search

bancika / diy-layout-creator

multi platform circuit layout and schematic drawing tool
http://diy-fever.com
GNU General Public License v3.0
854 stars 99 forks source link

Pickup Phase (Error?) v4.37 #812

Open calebst23 opened 1 month ago

calebst23 commented 1 month ago

[https://raw.githubusercontent.com/calebst23/HSS-Super-Strat-Wiring-W-DPDT/main/StratProject.diy]

Hello, I believe there to be a computation error within the Guitar Analyzer. I am almost certain that in SuperSwitch position 3, the humbucker north and south coils are wired so that they are in the correct phase, however, the Analyzer says they are opposite phase to the rest of the guitar only in position 3. This seems odd, so I am submitting the file I am working on for your reference. If I am incorrect and the error is my fault, I would like to know as I am spinning my wheels like a crazy person! Thanks in advance; I love the program!

Right click the link above and "save link as"

bancika commented 1 month ago

In 9 cases out of 10 it's user/wiring error and I spend a ton of time debugging when it's not a software issue. Please double check the wiring on the pickups and the switch

On Thu, Mar 7, 2024, 17:27 Caleb @.***> wrote:

[ https://raw.githubusercontent.com/calebst23/HSS-Super-Strat-Wiring-W-DPDT/main/StratProject.diy ]

Hello, I believe there to be a computation error within the Guitar Analyzer. I am almost certain that in SuperSwitch position 3, the humbucker north and south coils are wired so that they are in the correct phase, however, the Analyzer says they are opposite phase to the rest of the guitar only in position 3. This seems odd, so I am submitting the file I am working on for your reference. If I am incorrect and the error is my fault, I would like to know as I am spinning my wheels like a crazy person! Thanks in advance; I love the program!

Right click the link above and "save link as"

— Reply to this email directly, view it on GitHub https://github.com/bancika/diy-layout-creator/issues/812, or unsubscribe https://github.com/notifications/unsubscribe-auth/ACXONCLGFFQ4SK5W6KPILXTYXCIPLAVCNFSM6AAAAABELKDUJCVHI2DSMVQWIX3LMV43ASLTON2WKOZSGE3TIMRWGIYDENA . You are receiving this because you are subscribed to this thread.Message ID: @.***>

calebst23 commented 1 month ago

Will do, thanks for the input!

calebst23 commented 1 month ago

I have spent over ten hours this week and two more today trying to figure out why the humbucker in super switch position 3 is reverse phase, and I cannot figure it out. the NETLIST shows everything connected correctly, but the analyzer shows the phase is flipped. I would not be mad if it was an error on my part, but the suffering needs to end :) When you have a chance, could you take a look? Thanks in advance.

bancika commented 1 month ago

Take a look at this...I think you need to flip middle and neck wires

Switch configuration: [K/N/B.ON1:SuperSwitch.3:SW1.ON1]
Connected node groups:    [0.015uF.1, Tone.2]   [0.015uF.2, Bridge.North Start, Bridge.South Finish, GND, Middle.South Finish, Neck.North Finish, Output Jack.Sleeve, Volume.3]    [Bridge.North Finish, Bridge.South Start, Neck.North Start, Output Jack.Tip, Volume.2]    [Tone.3, Volume.1]

calebst23 commented 1 month ago

So, when SW is on 1, that puts the humbucker in parallel and messes up any wiring. For super switch positions 1-4, S1 needs to be ON2. Sorry I did not clarify that earlier

calebst23 commented 1 month ago

Switch configuration: [K/N/B.ON1:SuperSwitch.3:SW1.ON2] Connected node groups: [0.015uF.1, Tone.2] [0.015uF.2, 550KΩ.2, 550KΩ.2, Bridge.North Finish, Bridge.North Start, Bridge.South Finish, GND, Middle.South Finish, Neck.North Finish, Output Jack.Sleeve, Volume.3] [550KΩ.1, Bridge.South Start, Neck.North Start, Output Jack.Tip, Volume.2]   [550KΩ.1, Middle.South Start] [Tone.3, Volume.1]

bancika commented 1 month ago

Not sure, at this point it's easier to build it and verify :) I don't know how to help without burning hours and hours, it's a complicated diagram.

On Sat, Mar 9, 2024 at 8:47 PM Caleb @.***> wrote:

Switch configuration: [K/N/B.ON1:SuperSwitch.3:SW1.ON2] Connected node groups: [0.015uF.1, Tone.2] [0.015uF.2, 550KΩ.2, 550KΩ.2, Bridge.North Finish, Bridge.North Start, Bridge.South Finish, GND, Middle.South Finish, Neck.North Finish, Output Jack.Sleeve, Volume.3] [550KΩ.1, Bridge.South Start, Neck.North Start, Output Jack.Tip, Volume.2] [550KΩ.1, Middle.South Start] [Tone.3, Volume.1]

— Reply to this email directly, view it on GitHub https://github.com/bancika/diy-layout-creator/issues/812#issuecomment-1986960367, or unsubscribe https://github.com/notifications/unsubscribe-auth/ACXONCP54GWTQH2WXLECTQDYXNRO3AVCNFSM6AAAAABELKDUJCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSOBWHE3DAMZWG4 . You are receiving this because you commented.Message ID: @.***>

-- Branislav Stojkovic www.diy-fever.com

calebst23 commented 1 month ago

I agree with you on that. I'll let you know how it goes once parts arrive. Thanks again!