KubotaAtSeltech
commented
11 years ago I built L4T using other Toolchain (for hard float).
I downloaded that Toolchain from other place. It is not it in pbs-stage1 and pbs-stage2.
I copied L4T Kernel that is using other Toolchain to SD-Card. It was able to boot.
However, L4T Kernel stops on the way, but the situation is better than the thing mentioned above.
In this case I think that image of rootfs may have a problem.
U-Boot 2013.07-g69929c6 (Oct 16 2013 - 20:10:43)
TEGRA30
Board: Avionic Design Tamonten��™ NG Evaluation Carrier
DRAM: 1 GiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
mmc1 is current device
Scanning mmc 1...
** File not found /boot.scr.uimg **
273 bytes read in 35 ms (6.8 KiB/s)
boot.scr found! Executing ...
## Executing script at 90000000
3168072 bytes read in 320 ms (9.4 MiB/s)
## Booting kernel from Legacy Image at 90000000 ...
Image Name: Linux-3.1.10-tec-ng+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3168008 Bytes = 3 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
<6>Initializing cgroup subsys cpu
<5>Linux version 3.1.10-tec-ng+ (kubota@ubuntu) (gcc version 4.7.2 20120910 (prerelease) (crosstool-NG linar3
CPU: ARMv7 Processor [412fc099] revision 9 (ARMv7), cr=10c5387d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: tec_ng
<6>Tegra reserved memory:
LP0: 00000000 - 00000000
Bootloader framebuffer: 00000000 - 00000000
Bootloader framebuffer2: 00000000 - 00000000
Framebuffer: b6800000 - b6ffffff
2nd Framebuffer: b7000000 - b77fffff
Carveout: b8000000 - bfffffff
Vpr: 00000000 - 00000000
Memory policy: ECC disabled, Data cache writealloc
<7>On node 0 totalpages: 225024
<7>free_area_init_node: node 0, pgdat c0626820, node_mem_map c0809000
<7> Normal zone: 1728 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 194880 pages, LIFO batch:31
<7> HighMem zone: 576 pages used for memmap
<7> HighMem zone: 27840 pages, LIFO batch:7
<6>fuse_speedo_calib: ATE prog ver 4.0
<6>Tegra3: CPU Speedo ID 2, Soc Speedo ID 2<6>Tegra Revision: A03 SKU: 0xb1 CPU Process: 3 Core Process: 0
<6>tegra: PLLP fixed rate: 408000000
<4>Lowering sbus maximum rate from 378000000 to 334000000
<4>Lowering vi maximum rate from 470000000 to 425000000
<4>Lowering vde maximum rate from 600000000 to 520000000
<4>Lowering mpe maximum rate from 600000000 to 520000000
<4>Lowering 2d maximum rate from 600000000 to 520000000
<4>Lowering epp maximum rate from 600000000 to 520000000
<4>Lowering 3d maximum rate from 600000000 to 520000000
<4>Lowering 3d2 maximum rate from 600000000 to 520000000
<4>Lowering se maximum rate from 625000000 to 520000000
<4>Lowering host1x maximum rate from 300000000 to 267000000
<4>Lowering cbus maximum rate from 700000000 to 520000000
<4>Lowering pll_c maximum rate from 1400000000 to 1066000000
<4>Lowering ndflash maximum rate from 240000000 to 200000000
<4>Lowering sbc1 maximum rate from 160000000 to 100000000
<4>Lowering sbc2 maximum rate from 160000000 to 100000000
<4>Lowering sbc3 maximum rate from 160000000 to 100000000
<4>Lowering sbc4 maximum rate from 160000000 to 100000000
<4>Lowering sbc5 maximum rate from 160000000 to 100000000
<4>Lowering sbc6 maximum rate from 160000000 to 100000000
<4>Lowering dsia maximum rate from 500000000 to 432500000
<4>Lowering dsib maximum rate from 500000000 to 432500000
<4>Lowering cpu_g maximum rate from 1700000000 to 1400000000
<4>tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
<4>tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
<4>tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
<4>tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
<6>tegra dvfs: VDD_CPU nominal 1100mV, scaling enabled
<6>tegra dvfs: VDD_CORE nominal 1300mV, scaling enabled
<6>L310 cache controller enabled
<6>l2x0: 8 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e080001, Cache size: 1048576 B
<6>PERCPU: Embedded 7 pages/cpu @c1111000 s6272 r8192 d14208 u32768
<7>pcpu-alloc: s6272 r8192 d14208 u32768 alloc=8*4096
<7>pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 222720
<5>Kernel command line: mem=1024M console=ttyS0,115200n8 core_edp_mv=1300 root=LABEL=boot:/rootfs.img rootfso
<6>PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 872MB 7MB = 879MB total
<5>Memory: 881688k/881688k available, 166888k reserved, 113664K highmem
<5>Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff000000 - 0xffe00000 ( 14 MB)
vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0585564 (5622 kB)
.init : 0xc0586000 - 0xc05b5880 ( 191 kB)
.data : 0xc05b6000 - 0xc06283a0 ( 457 kB)
.bss : 0xc06283c4 - 0xc067ba70 ( 334 kB)
<6>Preemptible hierarchical RCU implementation.
<6>NR_IRQS:832
<6>sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
<6>Console: colour dummy device 80x30
<6>Calibrating delay loop... 1397.55 BogoMIPS (lpj=6987776)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys debug
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys freezer
<6>CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
<6>Brought up 4 CPUs
<6>SMP: Total of 4 processors activated (5590.22 BogoMIPS).
