bb-qq
commented
2 years ago Could you try disabling auto-negotiation by ethtool -s eth2 speed 2500 duplex full autoneg off?
Closed ThoDieX closed 5 months ago
bb-qq
commented
2 years ago Could you try disabling auto-negotiation by ethtool -s eth2 speed 2500 duplex full autoneg off?
ThoDieX
commented
2 years ago Yes, had tried this several times but no success. Also not in the configuration file itself:
root@SchlumpfNAS:~# sudo ethtool -s eth2 speed 2500 duplex full autoneg off Cannot set new settings: Invalid argument not setting speed not setting duplex not setting autoneg
Seems that this is blocked even the command is available.
I have now tried it on an older DS415+. The adapter runs on this one as well. The same symptoms appear:
Adapter is recognized and switch shows 2.5Gb at startup.
Once startup is complete, STATUS stops flashing, then shortly thereafter the network disables (both LEDs on the switch's port are off) and after 5 seconds or so, activates at a random rate. Sometimes it is 100 Mbit (at the switch left off, right orange), sometimes it is 1000Mbit (at the switch left off, right green).
If I now want to have 2500Mbit, then I have to disconnect the LAN cable briefly and reconnect it again. Then the port LED left is green and right is off, a sign for 2500Mbit and in DSM itself is also.
After this all is fine and works very stable (no issued til now). It's only the start-up process ... on both NAS now.
bb-qq
commented
2 years ago One user reported that ethtool -s eth2 speed 1000 duplex full autoneg off disables auto-negotiation with 2.5 Gbps link, I'm not sure why, but it does seem to work for him. Try that command if you like.
ThoDieX
commented
2 years ago With speed 1000 it is working. But speed 2500 is ignored ... maybe of this (but the current speed is 2500Mb)
Link partner advertised link modes: 100baseT/Half 100baseT/Full
1000baseT/FullAlso it is shown in adapter features:
MyAdmin@SchlumpfNAS:~$ sudo ethtool eth2 Settings for eth2: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 2500baseX/Full Supported pause frame use: No Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 2500baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 2500Mb/s Duplex: Full Port: MII PHYAD: 32 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: yes
bb-qq
commented
2 years ago So, is your issue completely resolved?
ThoDieX
commented
2 years ago No, issue is still open.
Reducing to 1GB is possible but setting to 2.5Gb will be refused from the system. Maybe the driver has a problem fetching the speed from speed correctly after the cold boot in status "running". This seems to be the real issue.
ThoDieX
commented
2 years ago I've checked with 2.15.0-5 and tested another adapter (ASUS USB-C2500) but it's the same. Starting up fine unless status is "booted" and the LED not not blinking anymore. The network LED are complete off for 10 seconds and the wrong speed is negotated afterwards even it was correct before. Plugging out and in of the ethernet cable fixes this until next reboot.
Sjekke
commented
2 years ago I also have the 916+ but use the Plugable 2,5gbit adapter. When I look at my Asus router it's connected at 2,5gbit. Can I check something on my NAS to check if it's really the case?
ThoDieX
commented
2 years ago Hej Sjekke,
if the NAS tells you you have 2500Mb it's fine ... go to network in DSM and expand the network settings for your card., There you will see the speed.
ThoDieX
commented
2 years ago @bb-qq : I have connected the NAS with 2,5Gb to the AVM Repeater port and it works fine. So it must be a problem of the driver to negotiate the connection with the switch. I have also replaced the cables, too - no change. On a Windows machine and on a Raspberry Pi, there are no such problems with the switch and from boot I have negotiated a fixed 2500Mb.
Sjekke
commented
2 years ago Hej Sjekke,
if the NAS tells you you have 2500Mb it's fine ... go to network in DSM and expand the network settings for your card., There you will see the speed.
Ok, checked it and this is the case. 😀
bb-qq
commented
2 years ago I was expecting to disable auto-negotiation by running that command, keeping the link speed at 2500mbps. Even if we specified 1000mbps to the parameter of the command, this may be ignored and the speed remains 2500mbps in some environments.
The fact that it's working well on the PC suggests that it might be a power supply issue. In that case, using a Y-cable or a self-powered USB hub with an AC adapter may help.
ThoDieX
commented
2 years ago @bb-qq : I disagree with you. If this would be true, it has a problem during using it. But it is stable. If this is true it would have problems with other connections. But connected the DS916+ to my AVM Repeater 6000 it also runs well and has no problem at start up. It runs well on a low powered Raspberry Pi.
So at the and it is a problem of the driver in combination with the TP Link TL-SG108-M2 switch that after start-up (!) something went wrong on the handling out the speed (a second time!?). I don't know what DSM does to the USB port or how it handles the driver itself but fact is, it's not a power issue because running it on the same devices connected to other 2.5Gb connections/ports there are no problems.
--> Driver issue connecting to the switch
Sjekke
commented
2 years ago If it works well with your AVM repeater and a low powered RPI, why can't the problem be situated on your TP?
ThoDieX
commented
2 years ago By the process of elimination that failure analysts use to narrow down a failure and perhaps my 30+ professional years in IT with some gut feeling!?
Let's put it this way. Let's put it this way:
The error occurs with different adapters.
The error occurs on different NAS (DS916+ and DS415+)
The error occurs permanently under the same circumstances
The error does not occur when connected to other switches
The error occurs with two TP-Link switches but not with other devices.
This allows us to conclude the following:
This only allows the following results:
bb-qq
commented
2 years ago Thanks for the summary. I can understand from this situation that you think this is a driver issue. However, the Synology platform has various USB issues, especially with older models, so it's not surprising that this is happening.
In fact, the source code for my driver is straight from RealTek, and its contents are almost identical to the RaspberryPi's kernel driver. And the auto-negotiation is controlled by a few register values these do not vary at startup or not, and negotiation is done by the PHY. We can not configure details such as timeout. Because of this, I can not think of anything about modifying the driver. The only workaround I can think of is to disable auto-negotiation, sadly.
ThoDieX
commented
2 years ago All fine :-) ... it's just an "Sherlock Holmes" effect to figure it out ...
I've ordered an different switch from Zyxel with 8x 2,5Gb and I will tell if this is running better or not. If yes, maybe you can add a small warning in your FAQ abut TP-Link switche :-) ...
Thanks for helping!
Sjekke
commented
2 years ago If I read all the posts on this forum, I really can recommend the Plugable 2,5gbit adapter. Works like a charm ...
I hope the Zyxel does it job, I'm curious..
ThoDieX
commented
2 years ago So, Zyxel MG-108-ZZ0101F arrived and is working like charm now ... no problems anymore ... full 2.5Gb at all boot processes ...
Sjekke
commented
2 years ago If it works well with your AVM repeater and a low powered RPI, why can't the problem be situated on your TP?
So it was the TP switch?
ThoDieX
commented
2 years ago Not the switch alone, the combination of Realtek USB adapter + your driver + Synology NAS + TP Link switch at start up.
One last, rather cosmetic thing now is that when the NAS is shut down or booted, a message is sent that the NAS is no longer connected to Synology (quickconnect). But that is to get over and I have that even without the adapter in one of a hundred boot processes and can be turned off or ignored. Here the network connection is terminated faster than the rest of the system notices it and the system can tell Synology that there is only a reboot and no network failure. So this is not a matter for you.
jensche
commented
2 years ago Hello, I got the same issue. But in my case the adapter worked like a charm for 1 month. after 1 restart it just jumped down from 2.5gbit down to 100mbit.
Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 2500baseX/Full Supported pause frame use: No Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 32 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: yes
sudo ethtool -s eth2 speed 2500 duplex full autoneg off
is not working.
sudo ethtool -s eth2 speed 1000 duplex full autoneg on
is working
I've deinstalled the driver, restarted, then installed the driver again, and restarted. still not working.
I've tried all USB-Ports... Still only 100Mbit.
jensche
commented
2 years ago which is quite strange. it has worked 1 months without problems. After a reboot has no longer worked.
bb-qq
commented
2 years ago My reading of the driver code indicates that this device does not have the ability to lock the link speed to 2.5Gbps. So sadly sudo ethtool -s eth2 speed 2500 duplex full autoneg off will always fail in any environment.
I also searched Google and found many reports of Realtek chips giving link speeds of 100mbps. Some people said that replacing the cable solved the problem, while others got around it by fixing the link speed with an opposing switch. I can't think of anything else to try.
bb-qq
commented
5 months ago We now know how to disable autonegotiation on the driver side and use the following command:
sudo ethtool -s eth2 autoneg on advertise 0x802fhttps://github.com/bb-qq/r8152/wiki/Troubleshooting#fix-to-25gbps-r8152-specific
I would like to close this issue as it has not been commented on for a long time. If you have any questions, please create a new issue.
Description of the problem
After a shutdown and restart the negotiated speed at a TL-SG108-M2 is only 100 or 1000. It starts with 2.5Gb and after STATUS is stopping blinking (start fulfilled) the adapter is restarted (network off and on). After this I have only 100Mb or 1000Mb.
Diconnecting the network cable and reinserting it helps to negotiate at 2.5Gb until the system is restarted.
Problem with the swicth? Other network devices are working fine with this switch (Intel l255-v and a Fritz Repeater 6000).
Next to the adapter is an UPS but even w/o the UPS connected to the NAS it's always the same.
