Nee, en dankje, dat helpt! Nogmaals (nu een kort stukje): 

1862075: WD   : Uptime 31 ConnectFailures 0 FreeMem 17344 WiFiStatus 3 ESPeasy internal wifi status: Conn. IP Init
1862519: [P156] DUCO FanSpeed: start read, eventid:4
1862519: [P156] DUCO FanSpeed: Start reading fanspeed
1862707: [P156] DUCO FanSpeed: ROW: 1 bytes read:8
1862708: [P156] DUCO FanSpeed: Pakket ontvangen: 66616E7370656564 END
1862708: [P156] DUCO FanSpeed: Received correct response on fanspeed
1862712: [P156] DUCO FanSpeed: ROW: 2 bytes read:49
1862714: [P156] DUCO FanSpeed: Pakket ontvangen: 202046616E53706565643A2041637475616C20363837205B72706D5D202D2046696C7465726564203638372
1862714: [P156] DUCO FanSpeed: Fanspeed: 687 RPM
1862721: [P156] DUCO FanSpeed: ROW: 3 bytes read:6
1862722: [P156] DUCO FanSpeed: Pakket ontvangen: 2020446F6E65 END
1862722: [P156] DUCO FanSpeed: ROW: 4 bytes read:2
1862722: [P156] DUCO FanSpeed: Pakket ontvangen: 2020 END
1862722: [P156] DUCO FanSpeed: End of message received.
1862722: [P156] DUCO FanSpeed: Stop reading from serial
1862726: EVENT: SERGW_FanSpeed#FanSpeed=687
1870519: EVENT: Clock#Time=Mon,08:34

Sinds ik de weblog op "debug" heb gezet(stond op info) komen de rpm waarden wel gelijk door in de log en via MQTT. Bijzonder.

EDIT: waarde wordt ook alleen geüpdatet als de log open staat, en anders niet. In feite hetzelfde als wat @arjan-io ook omschrijft.

arnemauer commented 2 years ago

Ik denk dat dit het probleem is: https://github.com/arnemauer/Ducobox-ESPEasy-Plugin/blob/eb60c685c2589d9cce4892944aba9730230f4701/_P156_DucoSerialFanSpeed.ino#L108

serialPortInUseByTask = event->TaskIndex; is per ongeluk onder de if statement komen te staan waardoor plugin de seriele poort alleen kan "claimen" als je debug aan hebt.

arnemauer commented 2 years ago

Het is gefixt in de nieuwe binary: https://github.com/arnemauer/Ducobox-ESPEasy-Plugin/blob/master/Binaries/Binary%20based%20on%20ESPEasy_mega-20220427/20220704%20Firmware%20417d280%2004-07-2022%20(ESPEasy%20mega-20220427).bin

MPeek1995 commented 2 years ago

Dit lijkt te werken! Veel dank!

Rpm zie ik in log en in devices.

Op do 30 jun. 2022 om 20:43 schreef bartlauwers53 @.***

:

ESP_Easy_mega_20220630_custom_ESP8266_4M1M.zip https://github.com/arnemauer/Ducobox-ESPEasy-Plugin/files/9022327/ESP_Easy_mega_20220630_custom_ESP8266_4M1M.zip

Willen jullie deze bin eens proberen? Is het probleem daarmee opgelost?

Sorry voor de late reactie(vakantie) maar nog even een update: ik zag dus op vakantie in mijn home assistant(die ik wel op afstand kan benaderen) dat er ineens wel waarden verschenen bij de fanspeed van Plug-in 151. Eerder was dat dus niet zo, niet bij de devices pagina en ook niet in de logs. Inmiddels geconstateerd dat de waarde nu al drie dagen ongeveer op 353 rpm staat. Een reboot van de gateway lost dat niet op.

Wil de nieuwe build best testen maar moet even kijken wanneer ik daar aan toe kom.

— Reply to this email directly, view it on GitHub https://github.com/arnemauer/Ducobox-ESPEasy-Plugin/issues/110#issuecomment-1171554794, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHSPKR6DR7UUKPKQT7JEPHDVRXTDHANCNFSM5YUCIGOA . You are receiving this because you were mentioned.Message ID: @.***>