<6>devtmpfs: initialized
<6>print_constraints: dummy:
<6>NET: Registered protocol family 16
<6>host1x bus init
<6>Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
<6>tec_ng_edp_init: CPU regulator 6000 mA
<6>The debug console clock name is uartd_dbg
<6>serial8250.0: ttyS0 at MMIO 0x70006300 (irq = 122) is a Tegra
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.1.10-tec-ng+ (kubota@ubuntu) (gcc version 4.7.2 20120910 (prerelease) (crosst3
[ 0.000000] CPU: ARMv7 Processor [412fc099] revision 9 (ARMv7), cr=10c5387d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: tec_ng
[ 0.000000] Tegra reserved memory:
[ 0.000000] LP0: 00000000 - 00000000
[ 0.000000] Bootloader framebuffer: 00000000 - 00000000
[ 0.000000] Bootloader framebuffer2: 00000000 - 00000000
[ 0.000000] Framebuffer: b6800000 - b6ffffff
[ 0.000000] 2nd Framebuffer: b7000000 - b77fffff
[ 0.000000] Carveout: b8000000 - bfffffff
[ 0.000000] Vpr: 00000000 - 00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] fuse_speedo_calib: ATE prog ver 4.0
[ 0.000000] Tegra3: CPU Speedo ID 2, Soc Speedo ID 2
[ 0.000000] Tegra Revision: A03 SKU: 0xb1 CPU Process: 3 Core Process: 0
[ 0.000000] tegra: PLLP fixed rate: 408000000
[ 0.000000] Lowering sbus maximum rate from 378000000 to 334000000
[ 0.000000] Lowering vi maximum rate from 470000000 to 425000000
[ 0.000000] Lowering vde maximum rate from 600000000 to 520000000
[ 0.000000] Lowering mpe maximum rate from 600000000 to 520000000
[ 0.000000] Lowering 2d maximum rate from 600000000 to 520000000
[ 0.000000] Lowering epp maximum rate from 600000000 to 520000000
[ 0.000000] Lowering 3d maximum rate from 600000000 to 520000000
[ 0.000000] Lowering 3d2 maximum rate from 600000000 to 520000000
[ 0.000000] Lowering se maximum rate from 625000000 to 520000000
[ 0.000000] Lowering host1x maximum rate from 300000000 to 267000000
[ 0.000000] Lowering cbus maximum rate from 700000000 to 520000000
[ 0.000000] Lowering pll_c maximum rate from 1400000000 to 1066000000
[ 0.000000] Lowering ndflash maximum rate from 240000000 to 200000000
[ 0.000000] Lowering sbc1 maximum rate from 160000000 to 100000000
[ 0.000000] Lowering sbc2 maximum rate from 160000000 to 100000000
[ 0.000000] Lowering sbc3 maximum rate from 160000000 to 100000000
[ 0.000000] Lowering sbc4 maximum rate from 160000000 to 100000000
[ 0.000000] Lowering sbc5 maximum rate from 160000000 to 100000000
[ 0.000000] Lowering sbc6 maximum rate from 160000000 to 100000000
[ 0.000000] Lowering dsia maximum rate from 500000000 to 432500000
[ 0.000000] Lowering dsib maximum rate from 500000000 to 432500000
[ 0.000000] Lowering cpu_g maximum rate from 1700000000 to 1400000000
[ 0.000000] tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
[ 0.000000] tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
[ 0.000000] tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
[ 0.000000] tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
[ 0.000000] tegra dvfs: VDD_CPU nominal 1100mV, scaling enabled
[ 0.000000] tegra dvfs: VDD_CORE nominal 1300mV, scaling enabled
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e080001, Cache size: 1048576 B
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1111000 s6272 r8192 d14208 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 222720
[ 0.000000] Kernel command line: mem=1024M console=ttyS0,115200n8 core_edp_mv=1300 root=LABEL=boot:/rootfo
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 872MB 7MB = 879MB total
[ 0.000000] Memory: 881688k/881688k available, 166888k reserved, 113664K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0585564 (5622 kB)
[ 0.000000] .init : 0xc0586000 - 0xc05b5880 ( 191 kB)
[ 0.000000] .data : 0xc05b6000 - 0xc06283a0 ( 457 kB)
[ 0.000000] .bss : 0xc06283c4 - 0xc067ba70 ( 334 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:832
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.006272] Calibrating delay loop... 1397.55 BogoMIPS (lpj=6987776)
[ 0.096920] pid_max: default: 32768 minimum: 301
[ 0.100656] Mount-cache hash table entries: 512
[ 0.104461] Initializing cgroup subsys debug
[ 0.107988] Initializing cgroup subsys cpuacct
[ 0.111541] Initializing cgroup subsys freezer
[ 0.115186] CPU: Testing write buffer coherency: ok
[ 0.119436] CPU1: Booted secondary processor
[ 0.122883] CPU2: Booted secondary processor
[ 0.126321] CPU3: Booted secondary processor
[ 0.128352] Brought up 4 CPUs
[ 0.133869] SMP: Total of 4 processors activated (5590.22 BogoMIPS).