Description of your products
Description of your environment
Output of
dmesgcommand[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.108 (root@build17) (gcc version 7.5.0 (GCC) ) #42218 SMP Fri Sep 24 02:39:06 CST 2021 [ 0.000000] Command line: root=/dev/md0 ihd_num=4 netif_num=2 HddHotplug=1 SataPortMap=23 sata_remap=0>2:1>3:2>0:3>1 acpi_enforce_resources=lax libata.force=5:3.0G syno_hw_version=DS916+ vender_format_version=2 syno_hdd_detect=56,59,63,5 7 syno_hdd_enable=61,60,71,58 syno_usb_vbus_gpio=93@0000:00:14.0@2 KPTI_on sn=1640NZN335101 macs=0011325bbf09,0011325bbf 0a [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000006efff] usable [ 0.000000] BIOS-e820: [mem 0x000000000006f000-0x000000000006ffff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x0000000000070000-0x0000000000085fff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000086000-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007a4befff] usable [ 0.000000] BIOS-e820: [mem 0x000000007a4bf000-0x000000007aebefff] reserved [ 0.000000] BIOS-e820: [mem 0x000000007aebf000-0x000000007bfbefff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x000000007bfbf000-0x000000007bffefff] ACPI data [ 0.000000] BIOS-e820: [mem 0x000000007bfff000-0x000000007bffffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000027fffffff] usable [ 0.000000] e820: update [mem 0x01d87330-0x01d8733f] usable ==> usable [ 0.000000] extended physical RAM map: [ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000006efff] usable [ 0.000000] reserve setup_data: [mem 0x000000000006f000-0x000000000006ffff] ACPI NVS [ 0.000000] reserve setup_data: [mem 0x0000000000070000-0x0000000000085fff] usable [ 0.000000] reserve setup_data: [mem 0x0000000000086000-0x000000000009ffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x0000000001d8732f] usable [ 0.000000] reserve setup_data: [mem 0x0000000001d87330-0x0000000001d8733f] usable [ 0.000000] reserve setup_data: [mem 0x0000000001d87340-0x000000007a4befff] usable [ 0.000000] reserve setup_data: [mem 0x000000007a4bf000-0x000000007aebefff] reserved [ 0.000000] reserve setup_data: [mem 0x000000007aebf000-0x000000007bfbefff] ACPI NVS [ 0.000000] reserve setup_data: [mem 0x000000007bfbf000-0x000000007bffefff] ACPI data [ 0.000000] reserve setup_data: [mem 0x000000007bfff000-0x000000007bffffff] usable [ 0.000000] reserve setup_data: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fed01000-0x00000000fed01fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000027fffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] efi: EFI v2.40 by INSYDE Corp. [ 0.000000] efi: ACPI 2.0=0x7bffe014 SMBIOS=0x7a850000 [ 0.000000] efi: mem00: type=3, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB) [ 0.000000] efi: mem01: type=7, attr=0xf, range=[0x0000000000001000-0x000000000006f000) (0MB) [ 0.000000] efi: mem02: type=10, attr=0xf, range=[0x000000000006f000-0x0000000000070000) (0MB) [ 0.000000] efi: mem03: type=7, attr=0xf, range=[0x0000000000070000-0x0000000000086000) (0MB) [ 0.000000] efi: mem04: type=0, attr=0xf, range=[0x0000000000086000-0x0000000000088000) (0MB) [ 0.000000] efi: mem05: type=6, attr=0x800000000000000f, range=[0x0000000000088000-0x00000000000a0000) (0MB) [ 0.000000] efi: mem06: type=2, attr=0xf, range=[0x0000000000100000-0x0000000000ea2000) (13MB) [ 0.000000] efi: mem07: type=7, attr=0xf, range=[0x0000000000ea2000-0x000000003765e000) (871MB) [ 0.000000] efi: mem08: type=2, attr=0xf, range=[0x000000003765e000-0x0000000037b27000) (4MB) [ 0.000000] efi: mem09: type=7, attr=0xf, range=[0x0000000037b27000-0x00000000533fc000) (440MB) [ 0.000000] efi: mem10: type=2, attr=0xf, range=[0x00000000533fc000-0x000000007127e000) (478MB) [ 0.000000] efi: mem11: type=4, attr=0xf, range=[0x000000007127e000-0x000000007129e000) (0MB) [ 0.000000] efi: mem12: type=7, attr=0xf, range=[0x000000007129e000-0x0000000074256000) (47MB) [ 0.000000] efi: mem13: type=4, attr=0xf, range=[0x0000000074256000-0x00000000752b0000) (16MB) [ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x00000000752b0000-0x000000007541e000) (1MB) [ 0.000000] efi: mem15: type=1, attr=0xf, range=[0x000000007541e000-0x00000000754bf000) (0MB) [ 0.000000] efi: mem16: type=7, attr=0xf, range=[0x00000000754bf000-0x0000000077fae000) (42MB) [ 0.000000] efi: mem17: type=4, attr=0xf, range=[0x0000000077fae000-0x0000000077faf000) (0MB) [ 0.000000] efi: mem18: type=7, attr=0xf, range=[0x0000000077faf000-0x000000007804f000) (0MB) [ 0.000000] efi: mem19: type=4, attr=0xf, range=[0x000000007804f000-0x00000000794bf000) (20MB) [ 0.000000] efi: mem20: type=7, attr=0xf, range=[0x00000000794bf000-0x000000007a092000) (11MB) [ 0.000000] efi: mem21: type=2, attr=0xf, range=[0x000000007a092000-0x000000007a09b000) (0MB) [ 0.000000] efi: mem22: type=3, attr=0xf, range=[0x000000007a09b000-0x000000007a4bf000) (4MB) [ 0.000000] efi: mem23: type=5, attr=0x800000000000000f, range=[0x000000007a4bf000-0x000000007a6bf000) (2MB) [ 0.000000] efi: mem24: type=6, attr=0x800000000000000f, range=[0x000000007a6bf000-0x000000007aabf000) (4MB) [ 0.000000] efi: mem25: type=0, attr=0xf, range=[0x000000007aabf000-0x000000007aebf000) (4MB) [ 0.000000] efi: mem26: type=10, attr=0xf, range=[0x000000007aebf000-0x000000007bfbf000) (17MB) [ 0.000000] efi: mem27: type=9, attr=0xf, range=[0x000000007bfbf000-0x000000007bfff000) (0MB) [ 0.000000] efi: mem28: type=4, attr=0xf, range=[0x000000007bfff000-0x000000007c000000) (0MB) [ 0.000000] efi: mem29: type=7, attr=0xf, range=[0x0000000100000000-0x0000000280000000) (6144MB) [ 0.000000] efi: mem30: type=11, attr=0x8000000000000000, range=[0x00000000e00f8000-0x00000000e00f9000) (0MB) [ 0.000000] efi: mem31: type=11, attr=0x8000000000000000, range=[0x00000000fed01000-0x00000000fed02000) (0MB) [ 0.000000] efi: mem32: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x0000000100000000) (4MB) [ 0.000000] SMBIOS 2.8 present. [ 0.000000] DMI: Synology Inc. DS916+/Type2 - Board Product Name, BIOS M.215 3/2/2016 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] e820: last_pfn = 0x280000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect [ 0.000000] 1 base 000000000 mask F80000000 write-back [ 0.000000] 2 base 07E000000 mask FFE000000 uncachable [ 0.000000] 3 base 07D000000 mask FFF000000 uncachable [ 0.000000] 4 base 07C800000 mask FFF800000 uncachable [ 0.000000] 5 base 07C400000 mask FFFC00000 uncachable [ 0.000000] 6 base 100000000 mask F00000000 write-back [ 0.000000] 7 base 200000000 mask F80000000 write-back [ 0.000000] e820: last_pfn = 0x7c000 max_arch_pfn = 0x400000000 [ 0.000000] Base memory trampoline at [ffff88000007c000] 7c000 size 24576 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] BRK [0x01a3c000, 0x01a3cfff] PGTABLE [ 0.000000] BRK [0x01a3d000, 0x01a3dfff] PGTABLE [ 0.000000] BRK [0x01a3e000, 0x01a3efff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x27fe00000-0x27fffffff] [ 0.000000] [mem 0x27fe00000-0x27fffffff] page 2M [ 0.000000] BRK [0x01a3f000, 0x01a3ffff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x27c000000-0x27fdfffff] [ 0.000000] [mem 0x27c000000-0x27fdfffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x200000000-0x27bffffff] [ 0.000000] [mem 0x200000000-0x27bffffff] page 2M [ 0.000000] BRK [0x01a40000, 0x01a40fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x00100000-0x7a4befff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0x7a3fffff] page 2M [ 0.000000] [mem 0x7a400000-0x7a4befff] page 4k [ 0.000000] init_memory_mapping: [mem 0x7bfff000-0x7bffffff] [ 0.000000] [mem 0x7bfff000-0x7bffffff] page 4k [ 0.000000] BRK [0x01a41000, 0x01a41fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff] [ 0.000000] [mem 0x100000000-0x1ffffffff] page 2M [ 0.000000] RAMDISK: [mem 0x3765e000-0x37b26fff] [ 0.000000] ACPI: RSDP 0x000000007BFFE014 00024 (v02 INSYDE) [ 0.000000] ACPI: XSDT 0x000000007BFFE120 00094 (v01 INSYDE INSYDE 00000003 01000013) [ 0.000000] ACPI: FACP 0x000000007BFFA000 0010C (v05 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: DSDT 0x000000007BFE9000 0B0A1 (v02 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: FACS 0x000000007BFBB000 00040 [ 0.000000] ACPI: UEFI 0x000000007BFFD000 00236 (v01 INSYDE INSYDE 00000001 ACPI 00040000) [ 0.000000] ACPI: UEFI 0x000000007BFFB000 00042 (v01 INSYDE INSYDE 00000000 ACPI 00040000) [ 0.000000] ACPI: APIC 0x000000007BFF9000 00084 (v03 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: MCFG 0x000000007BFF8000 0003C (v01 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: SLIC 0x000000007BFF7000 00176 (v01 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: WDAT 0x000000007BFF6000 001C4 (v01 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: WDRT 0x000000007BFF5000 