[ 0.136660] devtmpfs: initialized
[ 0.141492] print_constraints: dummy:
[ 0.145137] NET: Registered protocol family 16
[ 0.147515] host1x bus init
[ 0.153115] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.270922] tec_ng_edp_init: CPU regulator 6000 mA
[ 0.275114] The debug console clock name is uartd_dbg
[ 0.281303] serial8250.0: ttyS0 at MMIO 0x70006300 (irq = 122) is a Tegra
<6>console [ttyS0] enabled
[ 0.820748] console [ttyS0] enabled
<6>Clear bootloader IO dpd settings
[ 0.849892] Clear bootloader IO dpd settings
<4>LP2 in idle disabled
[ 0.856412] LP2 in idle disabled
<6>bio: create slab at 0
[ 1.449787] bio: create slab at 0
<6>vgaarb: loaded
[ 1.455838] vgaarb: loaded
<4>i2c-core: driver [tps6591x] using legacy suspend method
[ 1.463995] i2c-core: driver [tps6591x] using legacy suspend method
<4>i2c-core: driver [tps6591x] using legacy resume method
[ 1.475585] i2c-core: driver [tps6591x] using legacy resume method
<5>SCSI subsystem initialized
[ 1.484725] SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
[ 1.496078] usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
[ 1.506070] usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
[ 1.515583] usbcore: registered new device driver usb
<6>tegra-otg tegra-otg: otg transceiver registered
[ 1.525397] tegra-otg tegra-otg: otg transceiver registered
<6>tps6591x 4-002d: VERNUM is 02
[ 1.535238] tps6591x 4-002d: VERNUM is 02
<6>print_constraints: tps6591x_VIO: 1800 mV normal standby
[ 1.547756] print_constraints: tps6591x_VIO: 1800 mV normal standby
<6>print_constraints: tps6591x_VDD_1: 600 <--> 1500 mV at 600 mV normal standby
[ 1.564379] print_constraints: tps6591x_VDD_1: 600 <--> 1500 mV at 600 mV normal standby
<6>print_constraints: tps6591x_VDD_2: 1500 mV normal standby
[ 1.579967] print_constraints: tps6591x_VDD_2: 1500 mV normal standby
<6>print_constraints: tps6591x_VDDCTRL: 600 <--> 1400 mV at 1000 mV normal standby
[ 1.597028] print_constraints: tps6591x_VDDCTRL: 600 <--> 1400 mV at 1000 mV normal standby
<6>print_constraints: tps6591x_LDO_1: 1050 mV normal standby
[ 1.611560] print_constraints: tps6591x_LDO_1: 1050 mV normal standby
<6>set_supply: tps6591x_LDO_1: supplied by tps6591x_VDD_2
[ 1.623333] set_supply: tps6591x_LDO_1: supplied by tps6591x_VDD_2
<6>print_constraints: tps6591x_LDO_2: 1000 mV normal standby
[ 1.635721] print_constraints: tps6591x_LDO_2: 1000 mV normal standby
<6>print_constraints: tps6591x_LDO_3: 1000 mV normal standby
[ 1.648340] print_constraints: tps6591x_LDO_3: 1000 mV normal standby
<6>print_constraints: tps6591x_LDO_4: 1200 mV normal standby
[ 1.662486] print_constraints: tps6591x_LDO_4: 1200 mV normal standby
<6>print_constraints: tps6591x_LDO_5: 3300 mV normal standby
[ 1.675809] print_constraints: tps6591x_LDO_5: 3300 mV normal standby
<6>print_constraints: tps6591x_LDO_6: 1200 mV normal standby
[ 1.690071] print_constraints: tps6591x_LDO_6: 1200 mV normal standby
<6>set_supply: tps6591x_LDO_6: supplied by tps6591x_VIO
[ 1.701666] set_supply: tps6591x_LDO_6: supplied by tps6591x_VIO
<6>print_constraints: tps6591x_LDO_7: 1200 mV normal standby
[ 1.715488] print_constraints: tps6591x_LDO_7: 1200 mV normal standby
<6>set_supply: tps6591x_LDO_7: supplied by tps6591x_VIO
[ 1.727078] set_supply: tps6591x_LDO_7: supplied by tps6591x_VIO
<6>print_constraints: tps6591x_LDO_8: 1000 mV normal standby
[ 1.740888] print_constraints: tps6591x_LDO_8: 1000 mV normal standby
<6>set_supply: tps6591x_LDO_8: supplied by tps6591x_VIO
[ 1.752481] set_supply: tps6591x_LDO_8: supplied by tps6591x_VIO
<6>print_constraints: tps62361: 500 <--> 1770 mV at 1200 mV normal standby
[ 1.772090] print_constraints: tps62361: 500 <--> 1770 mV at 1200 mV normal standby
<6>Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 1.785497] Advanced Linux Sound Architecture Driver Version 1.0.24.
<6>print_constraints: fixed_reg_en_5v_cp: 5000 mV normal standby
[ 1.799562] print_constraints: fixed_reg_en_5v_cp: 5000 mV normal standby
<6>print_constraints: fixed_reg_en_soc: 1200 mV normal standby
[ 1.813593] print_constraints: fixed_reg_en_soc: 1200 mV normal standby
<6>print_constraints: fixed_reg_en_5v0: 5000 mV normal standby
[ 1.827432] print_constraints: fixed_reg_en_5v0: 5000 mV normal standby
<6>print_constraints: fixed_reg_en_ddr: 1500 mV normal standby
[ 1.841288] print_constraints: fixed_reg_en_ddr: 1500 mV normal standby
<6>print_constraints: fixed_reg_en_3v3_sys: 3300 mV normal standby
[ 1.855491] print_constraints: fixed_reg_en_3v3_sys: 3300 mV normal standby
<6>print_constraints: fixed_reg_en_vdd_bl: 5000 mV normal standby
[ 1.868615] print_constraints: fixed_reg_en_vdd_bl: 5000 mV normal standby
<6>print_constraints: fixed_reg_en_3v3_fuse: 3300 mV normal standby
[ 1.881835] print_constraints: fixed_reg_en_3v3_fuse: 3300 mV normal standby
<6>set_supply: fixed_reg_en_3v3_fuse: supplied by fixed_reg_en_3v3_sys
[ 1.895383] set_supply: fixed_reg_en_3v3_fuse: supplied by fixed_reg_en_3v3_sys
<6>print_constraints: fixed_reg_en_3v3_emmc: 3300 mV normal standby
[ 1.909031] print_constraints: fixed_reg_en_3v3_emmc: 3300 mV normal standby
<6>set_supply: fixed_reg_en_3v3_emmc: supplied by fixed_reg_en_3v3_sys
[ 1.922578] set_supply: fixed_reg_en_3v3_emmc: supplied by fixed_reg_en_3v3_sys
<6>print_constraints: fixed_reg_en_3v3_pex_hvdd: 3300 mV normal standby
[ 1.936602] print_constraints: fixed_reg_en_3v3_pex_hvdd: 3300 mV normal standby
<6>set_supply: fixed_reg_en_3v3_pex_hvdd: supplied by fixed_reg_en_3v3_sys
[ 1.950855] set_supply: fixed_reg_en_3v3_pex_hvdd: supplied by fixed_reg_en_3v3_sys
<6>print_constraints: fixed_reg_en_3v3_sata_hvdd: 3300 mV normal standby
[ 1.965298] print_constraints: fixed_reg_en_3v3_sata_hvdd: 3300 mV normal standby
<6>set_supply: fixed_reg_en_3v3_sata_hvdd: supplied by fixed_reg_en_3v3_sys
[ 1.979734] set_supply: fixed_reg_en_3v3_sata_hvdd: supplied by fixed_reg_en_3v3_sys
<6>print_constraints: fixed_reg_en_usb3_vbus_oc: 5000 mV normal standby
[ 1.994195] print_constraints: fixed_reg_en_usb3_vbus_oc: 5000 mV normal standby
<6>Switching to clocksource timer_us
[ 2.005049] Switching to clocksource timer_us
<6>Switched to NOHz mode on CPU #1
[ 2.012709] Switched to NOHz mSwitched to NOHz mode on CPU #2
<6>Switched to NOHz mode on CPU #0
<6>Switched to NOHz mode on CPU #3
[ 2.020128] Switched to NOHz mode on CPU #2
[ 2.023384] Switched to NOHz mode on CPU #0
[ 2.026639] Switched to NOHz mode on CPU #3
<6>nvmap_page_pool_init: nvmap uc page pool size=27552 pages[ 2.044682] nvmap_page_pool_init: nvmap uc pa8
[ 2.075046] nvmap_page_pool_init: nvmap pool = uc, highmem=27552, pool_size=27552,totalram=220422, freeras
[ 2.144835] nvmap_page_pool_init: nvmap wc page pool size=27552 pages<6>nvmap_page_pool_init: nvmap pool 0
[ 2.193590] nvmap_page_pool_init: nvmap pool = wc, highmem=756, pool_size=27552,totalram=220422, freeram=s
[ 2.270438] nvmap_page_pool_init: nvmap iwb page pool size=27552 pages<6>nvmap_page_pool_init: nvmap pool0
[ 2.319833] nvmap_page_pool_init: nvmap pool = iwb, highmem=0, pool_size=27552,totalram=220422, freeram=1)
[ 2.397062] tegra-nvmap tegra-nvmap: created carveout iram (255KiB)
<6>tegra-nvmap tegra-nvmap: created carveout generic-0 (131072KiB)
[ 2.410573] tegra-nvmap tegra-nvmap: created carveout generic-0 (131072KiB)
<6>NET: Registered protocol family 2
[ 2.426855] NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 2.437645] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 2.451644] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 2.465906] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
[ 2.479095] TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
[ 2.487873] TCP reno registered
<6>UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.496074] UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.507510] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>NET: Registered protocol family 1
[ 2.517450] NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
[ 2.527063] RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
[ 2.536781] RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
[ 2.545275] RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.555574] RPC: Registered tcp NFSv4.1 backchannel transport module.
<7>PCI: CLS 0 bytes, default 32
<6>host1x host1x: initialized
[ 2.568591] host1x host1x: initialized
<6>PMU: registered new PMU device of type 0
[ 2.576473] PMU: registered new PMU device of type 0
<6>Tegra auto-hotplug initialized: disabled
[ 2.585716] Tegra auto-hotplug initialized: disabled
<6>cpu-tegra: init EDP limit: 1200 MHz
[ 2.594301] cpu-tegra: init EDP limit: 1200 MHz
highmem bounce pool size: 64 pages
[ 2.614587] highmem bounce pool size: 64 pages
<6>ashmem: initialized
[ 2.621382] ashmem: initialized
<6>squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.629934] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>fuse init (API version 7.17)
[ 2.638927] fuse init (API version 7.17)
<6>msgmni has been set to 1500
[ 2.645888] msgmni has been set to 1500
<6>io scheduler noop registered (default)
[ 2.653837] io scheduler noop registered (default)
<6>mpe mpe: initialized
[ 2.661527] mpe mpe: initialized
<6>gr3d gr3d: initialized
[ 2.667816] gr3d gr3d: initialized
<6>gr2d gr2d: initialized
[ 2.674212] gr2d gr2d: initialized
<6>isp isp: initialized
[ 2.680032] isp isp: initialized
<6>tegradc tegradc.0: probed
[ 2.687203] tegradc tegradc.0: probed
<6>tegradc tegradc.0: probed
[ 2.693800] tegradc tegradc.0: probed
<6>nvhdcp: using "always on" policy.