00047 (v01 INSYDE INSYDE 00000003 ACPI 00040000) [ 0.000000] ACPI: SSDT 0x000000007BFE8000 00763 (v01 INSYDE CpuPm 00003000 ACPI 00040000) [ 0.000000] ACPI: SSDT 0x000000007BFE7000 00290 (v01 INSYDE Cpu0Tst 00003000 ACPI 00040000) [ 0.000000] ACPI: SSDT 0x000000007BFE6000 0017A (v01 INSYDE ApTst 00003000 ACPI 00040000) [ 0.000000] ACPI: CSRT 0x000000007BFE5000 0014C (v00 INSYDE INSYDE 00000005 ACPI 00040000) [ 0.000000] ACPI: FPDT 0x000000007BFE4000 00044 (v01 INSYDE INSYDE 00000002 ACPI 00040000) [ 0.000000] ACPI: BGRT 0x000000007BFE3000 00038 (v01 INSYDE INSYDE 00000001 ACPI 00040000) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] [ffffea0000000000-ffffea0008bfffff] PMD -> [ffff880277600000-ffff88027e5fffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x27fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0006efff] [ 0.000000] node 0: [mem 0x00070000-0x00085fff] [ 0.000000] node 0: [mem 0x00100000-0x7a4befff] [ 0.000000] node 0: [mem 0x7bfff000-0x7bffffff] [ 0.000000] node 0: [mem 0x100000000-0x27fffffff] [ 0.000000] On node 0 totalpages: 2073668 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 22 pages reserved [ 0.000000] DMA zone: 3972 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 6793 pages used for memmap [ 0.000000] DMA32 zone: 496832 pages, LIFO batch:31 [ 0.000000] Normal zone: 21504 pages used for memmap [ 0.000000] Normal zone: 1572864 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-114 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 131 [ 0.000000] PM: Registered nosave memory: 000000000006f000 - 0000000000070000 [ 0.000000] PM: Registered nosave memory: 0000000000086000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 0000000001d87000 - 0000000001d88000 [ 0.000000] PM: Registered nosave memory: 0000000001d87000 - 0000000001d88000 [ 0.000000] PM: Registered nosave memory: 000000007a4bf000 - 000000007aebf000 [ 0.000000] PM: Registered nosave memory: 000000007aebf000 - 000000007bfbf000 [ 0.000000] PM: Registered nosave memory: 000000007bfbf000 - 000000007bfff000 [ 0.000000] PM: Registered nosave memory: 000000007c000000 - 00000000e00f8000 [ 0.000000] PM: Registered nosave memory: 00000000e00f8000 - 00000000e00f9000 [ 0.000000] PM: Registered nosave memory: 00000000e00f9000 - 00000000fed01000 [ 0.000000] PM: Registered nosave memory: 00000000fed01000 - 00000000fed02000 [ 0.000000] PM: Registered nosave memory: 00000000fed02000 - 00000000ffc00000 [ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000 [ 0.000000] e820: [mem 0x7c000000-0xe00f7fff] available for PCI devices [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88027fc00000 s80704 r8192 d21696 u524288 [ 0.000000] pcpu-alloc: s80704 r8192 d21696 u524288 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2045293 [ 0.000000] Kernel command line: root=/dev/md0 ihd_num=4 netif_num=2 HddHotplug=1 SataPortMap=23 sata_remap=0>2:1>3:2 >0:3>1 acpi_enforce_resources=lax libata.force=5:3.0G syno_hw_version=DS916+ vender_format_version=2 syno_hdd_detect=56, 59,63,57 syno_hdd_enable=61,60,71,58 syno_usb_vbus_gpio=93@0000:00:14.0@2 KPTI_on sn=1640NZN335101 macs=0011325bbf09,001 1325bbf0a [ 0.000000] Internal HD num: 4 [ 0.000000] Internal netif num: 2 [ 0.000000] Support HDD Hotplug. [ 0.000000] Sata Port Map: 23 [ 0.000000] SYNO: sata remap initialized [ 0.000000] Synology Hardware Version: DS916+-j [ 0.000000] Vender format version: 2 [ 0.000000] SYNO GPIO hdd detect pin: 56 59 63 57 [ 0.000000] SYNO GPIO hdd enable pin: 61 60 71 58 [ 0.000000] USB Vbus GPIO Control: [ 0.000000] Gpp#93 - Host:0000:00:14.0 - Port:2Serial Number: 1640NZN335101 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Memory: 8043488k/10485760k available (4744k kernel code, 2191088k absent, 251184k reserved, 4096k data, 8 04k init) [ 0.000000] x86/pti: Unmapping kernel while in userspace [ 0.000000] Kernel/User page tables isolation: enabled [ 0.000000] Hierarchical RCU implementation. [ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32 [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] NR_IRQS:4352 nr_irqs:1024 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled [ 0.000000] allocated 33554432 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.001000] tsc: Fast TSC calibration failed [ 0.003000] tsc: PIT calibration matches PMTIMER. 1 loops [ 0.004000] tsc: Detected 1599.927 MHz processor [ 0.000005] Calibrating delay loop (skipped), value calculated using timer frequency.. 3199.85 BogoMIPS (lpj=1599927) [ 0.011896] pid_max: default: 32768 minimum: 301 [ 0.017106] init_memory_mapping: [mem 0x7a4bf000-0x7a6befff] [ 0.023446] [mem 0x7a4bf000-0x7a6befff] page 4k [ 0.023469] init_memory_mapping: [mem 0x7a6bf000-0x7aabefff] [ 0.029805] [mem 0x7a6bf000-0x7a7fffff] page 4k [ 0.029809] [mem 0x7a800000-0x7a9fffff] page 2M [ 0.029811] [mem 0x7aa00000-0x7aabefff] page 4k [ 0.030795] Security Framework initialized [ 0.035400] AppArmor: AppArmor initialized [ 0.040012] Mount-cache hash table entries: 256 [ 0.045387] Initializing cgroup subsys memory [ 0.050287] Initializing cgroup subsys devices [ 0.055265] Initializing cgroup subsys freezer [ 0.060242] Initializing cgroup subsys blkio [ 0.065058] CPU: Physical Processor ID: 0 [ 0.069552] CPU: Processor Core ID: 0 [ 0.073657] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.093718] mce: CPU supports 6 MCE banks [ 0.098222] CPU0: Thermal monitoring enabled (TM1) [ 0.103593] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 Last level dTLB entries: 4KB 256, 2MB 0, 4MB 0 tlb_flushall_shift: 6 [ 0.119351] FEATURE SPEC_CTRL Not Present [ 0.123841] FEATURE IBPB_SUPPORT Not Present [ 0.128627] Spectre V2 : Vulnerable: Retpoline without IBPB [ 0.134998] Freeing SMP alternatives: 20k freed [ 0.140082] ACPI: Core revision 20130328 [ 0.156953] ACPI: All ACPI Tables successfully acquired [ 0.167995] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.184716] smpboot: CPU0: Intel(R) Pentium(R) CPU N3710 @ 1.60GHz (fam: 06, model: 4c, stepping: 04) [ 0.195279] TSC deadline timer enabled [ 0.195297] Performance Events: no PEBS fmt2+, generic architected perfmon, Intel PMU driver. [ 0.204869] ... version: 3 [ 0.209342] ... bit width: 40 [ 0.213918] ... generic registers: 2 [ 0.218399] ... value mask: 000000ffffffffff [ 0.224337] ... max period: 000000007fffffff [ 0.230273] ... fixed-purpose events: 3 [ 0.234753] ... event mask: 0000000700000003 [ 0.243584] smpboot: Booting Node 0, Processors #1 #2 #3 OK [ 0.306366] Brought up 4 CPUs [ 0.309688] smpboot: Total of 4 processors activated (12799.41 BogoMIPS) [ 0.317753] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.327165] devtmpfs: initialized [ 0.331310] PM: Registering ACPI NVS region [mem 0x0006f000-0x0006ffff] (4096 bytes) [ 0.339975] PM: Registering ACPI NVS region [mem 0x7aebf000-0x7bfbefff] (17825792 bytes) [ 0.351983] pinctrl core: initialized pinctrl subsystem [ 0.357974] NET: Registered protocol family 16 [ 0.363867] ACPI: bus type PCI registered [ 0.368586] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000) [ 0.378999] PCI: not using MMCONFIG [ 0.382898] PCI: Using configuration type 1 for base access [ 0.398077] bio: create slab at 0
[ 0.403004] ACPI: Added _OSI(Module Device)
[ 0.407689] ACPI: Added _OSI(Processor Device)
[ 0.412658] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.417909] ACPI: Added OSI(Processor Aggregator Device)
[ 0.427370] ACPI: EC: Look up EC in DSDT
[ 0.451089] ACPI: SSDT 0x000000007AEB1798 006D8 (v01 PmRef Cpu0Ist 00003000 INTL 20130117)
[ 0.461383] ACPI: Dynamic OEM Table Load:
[ 0.465885] ACPI: SSDT 0x0000000000000000 006D8 (v01 PmRef Cpu0Ist 00003000 INTL 20130117)
[ 0.475561] ACPI: SSDT 0x000000007AEB0C18 003A5 (v01 PmRef Cpu0Cst 00003001 INTL 20130117)
[ 0.485828] ACPI: Dynamic OEM Table Load:
[ 0.490331] ACPI: SSDT 0x0000000000000000 003A5 (v01 PmRef Cpu0Cst 00003001 INTL 20130117)
[ 0.505694] ACPI: SSDT 0x000000007AEB2E18 0015F (v01 PmRef ApIst 00003000 INTL 20130117)
[ 0.516018] ACPI: Dynamic OEM Table Load:
[ 0.520520] ACPI: SSDT 0x0000000000000000 0015F (v01 PmRef ApIst 00003000 INTL 20130117)
[ 0.532965] ACPI: SSDT 0x000000007AEB9E18 0008D (v01 PmRef ApCst 00003000 INTL 20130117)
[ 0.543248] ACPI: Dynamic OEM Table Load:
[ 0.547751] ACPI: SSDT 0x0000000000000000 0008D (v01 PmRef ApCst 00003000 INTL 20130117)
[ 0.563734] ACPI: Interpreter enabled
[ 0.567858] ACPI: (supports S0 S4 S5)
[ 0.571952] ACPI: Using IOAPIC for interrupt routing
[ 0.577554] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[ 0.590137] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in ACPI motherboard resources
[ 0.600097] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.610597] ACPI: No dock devices found.