[ 2.705104] nvhdcp: using "always on" policy.
<6>tegradc tegradc.1: probed
[ 2.712492] tegradc tegradc.1: probed
<6>tegradc tegradc.1: probed
[ 2.719079] tegradc tegradc.1: probed
<6>tegradc tegradc.1: display detected
[ 2.750973] tegradc tegradc.1: display detected
<6>tegra_uart.0: ttyHS0 at MMIO 0x70006000 (irq = 68) is a TEGRA_UART
[ 2.762341] tegra_uart.0: ttyHS0 at MMIO 0x70006000 (irq = 68) is a TEGRA_UART
<6>Registered UART port ttyHS0
[ 2.902338] Registered UART port ttyHS0
<6>tegra_uart.1: ttyHS1 at MMIO 0x70006040 (irq = 69) is a TEGRA_UART
[ 2.912642] tegra_uart.1: ttyHS1 at MMIO 0x70006040 (irq = 69) is a TEGRA_UART
<6>Registered UART port ttyHS1
[ 3.052334] Registered UART port ttyHS1
<6>tegra_uart.2: ttyHS2 at MMIO 0x70006200 (irq = 78) is a TEGRA_UART
[ 3.062634] tegra_uart.2: ttyHS2 at MMIO 0x70006200 (irq = 78) is a TEGRA_UART
<6>Registered UART port ttyHS2
[ 3.212335] Registered UART port ttyHS2
<6>Initialized tegra uart driver
[ 3.219302] Initialized tegra uart driver
<6>brd: module loaded
[ 3.227684] brd: module loaded
<6>loop: module loaded
[ 3.235239] loop: module loaded
<7>tegra-sata tegra-sata.0: version 1.0
<6>tegra-sata tegra-sata.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl TEGRA-SATA mode
[ 3.252165] tegra-sata tegra-sata.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl TEGRA-SATA mode
<6>tegra-sata tegra-sata.0: flags: 64bit ncq sntf pm led pio slum part apst
[ 3.268348] tegra-sata tegra-sata.0: flags: 64bit ncq sntf pm led pio slum part apst
<6>scsi0 : tegra-sata
[ 3.278799] scsi0 : tegra-sata
<6>ata1: SATA max UDMA/133 irq 55
[ 3.285188] ata1: SATA max UDMA/133 irq 55
<6>usbcore: registered new interface driver smsc95xx
[ 3.294819] usbcore: registered new interface driver smsc95xx
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.306269] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<7>ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
<6>tegra USB phy - inst[2] platform info:
[ 3.321774] tegra USB phy - inst[2] platform info:
<6>port_otg: no
[ 3.328102] port_otg: no
<6>has_hostpc: yes
[ 3.332442] has_hostpc: yes
<6>phy_interface: USB_PHY_INTF_UTMI
[ 3.338567] phy_interface: USB_PHY_INTF_UTMI
<6>op_mode: TEGRA_USB_OPMODE_HOST
[ 3.345994] op_mode: TEGRA_USB_OPMODE_HOST
<6>vbus_gpio: -1
[ 3.351713] vbus_gpio: -1
<6>vbus_reg: vdd_vbus_typea_usb
[ 3.357307] vbus_reg: vdd_vbus_typea_usb
<6>hot_plug: enabled
[ 3.363211] hot_plug: enabled
<6>remote_wakeup: enabled
[ 3.368603] remote_wakeup: enabled
<3>Timed out waiting for lock bit on pll pll_u[ 3.380212] Timed out waiting for lock bit on pll pll_u<6>tr
[ 3.393991] tegra-ehci tegra-ehci.2: Tegra EHCI Host Controller
<6>tegra-ehci tegra-ehci.2: new USB bus registered, assigned bus number 1
[ 3.406822] tegra-ehci tegra-ehci.2: new USB bus registered, assigned bus number 1
<7>tegra-ehci tegra-ehci.2: reset hcs_params 0x10011 dbg=0 ind cc=0 pcc=0 ordered ports=1
<7>tegra-ehci tegra-ehci.2: reset hcc_params 60006 thresh 0 uframes 256/512/1024 park LPM ppce
<7>tegra-ehci tegra-ehci.2: enable per-port change event
<7>tegra-ehci tegra-ehci.2: park 0
<7>tegra-ehci tegra-ehci.2: support lpm
<7>tegra-ehci tegra-ehci.2: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
<7>tegra-ehci tegra-ehci.2: ...powerup ports...
<6>tegra-ehci tegra-ehci.2: irq 129, io mem 0x7d008000
[ 3.484484] tegra-ehci tegra-ehci.2: irq 129, io mem 0x7d008000
<7>tegra-ehci tegra-ehci.2: init command 0018005 PPCEE(park)=0 ithresh=1 period=512 RUN
<6>tegra-ehci tegra-ehci.2: USB 2.0 started, EHCI 1.00
[ 3.514466] tegra-ehci tegra-ehci.2: USB 2.0 started, EHCI 1.00
<7>usb usb1: default language 0x0409
<7>usb usb1: udev 1, busnum 1, minor = 0
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.533558] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.546703] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: Tegra EHCI Host Controller
[ 3.558394] usb usb1: Product: Tegra EHCI Host Controller
<6>usb usb1: Manufacturer: Linux 3.1.10-tec-ng+ ehci_hcd
[ 3.568982] usb usb1: Manufacturer: Linux 3.1.10-tec-ng+ ehci_hcd
<6>usb usb1: SerialNumber: tegra-ehci.2
[ 3.578737] usb usb1: SerialNumber: tegra-ehci.2
<7>usb usb1: usb_probe_device
<7>usb usb1: configuration #1 chosen from 1 choice
<7>usb usb1: adding 1-0:1.0 (config #1, interface 0)
<7>hub 1-0:1.0: usb_probe_interface
<7>hub 1-0:1.0: usb_probe_interface - got id
<6>hub 1-0:1.0: USB hub found
[ 3.606175] hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
[ 3.612885] hub 1-0:1.0: 1 port detected
<7>hub 1-0:1.0: standalone hub
<7>hub 1-0:1.0: individual port power switching
<7>hub 1-0:1.0: individual port over-current protection
<7>hub 1-0:1.0: Single TT
<6>ata1: SATA link down (SStatus 0 SControl 300)
[ 3.636085] ata1: SATA link down (SStatus 0 SControl 300)
<7>hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
<7>hub 1-0:1.0: power on to power good time: 20ms
<7>hub 1-0:1.0: local power source is good
<7>hub 1-0:1.0: enabling power on all ports
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.665075] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<7>ohci_hcd: block sizes: ed 64 td 64
<6>Initializing USB Mass Storage driver...
[ 3.678729] Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
[ 3.688821] usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
[ 3.698498] USB Mass Storage support registered.
<6>using rtc device, tegra_rtc, for alarms[ 3.707269] using rtc device, tegra_rtc, for alarms<6>tegra_rtc0
[ 3.717725] tegra_rtc tegra_rtc: rtc core: registered tegra_rtc as rtc0
<5>tegra_rtc tegra_rtc: Tegra internal Real Time Clock
[ 3.729543] tegra_rtc tegra_rtc: Tegra internal Real Time Clock
<6>i2c /dev entries driver
[ 3.737993] i2c /dev entries driver
<6>Linux video capture interface: v2.00
[ 3.745676] Linux video capture interface: v2.00
<6>trpc_sema_init: registered misc dev 10:56
[ 3.754521] trpc_sema_init: registered misc dev 10:56
<7>tegra-ehci tegra-ehci.2: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
<7>hub 1-0:1.0: port 1: status 0101 change 0001
<6>trpc_node_register: Adding 'local' to node list
[ 3.776928] trpc_node_register: Adding 'local' to node list
<6>device-mapper: uevent: version 1.0.3
[ 3.786385] device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
[ 3.798756] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
<6>cpuidle: using governor ladder
[ 3.810677] cpuidle: using governor ladder
<6>cpuidle: using governor menu
[ 3.817960] cpuidle: using governor menu
<6>sdhci: Secure Digital Host Controller Interface driver
[ 3.827192] sdhci: Secure Digital Host Controller Interface driver
<6>sdhci: Copyright(c) Pierre Ossman
[ 3.836768] sdhci: Copyright(c) Pierre Ossman
<6>sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.845866] sdhci-pltfm: SDHCI platform and OF driver helper
<4>mmc0: Invalid maximum block size, assuming 512 bytes
[ 3.857721] mmc0: Invalid maximum block size, assuming 512 bytes
<6>mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA
[ 3.874412] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA
<7>hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
<6>sdhci-tegra sdhci-tegra.2: vddio_sd_slot regulator not found: -19. Assuming vddio_sd_slot is not required.