[ 0.622617] ACPI: Power Resource [USBC] (on)
[ 0.635382] ACPI: Power Resource [ID3C] (off)
[ 0.651511] ACPI: Power Resource [FN00] (off)
[ 0.657616] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.664657] _SB.PCI0:_OSC invalid UUID
[ 0.664662] OSC request data:1 8 0
[ 0.664785] _SB.PCI0:_OSC invalid UUID
[ 0.664789] _OSC request data:1 1f 0
[ 0.664798] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.673751] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.683020] acpi PNP0A08:00: host bridge window expanded to [mem 0x80000000-0xdfffffff]; [mem 0x80000000-0xdfffffff] ignored
[ 0.695573] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.707432] PCI host bridge to bus 0000:00
[ 0.712018] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.718154] pci_bus 0000:00: root bus resource [io 0x0000-0x006f]
[ 0.725066] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7]
[ 0.731977] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.738888] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.746577] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[ 0.754265] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff]
[ 0.761953] pci_bus 0000:00: root bus resource [mem 0x80000000-0xdfffffff]
[ 0.769655] pci 0000:00:00.0: [8086:2280] type 00 class 0x060000
[ 0.769848] pci 0000:00:02.0: [8086:22b1] type 00 class 0x030000
[ 0.769878] pci 0000:00:02.0: reg 10: [mem 0x90000000-0x90ffffff 64bit]
[ 0.769896] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
[ 0.769908] pci 0000:00:02.0: reg 20: [io 0x4000-0x403f]
[ 0.770222] pci 0000:00:13.0: [8086:22a3] type 00 class 0x010601
[ 0.770291] pci 0000:00:13.0: reg 20: [io 0x4060-0x407f]
[ 0.770306] pci 0000:00:13.0: reg 24: [mem 0x9161b000-0x9161b7ff]
[ 0.770374] pci 0000:00:13.0: PME# supported from D3hot
[ 0.770610] pci 0000:00:14.0: [8086:22b5] type 00 class 0x0c0330
[ 0.770664] pci 0000:00:14.0: reg 10: [mem 0x91600000-0x9160ffff 64bit]
[ 0.770769] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.770896] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.777352] pci 0000:00:18.0: [8086:22c0] type 00 class 0x080102
[ 0.777381] pci 0000:00:18.0: reg 10: [mem 0x91614000-0x91617fff]
[ 0.777701] pci 0000:00:18.1: [8086:22c1] type 00 class 0x0c8000
[ 0.777730] pci 0000:00:18.1: reg 10: [mem 0x9161a000-0x9161afff]
[ 0.778055] pci 0000:00:1a.0: [8086:2298] type 00 class 0x108000
[ 0.778084] pci 0000:00:1a.0: reg 10: [mem 0x91500000-0x915fffff]
[ 0.778099] pci 0000:00:1a.0: reg 14: [mem 0x91400000-0x914fffff]
[ 0.778195] pci 0000:00:1a.0: PME# supported from D0 D3hot
[ 0.778457] pci 0000:00:1c.0: [8086:22c8] type 01 class 0x060400
[ 0.778568] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.778702] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.785154] pci 0000:00:1c.1: [8086:22ca] type 01 class 0x060400
[ 0.785265] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.785395] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.791836] pci 0000:00:1c.2: [8086:22cc] type 01 class 0x060400
[ 0.791948] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.792077] pci 0000:00:1c.2: System wakeup disabled by ACPI
[ 0.798528] pci 0000:00:1c.3: [8086:22ce] type 01 class 0x060400
[ 0.798640] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.798770] pci 0000:00:1c.3: System wakeup disabled by ACPI
[ 0.805219] pci 0000:00:1e.0: [8086:2286] type 00 class 0x080102
[ 0.805247] pci 0000:00:1e.0: reg 10: [mem 0x91610000-0x91613fff]
[ 0.805569] pci 0000:00:1e.4: [8086:228c] type 00 class 0x078000
[ 0.805598] pci 0000:00:1e.4: reg 10: [mem 0x91619000-0x91619fff]
[ 0.805916] pci 0000:00:1f.0: [8086:229c] type 00 class 0x060100
[ 0.806300] pci 0000:00:1f.3: [8086:2292] type 00 class 0x0c0500
[ 0.806361] pci 0000:00:1f.3: reg 10: [mem 0x91618000-0x9161801f]
[ 0.806479] pci 0000:00:1f.3: reg 20: [io 0x4040-0x405f]
[ 0.807022] pci 0000:01:00.0: [8086:1539] type 00 class 0x020000
[ 0.807053] pci 0000:01:00.0: reg 10: [mem 0x91300000-0x9131ffff]
[ 0.807095] pci 0000:01:00.0: reg 18: [io 0x3000-0x301f]
[ 0.807126] pci 0000:01:00.0: reg 1c: [mem 0x91320000-0x91323fff]
[ 0.807297] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.807368] pci 0000:01:00.0: System wakeup disabled by ACPI
[ 0.816729] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.822289] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.822297] pci 0000:00:1c.0: bridge window [mem 0x91300000-0x913fffff]
[ 0.822491] pci 0000:02:00.0: [8086:1539] type 00 class 0x020000
[ 0.822522] pci 0000:02:00.0: reg 10: [mem 0x91200000-0x9121ffff]
[ 0.822563] pci 0000:02:00.0: reg 18: [io 0x2000-0x201f]
[ 0.822585] pci 0000:02:00.0: reg 1c: [mem 0x91220000-0x91223fff]
[ 0.822756] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.822828] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 0.831181] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.836745] pci 0000:00:1c.1: bridge window [io 0x2000-0x2fff]
[ 0.836753] pci 0000:00:1c.1: bridge window [mem 0x91200000-0x912fffff]
[ 0.836946] pci 0000:03:00.0: [1b4b:9215] type 00 class 0x010601
[ 0.836969] pci 0000:03:00.0: reg 10: [io 0x1028-0x102f]
[ 0.836985] pci 0000:03:00.0: reg 14: [io 0x1034-0x1037]
[ 0.837000] pci 0000:03:00.0: reg 18: [io 0x1020-0x1027]
[ 0.837015] pci 0000:03:00.0: reg 1c: [io 0x1030-0x1033]
[ 0.837030] pci 0000:03:00.0: reg 20: [io 0x1000-0x101f]
[ 0.837046] pci 0000:03:00.0: reg 24: [mem 0x91100000-0x911007ff]
[ 0.837063] pci 0000:03:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
[ 0.837130] pci 0000:03:00.0: PME# supported from D3hot
[ 0.837181] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 0.845537] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.851101] pci 0000:00:1c.2: bridge window [io 0x1000-0x1fff]
[ 0.851109] pci 0000:00:1c.2: bridge window [mem 0x91100000-0x911fffff]
[ 0.851298] pci 0000:04:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 0.851335] pci 0000:04:00.0: reg 10: [mem 0x91000000-0x91007fff 64bit]
[ 0.851490] pci 0000:04:00.0: supports D1 D2
[ 0.851494] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.851549] pci 0000:04:00.0: System wakeup disabled by ACPI
[ 0.859915] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.865481] pci 0000:00:1c.3: bridge window [mem 0x91000000-0x910fffff]
[ 0.865518] pcibus 0000:00: on NUMA node 0
[ 0.867565] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.876747] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.885945] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.895128] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.904297] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.913484] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.922670] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.931848] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) 0, disabled.
[ 0.941264] cherryview-pinctrl: Adding GPIO Controller - Pin ranged 0 ~ 55
[ 0.949307] cherryview-pinctrl: Adding GPIO Controller - Pin ranged 56 ~ 114
[ 0.957517] cherryview-pinctrl: Adding GPIO Controller - Pin ranged 115 ~ 138
[ 0.965825] cherryview-pinctrl: Adding GPIO Controller - Pin ranged 139 ~ 193
[ 0.974454] ACPI: Enabled 6 GPEs in block 00 to 3F
[ 0.979843] acpi root: _SB.PCI0 notify handler is installed
[ 0.979980] Found 1 acpi root devices
[ 0.980380] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.989438] vgaarb: loaded
[ 0.992464] vgaarb: bridge control possible 0000:00:02.0
[ 0.998727] SCSI subsystem initialized
[ 1.002934] ACPI: bus type ATA registered
[ 1.007675] libata version 3.00 loaded.
[ 1.007941] pps_core: LinuxPPS API ver. 1 registered
[ 1.013494] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 1.023772] PTP clock support registered
[ 1.028417] EFI Variables Facility v0.08 2004-May-17
[ 1.051357] Registered efi as persistent store backend
[ 1.057130] PCI: Using ACPI for IRQ routing
[ 1.064386] PCI: pci_cache_line_size set to 64 bytes
[ 1.064489] e820: reserve RAM buffer [mem 0x0006f000-0x0006ffff]
[ 1.064494] e820: reserve RAM buffer [mem 0x00086000-0x0008ffff]
[ 1.064497] e820: reserve RAM buffer [mem 0x01d87330-0x03ffffff]
[ 1.064500] e820: reserve RAM buffer [mem 0x7a4bf000-0x7bffffff]
[ 1.065062] Switching to clocksource refined-jiffies
[ 1.081176] AppArmor: AppArmor Filesystem Enabled
[ 1.095515] pnp: PnP ACPI init
[ 1.098949] ACPI: bus type PNP registered
[ 1.103586] pnp 00:00: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.103742] system 00:01: [io 0x0680-0x069f] has been reserved
[ 1.110373] system 00:01: [io 0x0400-0x047f] has been reserved
[ 1.116997] system 00:01: [io 0x0500-0x05fe] has been reserved
[ 1.123619] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.123852] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.126349] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.126600] system 00:04: [mem 0xe0000000-0xefffffff] could not be reserved
[ 1.134398] system 00:04: [mem 0xfea00000-0xfeafffff] has been reserved
[ 1.141797] system 00:04: [mem 0xfed01000-0xfed01fff] has been reserved
[ 1.149196] system 00:04: [mem 0xfed03000-0xfed03fff] has been reserved
[ 1.156594] system 00:04: [mem 0xfed06000-0xfed06fff] has been reserved
[ 1.163993] system 00:04: [mem 0xfed08000-0xfed09fff] has been reserved
[ 1.171391] system 00:04: [mem 0xfed80000-0xfedbffff] could not be reserved
[ 1.179177] system 00:04: [mem 0xfed1c000-0xfed1cfff] has been reserved
[ 1.186575] system 00:04: [mem 0xfee00000-0xfeefffff] has been reserved
[ 1.193973] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.194326] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.194609] pnp: PnP ACPI: found 6 devices
[ 1.199196] ACPI: bus type PNP unregistered
[ 1.216546] Switching to clocksource acpi_pm
[ 1.221370] pci 0000:03:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[ 1.231145] pci 0000:00:1c.2: BAR 15: assigned [mem 0x91700000-0x917fffff pref]
[ 1.239348] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 1.244944] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 1.251771] pci 0000:00:1c.0: bridge window [mem 0x91300000-0x913fffff]
[ 1.259417] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 1.264987] pci 0000:00:1c.1: bridge window [io 0x2000-0x2fff]
[ 1.271820] pci 0000:00:1c.1: bridge window [mem 0x91200000-0x912fffff]
[ 1.279477] pci 0000:03:00.0: BAR 6: assigned [mem 0x91700000-0x9170ffff pref]
[ 1.287571] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 1.293147] pci 0000:00:1c.2: bridge window [io 0x1000-0x1fff]
[ 1.299970] pci 0000:00:1c.2: bridge window [mem 0x91100000-0x911fffff]
[ 1.307569] pci 0000:00:1c.2: bridge window [mem 0x91700000-0x917fffff pref]
[ 1.315667] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 1.321244] pci 0000:00:1c.3: bridge window [mem 0x91000000-0x910fffff]
[ 1.329497] pci_bus 0000:00: resource 4 [io 0x0000-0x006f]
[ 1.329503] pci_bus 0000:00: resource 5 [io 0x0078-0x0cf7]
[ 1.329508] pci_bus 0000:00: resource 6 [io 0x0d00-0xffff]
[ 1.329512] pci_bus 0000:00: resource 7 [mem 0x000a0000-0x000bffff]
[ 1.329516] pci_bus 0000:00: resource 8 [mem 0x000c0000-0x000dffff]
[ 1.329521] pci_bus 0000:00: resource 9 [mem 0x000e0000-0x000fffff]
[ 1.329525] pci_bus 0000:00: resource 10 [mem 0x80000000-0xdfffffff]
[ 1.329530] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 1.329534] pci_bus 0000:01: resource 1 [mem 0x91300000-0x913fffff]
[ 1.329539] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 1.329543] pci_bus 0000:02: resource 1 [mem 0x91200000-0x912fffff]
[ 1.329548] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 1.329552] pci_bus 0000:03: resource 1 [mem 0x91100000-0x911fffff]
[ 1.329556] pci_bus 0000:03: resource 2 [mem 0x91700000-0x917fffff pref]
[ 1.329561] pci_bus 0000:04: resource 1 [mem 0x91000000-0x910fffff]
[ 1.329780] NET: Registered protocol family 2
[ 1.335217] TCP established hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.343812] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.351808] TCP: Hash tables configured (established 65536 bind 65536)
[ 1.359211] TCP: reno registered
[ 1.362861] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 1.369764] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 1.377314] NET: Registered protocol family 1
[ 1.382227] pci 0000:00:02.0: Boot video device
[ 1.384413] pci 0000:03:00.0: Apply mv9235 specific programming steps
[ 1.391777] PCI: CLS 64 bytes, default 64
[ 1.775285] Trying to unpack rootfs image as initramfs...