[ 3.896180] sdhci-tegra sdhci-tegra.2: vmmc1: Invalid maximum block size, assuming 512 bytes
[ 3.911953] mmc1: Invalid maximum block size, assuming 512 bytes
<7>hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
<6>mmc1: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA
[ 3.929629] mmc1: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA
<6>wm8903 0-001a: WM8903 revision C
[ 3.946472] wm8903 0-001a: WM8903 revision C
<7>tegra-ehci tegra-ehci.2: port 1 high speed
<7>tegra-ehci tegra-ehci.2: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
<6>mmc0: new high speed DDR MMC card at address 0001
[ 4.026372] mmc0: new high speed DDR MMC card at address 0001
<6>mmcblk0: mmc0:0001 H4G1d 3.60 GiB
[ 4.035996] mmcblk0: mmc0:0001 H4G1d 3.60 GiB
<6>mmcblk0boot0: mmc0:0001 H4G1d partition 1 2.00 MiB
[ 4.045678] mmcblk0boot0: mmc0:0001 H4G1d partition 1 2.00 MiB
<6>mmcblk0boot1: mmc0:0001 H4G1d partition 2 2.00 MiB
[ 4.056759] mmcblk0boot1: mmc0:0001 H4G1d partition 2 2.00 MiB
<6>usb 1-1: new high speed USB device number 2 using tegra-ehci
[ 4.068673] usb 1-1: new high speed USB device number 2 using tegra-ehci
<6> mmcblk0: unknown partition table
[ 4.079586] mmcblk0: unknown partition table
<6> mmcblk0boot1: unknown partition table
[ 4.092640] mmcblk0boot1: unknown partition table
<6> mmcblk0boot0: unknown partition table
[ 4.104063] mmcblk0boot0: unknown partition table
<7>tegra-ehci tegra-ehci.2: port 1 high speed
<7>tegra-ehci tegra-ehci.2: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
<6>asoc: wm8903-hifi <-> tegra30-i2s.1 mapping ok
[ 4.157739] asoc: wm8903-hifi <-> tegra30-i2s.1 mapping ok
<6>asoc: dit-hifi <-> tegra30-spdif mapping ok
[ 4.170007] asoc: dit-hifi <-> tegra30-spdif mapping ok
<6>input: tegra-wm8903 Mic Jack as /devices/platform/tegra-snd-wm8903.0/sound/card0/input0
[ 4.189211] input: tegra-wm8903 Mic Jack as /devices/platform/tegra-snd-wm8903.0/sound/card0/input0
<6>input: tegra-wm8903 Headphone Jack as /devices/platform/tegra-snd-wm8903.0/sound/card0/input1
[ 4.209184] input: tegra-wm8903 Headphone Jack as /devices/platform/tegra-snd-wm8903.0/sound/card0/input1
<6>ALSA device list:
[ 4.222939] ALSA device list:
<6> #0: tegra-wm8903
[ 4.229978] #0: tegra-wm8903
<6>TCP cubic registered
[ 4.237525] TCP cubic registered
<7>usb 1-1: udev 2, busnum 1, minor = 1
<6>usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 4.259394] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
<6>NET: Registered protocol family 10
[ 4.269682] NET: Registered protocol family 10
<6>usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.281427] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>IPv6 over IPv4 tunneling driver
[ 4.295357] IPv6 over IPv4 tunneling driver
<6>NET: Registered protocol family 17
[ 4.303401] NET: Registered protocol family 17
<7>usb 1-1: usb_probe_device
<7>usb 1-1: configuration #1 chosen from 1 choice
<6>8021q: 802.1Q VLAN Support v1.8
[ 4.318611] 8021q: 802.1Q VLAN Support v1.8
<7>usb 1-1: adding 1-1:1.0 (config #1, interface 0)
<5>Registering the dns_resolver key type
[ 4.331410] Registering the dns_resolver key type
<7>hub 1-1:1.0: usb_probe_interface
<7>hub 1-1:1.0: usb_probe_interface - got id
<6>VFP support v0.3: [ 4.345653] VFP support v0.3: <6>hub 1-1:1.0: USB hub found
[ 4.351333] hub 1-1:1.0: USB hub found
implementor 41 architecture 3 part 30 variant 9 rev 4
[ 4.360214] implementor 41 architecture 3 part 30 variant 9 rev 4
<5>Registering SWP/SWPB emulation handler
[ 4.370217] Registering SWP/SWPB emulation handler
<6>hub 1-1:1.0: 5 ports detected
[ 4.378095] hub 1-1:1.0: 5 ports detected
<7>hub 1-1:1.0: compound device; port removable status: FRRRR
<7>hub 1-1:1.0: individual port power switching
<6>mmc1: new high speed SDHC card at address b368
[ 4.403955] mmc1: new high speed SDHC card at address b368
<4>Disabling clocks left on by bootloader:
[ 4.413995] Disabling clocks left on by bootloader:
<4> audio_2x
[ 4.420296] audio_2x
<7>hub 1-1:1.0: individual port over-current protection
<4> audio4_2x
<6>mmcblk1: mmc1:b368 SDC 15.0 GiB
[ 4.429761] audio4_2x
<7>h[ 4.433259] mmcblk1: mmc1:b368 SDC 15.0 GiB
ub 1-1:1.0: TT per port
<7>hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
<4> audio3_2x
[ 4.4498<25] audio3_2x
4> audio2_2x
[ < 4.453868] audio2_2x
4> audio1_2x
[ < 4.457911] audio1_2x
4> audio0_2x
[ 4.46<1952] audio0_2x
4> audio
<[ 4.465635] audio
4> audio4
<[ 4.469061] audio4
4> audio3
[ <4.472573] audio3
4> audio2
<[ 4.476086] audio2
4> audio1
[ 4<.479598] audio1
4> audio0
[ 4.483111] audio0
<4> dsi2-fixed
<[ 4.486982] dsi2-fixed
4> dsi1-fixed
[ 4.491198] < dsi1-fixed
4> uartd
[ <4.494968] uartd
4> nor
[ <4.498125] nor
4> bsev
[ 4.5<01200] bsev
4> bsea
[ 4.50<4361] bsea
4> dam2
[ 4<.507522] dam2
4> fuse_burn
[ 4.51113<0] fuse_burn
4> cclk_lp
[< 4.514991] cclk_lp
4> pll_x_out0
<[ 4.518948] pll_x_out0
4> pll_d2_out0
[ 4.<523254] pll_d2_out0
4> pll_p_out2
[ < 4.527557] pll_p_out2
4> pll_c_out1
[ 4.5<31775] pll_c_out1
4> pll_m_out1
[ 4.535992] pll_m_out1
<6>CPU rate: 1200 MHz
[ 4.540657] CPU rate: 1200 MHtegra_fuse_program_init: no vdd_fuse. fuse write disabled
[ 4.549247] tegra_fuse_progrDVFS: Got RTC device name:rtc0
[ 4.558802] DVFS: Got RTC detegra_dvfs: vdd_cpu: stats above 1237 mV will be squashed
[ 4.568434] tegra_dvfs: vdd_cpu: stats above 1237 mV will be squashed
<7>hub 1-1:1.0: power on to power good time: 100ms
<7>hub 1-1:1.0: local power source is good
<7>hub 1-1:1.0: enabling power on all ports
<4>tegra3_dvfs: minimum cap.emc rate 750000000 requires 1300 mV<6> mmcblk1: p1 p2 p3
[ 4.593969] tegra3_dvfs: minimum cap.emc rate 750000000 requires 1300 mV
[ 4.596034] mmcblk1: p1 p2 p3
<6>tegra dvfs: tegra sysfs cap interface is initialized
[ 4.610958] tegra dvfs: tegra sysfs cap interface is initialized
<6>tegra_actmon.emc: Completed initialization (0)
[ 4.621723] tegra_actmon.emc: Completed initialization (0)
<6>tegra_actmon.avp: Completed initialization (0)
[ 4.631931] tegra_actmon.avp: Completed initialization (0)
<6>regulator_init_complete: tps6591x_LDO_4: disabling
[ 4.643271] regulator_init_complete: tps6591x_LDO_4: disabling
<6>regulator_init_complete: tps6591x_LDO_2: disabling
[ 4.654427] regulator_init_complete: tps6591x_LDO_2: disabling
<6>regulator_init_complete: tps6591x_VDD_1: disabling
[ 4.665554] regulator_init_complete: tps6591x_VDD_1: disabling
<6>tegra_rtc tegra_rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
[ 4.678809] tegra_rtc tegra_rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
<7>hub 1-1:1.0: port 1: status 0101 change 0001
<6>Waiting for root device LABEL=boot:/rootfs.img...
[ 4.696358] Waiting for root device LABEL=boot:/rootfs.img...
<7>usb 1-1: link qh256-0001/e1e1e7a0 start 1 [1/0 us]
<7>hub 1-1:1.0: state 7 ports 5 chg 0002 evt 0000
<7>hub 1-1:1.0: port 1, status 0101, change 0000, 12 Mb/s
<7>hub 1-1:1.0: port 1 not reset yet, waiting 10ms
<6>usb 1-1.1: new high speed USB device number 3 using tegra-ehci
[ 4.915542] usb 1-1.1: new high speed USB device number 3 using tegra-ehci
<7>usb 1-1.1: udev 3, busnum 1, minor = 2
<6>usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 5.039715] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
<6>usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.053033] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<7>usb 1-1.1: usb_probe_device
<7>usb 1-1.1: configuration #1 chosen from 1 choice
<7>usb 1-1.1: adding 1-1.1:1.0 (config #1, interface 0)
<7>smsc95xx 1-1.1:1.0: usb_probe_interface
<7>smsc95xx 1-1.1:1.0: usb_probe_interface - got id
<6>smsc95xx v1.0.4
[ 5.086189] smsc95xx v1.0.4
<6>smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-tegra-ehci.2-1.1, smsc95xx USB 2.0 Ethernet, 00:0c:32
[ 5.164558] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-tegra-ehci.2-1.1, smsc95xx USB 2.0 Ether2
soerengrunewald
I built Platform with reference to documents put in github below. "avionic-design/pbs-stage2/Documentation/"
The build of Platform succeeded. I built by HardFP.
I prepared an SD-Card, and then copied the kernel and rootfs to the SD-Card.
So, I put the SD-Card into the device and powerup.
However, Kernel does not boot properly.
After "Loading Kernel Image ... " was output, it does not work.
U-Boot 2013.07-g69929c6 (Oct 16 2013 - 20:10:43) TEGRA30 Board: Avionic Design Tamonten��™ NG Evaluation Carrier DRAM: 1 GiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 mmc1 is current device Scanning mmc 1... ** File not found /boot.scr.uimg ** 256 bytes read in 35 ms (6.8 KiB/s) boot.scr found! Executing ... ## Executing script at 90000000 5383764 bytes read in 489 ms (10.5 MiB/s) ## Loading kernel from FIT Image at 90000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: Linux Kernel 3.1.10-tec-ng+ Type: Kernel Image Compression: uncompressed Data Start: 0x900000e8 Data Size: 3170952 Bytes = 3 MiB Architecture: ARM OS: Linux Load Address: 0x00008000 Entry Point: 0x00008000 Hash algo: crc32 Hash value: a2571bbf Hash algo: sha1 Hash value: cd4fd743454fdf194eb5b08e4bae5cf248879c26 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading ramdisk from FIT Image at 90000000 ... Using 'config@1' configuration Trying 'ramdisk@1' ramdisk subimage Description: Initial Ramdisk Type: RAMDisk Image Compression: uncompressed Data Start: 0x90306490 Data Size: 2211408 Bytes = 2.1 MiB Architecture: ARM OS: Linux Load Address: 0x00300000 Entry Point: 0x00000038 Hash algo: crc32 Hash value: e6900df8 Hash algo: sha1 Hash value: c641d7be37454ed9be2a84b513fa2c13e4e49be8 Verifying Hash Integrity ... crc32+ sha1+ OK Loading Kernel Image ...