[ 3.665967] decompress cpio completed and skip redundant lzma
[ 3.672774] Freeing initrd memory: 4900k freed
[ 3.679737] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 3.686986] software IO TLB [mem 0x6d27e000-0x7127e000] (64MB) mapped at [ffff88006d27e000-ffff88007127dfff]
[ 3.725653] Initialise module verification
[ 3.730438] audit: initializing netlink socket (disabled)
[ 3.736551] type=2000 audit(1641660301.200:1): initialized
[ 3.771125] bounce pool size: 64 pages
[ 3.777402] VFS: Disk quotas dquot_6.5.2
[ 3.781895] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 3.789957] msgmni has been set to 15801
[ 3.795650] Key type asymmetric registered
[ 3.800262] Asymmetric key parser 'x509' registered
[ 3.806085] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 3.814392] io scheduler noop registered
[ 3.818793] io scheduler deadline registered
[ 3.823641] io scheduler cfq registered (default)
[ 4.699349] tsc: Refined TSC clocksource calibration: 1599.947 MHz
[ 4.706337] Switching to clocksource tsc
[ 5.032741] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.062047] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 5.072854] 0000:00:1e.4: ttyS1 at MMIO 0x91619000 (irq = 19) is a 16550A
[ 5.191664] brd: module loaded
[ 5.201425] Loading iSCSI transport class v2.0-870.
[ 5.240375] ahci 0000:00:13.0: version 3.0
[ 5.240649] ahci 0000:00:13.0: irq 131 for MSI/MSI-X
[ 5.240750] ahci 0000:00:13.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 5.249827] ahci 0000:00:13.0: flags: 64bit ncq led clo only pio slum part deso sadm sds apst
[ 5.259483] ahci 0000:00:13.0: setting latency timer to 64
[ 5.268326] scsi0 : ahci
[ 5.272635] scsi1 : ahci
[ 5.276549] ata1: SATA max UDMA/133 abar m2048@0x9161b000 port 0x9161b100 irq 131
[ 5.284963] ata2: SATA max UDMA/133 abar m2048@0x9161b000 port 0x9161b180 irq 131
[ 13.656961] ata1: link is slow to respond, please be patient (ready=0)
[ 17.488845] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 17.685650] ata1.00: ATA-9: WDC WD40EFRX-68WT0N0, 80.00A80, max UDMA/133
[ 17.693152] ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 17.701133] ata1.00: SN: WD-WCC4E0211824
[ 17.706540] ata1.00: configured for UDMA/133
[ 17.712011] scsi 0:0:0:0: Direct-Access WDC WD40EFRX-68WT0N0 80.0 PQ: 0 ANSI: 5
[ 17.722728] sd 0:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 17.731409] sd 0:0:0:0: [sdc] 4096-byte physical blocks
[ 17.731802] Delay 5 seconds to wait for disk 4 ready.
[ 17.743061] sd 0:0:0:0: [sdc] Write Protect is off
[ 17.748433] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 17.748492] sd 0:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.814493] sdc: sdc1 sdc2 sdc3
[ 17.820701] sd 0:0:0:0: [sdc] Attached SCSI disk
[ 31.095385] ata2: link is slow to respond, please be patient (ready=0)
[ 34.723275] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 34.928650] ata2.00: ATA-9: WDC WD40EFRX-68WT0N0, 80.00A80, max UDMA/133
[ 34.936174] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 34.944153] ata2.00: SN: WD-WCC4E0296239
[ 34.949569] ata2.00: configured for UDMA/133
[ 34.955034] scsi 1:0:0:0: Direct-Access WDC WD40EFRX-68WT0N0 80.0 PQ: 0 ANSI: 5
[ 34.965793] sd 1:0:0:0: [sdd] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 34.969309] ahci 0000:03:00.0: irq 132 for MSI/MSI-X
[ 34.969396] Change defer qc mode on external port for compatibility
[ 34.969397] Change defer qc mode on external port for compatibility
[ 34.969398] Change defer qc mode on external port for compatibility
[ 34.980320] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[ 34.980326] ahci 0000:03:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 35.005924] scsi2 : ahci
[ 35.008595] scsi3 : ahci
[ 35.010853] scsi4 : ahci
[ 35.014581] ata3: SATA max UDMA/133 abar m2048@0x91100000 port 0x91100100 irq 132
[ 35.014586] ata4: SATA max UDMA/133 abar m2048@0x91100000 port 0x91100180 irq 132
[ 35.014589] ata5: FORCE: PHY spd limit set to 3.0Gbps
[ 35.014591] ata5: SATA max UDMA/133 abar m2048@0x91100000 port 0x91100200 irq 132
[ 35.014602] Delay 5 seconds to wait for disk 1 ready.
[ 35.058471] sd 1:0:0:0: [sdd] 4096-byte physical blocks
[ 35.064524] sd 1:0:0:0: [sdd] Write Protect is off
[ 35.069895] sd 1:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 35.069977] sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.143717] sdd: sdd1 sdd2 sdd3
[ 35.150126] sd 1:0:0:0: [sdd] Attached SCSI disk
[ 48.377815] ata3: link is slow to respond, please be patient (ready=0)
[ 52.517684] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 52.525218] ata3.00: ATA-9: WDC WD40EFRX-68WT0N0, 80.00A80, max UDMA/133
[ 52.532723] ata3.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 52.540704] ata3.00: SN: WD-WCC4E0297045
[ 52.546127] ata3.00: configured for UDMA/133
[ 52.551602] scsi 2:0:0:0: Direct-Access WDC WD40EFRX-68WT0N0 80.0 PQ: 0 ANSI: 5
[ 52.562371] sd 2:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 52.571056] sd 2:0:0:0: [sda] 4096-byte physical blocks
[ 52.572304] Delay 5 seconds to wait for disk 2 ready.
[ 52.582720] sd 2:0:0:0: [sda] Write Protect is off
[ 52.588078] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 52.588136] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 52.662647] sda: sda1 sda2 sda3
[ 52.668846] sd 2:0:0:0: [sda] Attached SCSI disk
[ 65.936232] ata4: link is slow to respond, please be patient (ready=0)
[ 69.974108] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 69.981643] ata4.00: ATA-9: WDC WD40EFRX-68WT0N0, 80.00A80, max UDMA/133
[ 69.989142] ata4.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 69.997123] ata4.00: SN: WD-WCC4E0294163
[ 70.002546] ata4.00: configured for UDMA/133
[ 70.008030] scsi 3:0:0:0: Direct-Access WDC WD40EFRX-68WT0N0 80.0 PQ: 0 ANSI: 5
[ 70.018817] sd 3:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 70.027500] sd 3:0:0:0: [sdb] 4096-byte physical blocks
[ 70.033555] sd 3:0:0:0: [sdb] Write Protect is off
[ 70.038966] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.039063] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.115844] sdb: sdb1 sdb2 sdb3
[ 70.120865] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 75.374920] ata5: link is slow to respond, please be patient (ready=0)
[ 80.175773] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 83.213228] ata5: PMP Power control set ATA_EH_SYNO_PWON
[ 85.249669] ata5.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 5 ports, feat 0x1/0x9
[ 85.315728] ahci 0000:03:00.0: FBS is enabled
[ 85.320735] ata5.00: FORCE: PHY spd limit set to 3.0Gbps
[ 85.326754] ata5.01: FORCE: PHY spd limit set to 3.0Gbps
[ 85.332789] ata5.02: FORCE: PHY spd limit set to 3.0Gbps
[ 85.338856] ata5.03: FORCE: PHY spd limit set to 3.0Gbps
[ 85.344842] ata5.04: FORCE: PHY spd limit set to 3.0Gbps
[ 89.635459] ata5.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 90.673389] ata5: Apply Synology fast PMP boot
[ 94.203544] ata5.00: hard resetting link
[ 94.512439] ahci 0000:03:00.0: FBS is disabled
[ 94.672283] ahci 0000:03:00.0: FBS is enabled
[ 94.677361] ata5.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 94.684718] ata5.01: hard resetting link
[ 94.994421] ahci 0000:03:00.0: FBS is disabled
[ 95.154265] ahci 0000:03:00.0: FBS is enabled
[ 95.159343] ata5.01: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 95.166695] ata5.02: hard resetting link
[ 95.476406] ahci 0000:03:00.0: FBS is disabled
[ 95.636251] ahci 0000:03:00.0: FBS is enabled
[ 95.641329] ata5.02: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 95.648682] ata5.03: hard resetting link
[ 95.958388] ahci 0000:03:00.0: FBS is disabled
[ 96.118235] ahci 0000:03:00.0: FBS is enabled
[ 96.123303] ata5.03: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 96.130658] ata5.04: hard resetting link
[ 96.440374] ahci 0000:03:00.0: FBS is disabled
[ 96.600218] ahci 0000:03:00.0: FBS is enabled
[ 96.605295] ata5.04: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 96.613182] ata5.00: ATA-10: WDC WD40EFRX-68N32N0, 82.00A82, max UDMA/133
[ 96.620782] ata5.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 96.628364] ata5.00: SN: WD-WCC7K2HRATD5
[ 96.633735] ata5.00: configured for UDMA/133
[ 96.639008] ata5.01: ATA-10: WDC WD40EFAX-68JH4N1, 83.00A83, max UDMA/133
[ 96.646605] ata5.01: 7814037168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 96.654196] ata5.01: SN: WD-WX42D80NRDJK
[ 96.659475] ata5.01: configured for UDMA/133
[ 96.664800] ata5.02: ATA-9: WDC WD40EFRX-68WT0N0, 82.00A82, max UDMA/133
[ 96.672302] ata5.02: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 96.679804] ata5.02: SN: WD-WCC4E0EJ528C
[ 96.685181] ata5.02: configured for UDMA/133
[ 96.690503] ata5.03: ATA-9: WDC WD40EFRX-68WT0N0, 82.00A82, max UDMA/133
[ 96.698004] ata5.03: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 96.705506] ata5.03: SN: WD-WCC4E4JP2NP0
[ 96.710887] ata5.03: configured for UDMA/133
[ 96.715850] ata5.04: ATA-8: PLEXTOR PX-256M3, 1.07, max UDMA/133
[ 96.722574] ata5.04: 500118192 sectors, multi 1: LBA48 NCQ (depth 0/32)
[ 96.729970] ata5.04: SN:002146102308
[ 96.734210] ata5.04: configured for UDMA/133
[ 96.739061] ata5: EH complete
[ 96.760235] scsi 4:15:0:0: Processor Synology Virtual Device 1.00 PQ: 0 ANSI: 4
[ 96.770165] blk_limits_max_hw_sectors: set to minimum 8
[ 96.777716] scsi 4:0:0:0: Direct-Access WDC WD40EFRX-68N32N0 82.0 PQ: 0 ANSI: 5
[ 96.788414] sd 4:0:0:0: [sdea] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 96.791830] scsi 4:1:0:0: Direct-Access WDC WD40EFAX-68JH4N1 83.0 PQ: 0 ANSI: 5
[ 96.798573] sd 4:1:0:0: [sdeb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 96.798577] sd 4:1:0:0: [sdeb] 4096-byte physical blocks
[ 96.798746] sd 4:1:0:0: [sdeb] Write Protect is off
[ 96.798750] sd 4:1:0:0: [sdeb] Mode Sense: 00 3a 00 00
[ 96.798804] sd 4:1:0:0: [sdeb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 96.837441] sd 4:0:0:0: [sdea] 4096-byte physical blocks
[ 96.837924] scsi 4:2:0:0: Direct-Access WDC WD40EFRX-68WT0N0 82.0 PQ: 0 ANSI: 5
[ 96.838726] sd 4:2:0:0: [sdec] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 96.838729] sd 4:2:0:0: [sdec] 4096-byte physical blocks
[ 96.838851] sd 4:2:0:0: [sdec] Write Protect is off
[ 96.838855] sd 4:2:0:0: [sdec] Mode Sense: 00 3a 00 00
[ 96.838908] sd 4:2:0:0: [sdec] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 96.864905] scsi 4:3:0:0: Direct-Access WDC WD40EFRX-68WT0N0 82.0 PQ: 0 ANSI: 5
[ 96.865726] sd 4:3:0:0: [sded] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 96.865729] sd 4:3:0:0: [sded] 4096-byte physical blocks
[ 96.865849] sd 4:3:0:0: [sded] Write Protect is off
[ 96.865853] sd 4:3:0:0: [sded] Mode Sense: 00 3a 00 00
[ 96.865907] sd 4:3:0:0: [sded] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 96.868421] sdeb: sdeb1 sdeb2 sdeb3
[ 96.871081] ata5.04: Find SSD disks. [PLEXTOR PX-256M3]
[ 96.925864] scsi 4:4:0:0: Direct-Access PLEXTOR PX-256M3 1.07 PQ: 0 ANSI: 5
[ 96.926136] sd 4:1:0:0: [sdeb] Attached SCSI disk
[ 96.928082] sd 4:4:0:0: [sdee] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 96.928085] sd 4:4:0:0: [sdee] 4096-byte physical blocks
[ 96.928288] sd 4:4:0:0: [sdee] Write Protect is off
[ 96.928292] sd 4:4:0:0: [sdee] Mode Sense: 00 3a 00 00
[ 96.928345] sd 4:4:0:0: [sdee] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 96.963413] sdee: sdee1
[ 96.964073] sdec: sdec1 sdec2 sdec3
[ 96.964740] rtc_cmos 00:05: RTC can wake from S4
[ 96.969296] sded: sded1 sded2 sded3
[ 96.976009] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 96.976066] rtccmos 00:05: alarms up to one month, y3k, 242 bytes nvram
[ 96.980512] sd 4:4:0:0: [sdee] Attached SCSI disk
[ 96.994802] i2c /dev entries driver
[ 97.015649] ACPI Warning: 0x0000000000004040-0x000000000000405F SystemIO conflicts with Region _SB.PCI0.SBUS.SMBI 1 (20130328/utaddress-249)
[ 97.015651] ACPI: This conflict may cause random problems and system instability
[ 97.015652] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 97.037434] sd 4:2:0:0: [sdec] Attached SCSI disk
[ 97.050617] sd 4:3:0:0: [sded] Attached SCSI disk
[ 97.063152] sd 4:0:0:0: [sdea] Write Protect is off
[ 97.068680] sd 4:0:0:0: [sdea] Mode Sense: 00 3a 00 00
[ 97.071016] sd 4:0:0:0: [sdea] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 97.091069] md: raid1 personality registered for level 1
[ 97.097064] cpuidle: using governor ladder
[ 97.101685] cpuidle: using governor menu
[ 97.106302] TCP: cubic registered
[ 97.110031] NET: Registered protocol family 17
[ 97.115038] Key type dns_resolver registered
[ 97.130235] sdea: sdea1 sdea2 sdea3
[ 97.142763] sd 4:0:0:0: [sdea] Attached SCSI disk
[ 97.148852] Loading module verification blacklist certificates
[ 97.155426] Loading module verification certificates
[ 97.161049] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329'
[ 97.175138] MODSIGN: Loaded cert 'Synology Root Certification Authority: '
[ 97.186768] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: '
[ 97.200023] MODSIGN: Loaded cert 'Synology kernel module signing key: '
[ 97.211349] registered taskstats version 1
[ 97.216683] rtc_cmos 00:05: setting system clock to 2022-01-08 16:46:36 UTC (1641660396)
[ 97.227731] Freeing unused kernel memory: 804k freed
[ 97.233561] Write protecting the kernel read-only data: 8192k
[ 97.240284] Freeing unused kernel memory: 1388k freed
[ 97.248981] Freeing unused kernel memory: 552k freed
[ 97.401274] ACPI: bus type USB registered
[ 97.407472] usbcore: registered new interface driver usbfs
[ 97.413888] usbcore: registered new interface driver hub
[ 97.420214] usbcore: registered new interface driver ethub
[ 97.426675] usbcore: registered new device driver usb
[ 97.466310] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 97.466323] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 97.472207] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 97.680636] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 97.680678] xhci_hcd 0000:00:14.0: irq 133 for MSI/MSI-X
[ 97.681188] xHCI xhci_add_endpoint called for root hub
[ 97.681194] xHCI xhci_check_bandwidth called for root hub
[ 97.681441] hub 1-0:1.0: USB hub found
[ 97.685668] hub 1-0:1.0: 7 ports detected
[ 97.691362] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 97.697231] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 97.705973] xHCI xhci_add_endpoint called for root hub
[ 97.705980] xHCI xhci_check_bandwidth called for root hub
[ 97.706227] hub 2-0:1.0: USB hub found
[ 97.710455] hub 2-0:1.0: 6 ports detected
[ 97.755758] etxhci_hcd-170202 0000:04:00.0: Etron xHCI Host Controller
[ 97.763080] etxhci_hcd-170202 0000:04:00.0: new USB bus registered, assigned bus number 3
[ 97.784595] etxhci_hcd-170202 0000:04:00.0: irq 134 for MSI/MSI-X
[ 97.785541] xHCI etxhci_add_endpoint called for root hub
[ 97.785545] xHCI etxhci_check_bandwidth called for root hub
[ 97.785796] ethub 3-0:1.0: USB hub found
[ 97.790225] ethub 3-0:1.0: 2 ports detected
[ 97.795061] etxhci_hcd-170202 0000:04:00.0: Etron xHCI Host Controller
[ 97.802379] etxhci_hcd-170202 0000:04:00.0: new USB bus registered, assigned bus number 4
[ 97.813230] xHCI etxhci_add_endpoint called for root hub
[ 97.813239] xHCI etxhci_check_bandwidth called for root hub
[ 97.813536] ethub 4-0:1.0: USB hub found
[ 97.817961] ethub 4-0:1.0: 2 ports detected
[ 97.832378] braswell_synobios: module license 'Synology Inc.' taints kernel.
[ 97.840272] Disabling lock debugging due to kernel taint
[ 97.847047] synobios open /dev/ttyS1 success
[ 97.851973] 2022-1-8 16:46:37 UTC
[ 97.855689] synobios: load, major number 201
[ 97.860471] Brand: Synology
[ 97.863595] Model: DS-916+
[ 97.866622] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 97.876083] synobios cpu_arch proc entry initialized
[ 97.881637] synobios crypto_hw proc entry initialized
[ 97.887289] synobios syno_platform proc entry initialized
[ 97.905386] Module [braswell_synobios] is removed.
[ 97.910913] synobios: unload
[ 98.084040] md: md0 stopped.
[ 98.091474] md: bind
[ 98.094848] md: bind
[ 98.098182] md: bind
[ 98.101541] md: bind
[ 98.105027] md/raid1:md0: active with 4 out of 4 mirrors
[ 98.133890] md0: detected capacity change from 0 to 2549940224
[ 98.141028] md0: unknown partition table
[ 99.017151] usb 1-5: new high-speed USB device number 2 using xhci_hcd
[ 99.148143] usb 3-2: new full-speed USB device number 2 using etxhci_hcd-170202
[ 99.824914] usb 3-2: ep 0x81 - rounding interval to 128 microframes, ep desc says 160 microframes
[ 100.938327] usb 4-1: new SuperSpeed USB device number 2 using etxhci_hcd-170202
[ 101.156141] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (2c0)
[ 101.167370] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (2c0)
[ 101.194323] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
[ 106.899194] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (2c0)
[ 106.909136] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (2c0)
[ 106.933892] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
[ 107.271653] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (2c0)
[ 107.300063] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: barrier=1
[ 107.911098] systemd[1]: systemd 219 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UT MP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
[ 107.931590] systemd[1]: Detected architecture x86-64.
[ 107.949187] systemd[1]: Set hostname to .
[ 111.008621] systemd[1]: Cannot add dependency job for unit pkg-install-low-priority-builtin.service, ignoring: Unit p kg-install-low-priority-builtin.service failed to load: No such file or directory.
[ 111.028493] systemd[1]: Cannot add dependency job for unit pkgctl-mc.service, ignoring: Unit pkgctl-mc.service failed to load: No such file or directory.
[ 111.043915] systemd[1]: Cannot add dependency job for unit pkgctl-SynologyMoments.service, ignoring: Unit pkgctl-Syno logyMoments.service failed to load: No such file or directory.
[ 111.061840] systemd[1]: Cannot add dependency job for unit pkgctl-nano.service, ignoring: Unit pkgctl-nano.service fa iled to load: No such file or directory.
[ 111.077675] systemd[1]: Cannot add dependency job for unit pkg-install-high-priority-builtin.service, ignoring: Unit pkg-install-high-priority-builtin.service failed to load: No such file or directory.
[ 111.101689] systemd[1]: Reached target Timers.
[ 111.108226] systemd[1]: Starting Timers.
[ 111.114180] systemd[1]: Reached target Swap.
[ 111.119868] systemd[1]: Starting Swap.
[ 111.126183] systemd[1]: Created slice Root Slice.
[ 111.132436] systemd[1]: Starting Root Slice.
[ 111.139034] systemd[1]: Created slice SynologyPhotos's slice.
[ 111.146752] systemd[1]: Starting SynologyPhotos's slice.
[ 111.154474] systemd[1]: Created slice Synology DSM desktop service.
[ 111.162792] systemd[1]: Starting Synology DSM desktop service.
[ 111.171086] systemd[1]: Created slice HyperBackup's slice.
[ 111.178543] systemd[1]: Starting HyperBackup's slice.
[ 111.185941] systemd[1]: Created slice r8152's slice.
[ 111.192843] systemd[1]: Starting r8152's slice.
[ 111.199657] systemd[1]: Created slice SNMP.
[ 111.205687] systemd[1]: Starting SNMP.
[ 111.211673] systemd[1]: Created slice Synology Flashcache.
[ 111.219115] systemd[1]: Starting Synology Flashcache.
[ 111.226511] systemd[1]: Created slice Synology Swap Works.
[ 111.233996] systemd[1]: Starting Synology Swap Works.
[ 111.241425] systemd[1]: Created slice SSDP service.
[ 111.248241] systemd[1]: Starting SSDP service.
[ 111.254938] systemd[1]: Created slice RAID Resync Process. Including Resync, Repair and Reshape..
[ 111.266223] systemd[1]: Starting RAID Resync Process. Including Resync, Repair and Reshape..
[ 111.277385] systemd[1]: Created slice Perl's slice.
[ 111.284198] systemd[1]: Starting Perl's slice.
[ 111.290914] systemd[1]: Created slice Node.js_v12's slice.
[ 111.298428] systemd[1]: Starting Node.js_v12's slice.
[ 111.305860] systemd[1]: Created slice ScsiTarget's slice.
[ 111.313181] systemd[1]: Starting ScsiTarget's slice.
[ 111.320477] systemd[1]: Created slice synobackup daemon slice.
[ 111.328356] systemd[1]: Starting synobackup daemon slice.
[ 111.336149] systemd[1]: Created slice Synology DSM internal service.
[ 111.344602] systemd[1]: Starting Synology DSM internal service.
[ 111.352972] systemd[1]: Created slice QuickConnect synorelayd group.
[ 111.361426] systemd[1]: Starting QuickConnect synorelayd group.
[ 111.369806] systemd[1]: Created slice AudioStation's slice.
[ 111.377380] systemd[1]: Starting AudioStation's slice.
[ 111.384890] systemd[1]: Created slice synocli-file's slice.
[ 111.392458] systemd[1]: Starting synocli-file's slice.
[ 111.399954] systemd[1]: Created slice OpenBSD Secure Shell server.
[ 111.408218] systemd[1]: Starting OpenBSD Secure Shell server.
[ 111.416397] systemd[1]: Created slice scemd.
[ 111.422517] systemd[1]: Starting scemd.
[ 111.428568] systemd[1]: Created slice DownloadStation's slice.
[ 111.436424] systemd[1]: Starting DownloadStation's slice.
[ 111.444214] systemd[1]: Created slice AntiVirus's slice.
[ 111.451499] systemd[1]: Starting AntiVirus's slice.
[ 111.458732] systemd[1]: Created slice Synology Cache Advisor.
[ 111.466498] systemd[1]: Starting Synology Cache Advisor.
[ 111.474178] systemd[1]: Created slice dsm6-ui-compatible's slice.
[ 111.482339] systemd[1]: Starting dsm6-ui-compatible's slice.
[ 111.490465] systemd[1]: Created slice BTRFS Space Reclaim.
[ 111.497904] systemd[1]: Starting BTRFS Space Reclaim.
[ 111.505365] systemd[1]: Created slice System Slice.
[ 111.512141] systemd[1]: Starting System Slice.
[ 111.518987] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 111.527280] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 111.535569] systemd[1]: Created slice system-syno\x2dmd\x2dresync\x2dspeed\x2dadjust.slice.
[ 111.546192] systemd[1]: Starting system-syno\x2dmd\x2dresync\x2dspeed\x2dadjust.slice.
[ 111.556792] systemd[1]: Created slice SynologyDrive's slice.
[ 111.564450] systemd[1]: Starting SynologyDrive's slice.
[ 111.572040] systemd[1]: Created slice SynologyApplicationService's slice.
[ 111.580984] systemd[1]: Starting SynologyApplicationService's slice.
[ 111.589848] systemd[1]: Created slice CodecPack's slice.
[ 111.597131] systemd[1]: Starting CodecPack's slice.
[ 111.604329] systemd[1]: Created slice OAuthService's slice.
[ 111.611918] systemd[1]: Starting OAuthService's slice.
[ 111.619415] systemd[1]: Created slice synocli-net's slice.
[ 111.626900] systemd[1]: Starting synocli-net's slice.
[ 111.634294] systemd[1]: Created slice VideoStation's slice.
[ 111.641876] systemd[1]: Starting VideoStation's slice.
[ 111.649376] systemd[1]: Created slice FileStation's slice.
[ 111.656853] systemd[1]: Starting FileStation's slice.
[ 111.664259] systemd[1]: Created slice Package Center Slice.
[ 111.671837] systemd[1]: Starting Package Center Slice.
[ 111.679349] systemd[1]: Created slice ReplicationService's slice.
[ 111.687504] systemd[1]: Starting ReplicationService's slice.
[ 111.695577] systemd[1]: Created slice Shared Folder Sync.
[ 111.703004] systemd[1]: Starting Shared Folder Sync.
[ 111.710200] systemd[1]: Listening on udev Kernel Socket.
[ 111.717593] systemd[1]: Starting udev Kernel Socket.
[ 111.724775] systemd[1]: Listening on udev Control Socket.
[ 111.732268] systemd[1]: Starting udev Control Socket.
[ 111.739662] systemd[1]: Created slice exFAT-Free's slice.
[ 111.747042] systemd[1]: Starting exFAT-Free's slice.
[ 111.754339] systemd[1]: Created slice Task Scheduler Group.
[ 111.761924] systemd[1]: Starting Task Scheduler Group.
[ 111.769418] systemd[1]: Created slice Performance alarm.
[ 111.776712] systemd[1]: Starting Performance alarm.
[ 111.783953] systemd[1]: Created slice User and Session Slice.
[ 111.791687] systemd[1]: Starting User and Session Slice.
[ 111.799397] systemd[1]: Created slice user-196791.slice.
[ 111.806664] systemd[1]: Starting user-196791.slice.
[ 111.813887] systemd[1]: Created slice Synology DSM Storage Service.
[ 111.822226] systemd[1]: Starting Synology DSM Storage Service.
[ 111.830346] systemd[1]: Reached target Slices.
[ 111.836820] systemd[1]: Starting Slices.
[ 111.842973] systemd[1]: Created slice SMBService's slice.
[ 111.850339] systemd[1]: Starting SMBService's slice.
[ 111.857667] systemd[1]: Created slice Python2's slice.
[ 111.864741] systemd[1]: Starting Python2's slice.
[ 111.871777] systemd[1]: Created slice Synology Index slice (WAT).
[ 111.879909] systemd[1]: Starting Synology Index slice (WAT).
[ 111.887891] systemd[1]: Listening on Journal Audit Socket.
[ 111.895691] systemd[1]: Created slice BTRFS Optimization.
[ 111.903054] systemd[1]: Starting BTRFS Optimization.
[ 111.910424] systemd[1]: Created slice HybridShare's slice.
[ 111.917840] systemd[1]: Starting HybridShare's slice.
[ 111.925250] systemd[1]: Created slice SynoFinder's slice.
[ 111.932626] systemd[1]: Starting SynoFinder's slice.
[ 111.939946] systemd[1]: Created slice ActiveInsight's slice.
[ 111.947648] systemd[1]: Starting ActiveInsight's slice.
[ 111.955240] systemd[1]: Listening on Journal Socket.
[ 111.962182] systemd[1]: Starting Journal Socket.
[ 111.970236] systemd[1]: Starting Synology Task Scheduler Init...
[ 111.978686] systemd[1]: Started Machine Check Exception Logging Daemon.
[ 111.987725] systemd[1]: Starting Machine Check Exception Logging Daemon...
[ 112.009449] systemd[1]: Mounting Temporary Directory...
[ 112.029456] systemd[1]: Starting Load Kernel Modules...
[ 112.038451] systemd[1]: Starting Link coredump path to volume if possible...
[ 112.049161] systemd[1]: Starting Synology swap...
[ 112.057504] systemd[1]: Starting Disabling fan checking flag ......
[ 112.067845] systemd[1]: Mounting Debug File System...
[ 112.076807] systemd[1]: Starting unbind USB device...
[ 112.085073] systemd[1]: Starting Load ntb_brd module...
[ 112.094112] systemd[1]: Starting Set hostname...
[ 112.102457] systemd[1]: Starting check integrity of rd.gz decompression...
[ 112.113424] systemd[1]: Starting Set boot sequence config...
[ 112.122655] systemd[1]: Starting Set time zone information to kernel...
[ 112.133119] systemd[1]: Starting Journal Socket (/dev/log).
[ 112.141290] systemd[1]: Created slice MediaServer's slice.
[ 112.148629] systemd[1]: Starting MediaServer's slice.
[ 112.156080] systemd[1]: Created slice SecureSignIn's slice.
[ 112.163581] systemd[1]: Starting SecureSignIn's slice.
[ 112.170983] systemd[1]: Reached target Paths.
[ 112.175297] ACPI: Requesting acpi_cpufreq
[ 112.178173] Monitor-Mwait will be used to enter C-1 state
[ 112.183635] systemd[1]: Starting Paths.
[ 112.190878] systemd[1]: Mounted Debug File System.
[ 112.197835] systemd[1]: Mounted Temporary Directory.
[ 112.205624] systemd[1]: Started Disabling fan checking flag ....
[ 112.213734] systemd[1]: Started unbind USB device.
[ 112.220444] systemd[1]: Started Synology Task Scheduler Init.
[ 112.228669] systemd[1]: Started Load ntb_brd module.
[ 112.235526] systemd[1]: Started Set hostname.
[ 112.242413] systemd[1]: Started Set boot sequence config.
[ 112.250195] systemd[1]: Started check integrity of rd.gz decompression.
[ 112.258566] systemd[1]: Started Set time zone information to kernel.
[ 112.267145] systemd[1]: Listening on Journal Socket (/dev/log).
[ 112.276421] systemd[1]: Starting Journal Service...
[ 112.283541] systemd[1]: Reached target Sockets.
[ 112.290001] systemd[1]: Starting Sockets.
[ 112.296106] systemd[1]: Reached target Local File Systems.
[ 112.303824] systemd[1]: Starting Local File Systems.
[ 112.312347] systemd[1]: Starting Set boot sequence config for temporary use...
[ 112.323612] systemd[1]: Starting udev Coldplug all Devices...
[ 112.332938] systemd[1]: Starting D-Bus Session Message Bus...
[ 112.342371] systemd[1]: Starting D-Bus System Message Bus...
[ 112.350530] systemd[1]: Starting Mount usb fs...
[ 112.359608] systemd-journald[4934]: Failed to join audit multicast group. The kernel is probably too old or multicast reading is not supported. Ignoring: Operation not permitted
[ 112.378110] systemd[1]: Started Set boot sequence config for temporary use.
[ 112.387547] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[ 112.423207] flashcache: flashcache-1.0-2021-09-24-03:30 initialized
[ 112.455111] systemd[1]: Started Journal Service.
[ 112.455527] flashcache_syno: flashcache-1.0-syno-v25-pin-file-2021-09-24-03:30-debug initialized
[ 112.505526] NET: Registered protocol family 10
[ 112.527667] systemd-journald[4934]: Received request to flush runtime journal from PID 1
[ 112.545598] sit: IPv6 over IPv4 tunneling driver
[ 112.753485] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 112.759526] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 112.765615] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 112.771684] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 112.777764] scsi 4:15:0:0: Attached scsi generic sg4 type 3
[ 112.778712] zram: module is from the staging directory, the quality is unknown, you have been warned.
[ 112.779779] zram: Created 4 device(s) ...
[ 112.798984] sd 4:0:0:0: Attached scsi generic sg5 type 0
[ 112.805747] sd 4:1:0:0: Attached scsi generic sg6 type 0
[ 112.811860] sd 4:2:0:0: Attached scsi generic sg7 type 0
[ 112.817992] sd 4:3:0:0: Attached scsi generic sg8 type 0
[ 112.825605] sd 4:4:0:0: Attached scsi generic sg9 type 0
[ 112.873333] e1000e: Intel(R) PRO/1000 Network Driver - 3.4.2.4-NAPI
[ 112.881595] e1000e: Copyright(c) 1999 - 2019 Intel Corporation.
[ 112.938958] Intel(R) Gigabit Ethernet Linux Driver - version 5.3.5.22
[ 112.946193] Copyright(c) 2007 - 2018 Intel Corporation.
[ 112.952728] igb 0000:01:00.0: irq 135 for MSI/MSI-X
[ 112.952746] igb 0000:01:00.0: irq 136 for MSI/MSI-X
[ 112.994729] igb 0000:01:00.0: added PHC on eth0
[ 112.999828] igb 0000:01:00.0: Intel(R) Gigabit Ethernet Linux Driver
[ 113.006992] igb 0000:01:00.0: eth0: (PCIe:2.5GT/s:Width x1)
[ 113.013335] igb 0000:01:00.0 eth0: MAC: 12:34:56:78:9a:bc
[ 113.019385] igb 0000:01:00.0: eth0: PBA No: Unknown
[ 113.024862] igb 0000:01:00.0: LRO is disabled
[ 113.029741] igb 0000:01:00.0: Using MSI-X interrupts. 1 rx queue(s), 1 tx queue(s)
[ 113.038837] igb 0000:02:00.0: irq 137 for MSI/MSI-X
[ 113.038854] igb 0000:02:00.0: irq 138 for MSI/MSI-X
[ 113.080641] igb 0000:02:00.0: added PHC on eth1
[ 113.085719] igb 0000:02:00.0: Intel(R) Gigabit Ethernet Linux Driver
[ 113.092884] igb 0000:02:00.0: eth1: (PCIe:2.5GT/s:Width x1)
[ 113.099241] igb 0000:02:00.0 eth1: MAC: 12:34:56:78:9a:bc
[ 113.105336] igb 0000:02:00.0: eth1: PBA No: Unknown
[ 113.109564] md: md1 stopped.
[ 113.114076] igb 0000:02:00.0: LRO is disabled
[ 113.118964] igb 0000:02:00.0: Using MSI-X interrupts. 1 rx queue(s), 1 tx queue(s)
[ 113.179838] usb-storage 1-5:1.0: USB Mass Storage device detected
[ 113.186838] scsi5 : usb-storage 1-5:1.0
[ 113.191332] usbcore: registered new interface driver usb-storage
[ 113.191695] md: bind
[ 113.201133] md: bind
[ 113.201318] md: bind
[ 113.202999] md: bind
[ 113.207376] md/raid1:md1: active with 4 out of 4 mirrors
[ 113.249658] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 113.271191] md1: detected capacity change from 0 to 2147418112
[ 113.278914] ehci-pci: EHCI PCI platform driver
[ 113.291866] uhci_hcd: USB Universal Host Controller Interface driver
[ 113.300316] md1: unknown partition table
[ 113.304098] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 113.304104] ACPI: Power Button [PWR2]
[ 113.304188] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[ 113.304192] ACPI: Sleep Button [SLPB]
[ 113.304264] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 113.304268] ACPI: Power Button [PWRF]
[ 113.316500] Linux agpgart interface v0.103
[ 113.380123] [drm] Initialized drm 1.1.0 20060810
[ 113.563843] [drm] Memory usable by graphics device = 2048M
[ 113.570015] i915 0000:00:02.0: setting latency timer to 64
[ 113.570518] mtrr: no more MTRRs available
[ 113.575049] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 113.583481] i915 0000:00:02.0: irq 139 for MSI/MSI-X
[ 113.583503] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 113.590947] [drm] Driver supports precise vblank timestamp query.
[ 113.633764] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 113.719118] acpi device:28: registered as cooling_device4
[ 113.725224] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 113.732995] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input3
[ 113.743088] [drm] Initialized i915 1.6.0 20141121 for 0000:00:02.0 on minor 0
[ 113.788642] [drm] GMBUS [i915 gmbus panel] timed out, falling back to bit banging on pin 3
[ 113.820647] i915 0000:00:02.0: No connectors reported connected with modes
[ 113.828366] [drm] Cannot find any crtc or sizes - going 1024x768
[ 114.183684] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 114.190634] i915 0000:00:02.0: registered panic notifier
[ 114.198777] scsi 5:0:0:0: Direct-Access Synology DiskStation PMAP PQ: 0 ANSI: 6
[ 114.209342] sd 5:0:0:0: Attached scsi generic sg10 type 0
[ 114.217279] sd 5:0:0:0: [synoboot] 245760 512-byte logical blocks: (125 MB/120 MiB)
[ 114.227812] sd 5:0:0:0: [synoboot] Write Protect is off
[ 114.234075] sd 5:0:0:0: [synoboot] Mode Sense: 23 00 00 00
[ 114.235141] sd 5:0:0:0: [synoboot] No Caching mode page found
[ 114.242076] sd 5:0:0:0: [synoboot] Assuming drive cache: write through
[ 114.253210] sd 5:0:0:0: [synoboot] No Caching mode page found
[ 114.260449] sd 5:0:0:0: [synoboot] Assuming drive cache: write through
[ 114.262817] usbcore: registered new interface driver usblp
[ 114.277037] synoboot: synoboot1 synoboot2
[ 114.287359] sd 5:0:0:0: [synoboot] No Caching mode page found
[ 114.294239] sd 5:0:0:0: [synoboot] Assuming drive cache: write through
[ 114.294247] sd 5:0:0:0: [synoboot] Attached SCSI disk
[ 114.294823] Adding 2097084k swap on /dev/md1. Priority:-1 extents:1 across:2097084k
[ 114.305162] Adding 1214460k swap on /dev/zram0. Priority:1 extents:1 across:1214460k SS
[ 114.314609] Adding 1214460k swap on /dev/zram1. Priority:1 extents:1 across:1214460k SS
[ 114.324151] Adding 1214460k swap on /dev/zram2. Priority:1 extents:1 across:1214460k SS
[ 114.333727] Adding 1214460k swap on /dev/zram3. Priority:1 extents:1 across:1214460k SS
[ 114.465382] usbcore: registered new interface driver usbhid
[ 114.471623] usbhid: USB HID core driver
[ 114.500254] synobios open /dev/ttyS1 success
[ 114.505166] 2022-1-8 16:46:54 UTC
[ 114.508904] synobios: load, major number 201
[ 114.513710] Brand: Synology
[ 114.516842] Model: DS-916+
[ 114.519865] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 114.529360] synobios cpu_arch proc entry initialized
[ 114.534920] synobios crypto_hw proc entry initialized
[ 114.540599] synobios syno_platform proc entry initialized
[ 114.601569] Syno_HddMon: Initialization completed.
[ 120.705968] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 121.174875] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 122.263345] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 122.321132] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 122.676106] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 122.787428] md: md3 stopped.
[ 122.792910] md: bind
[ 122.805973] md: raid0 personality registered for level 0
[ 122.812292] md/raid0:md3: md_size is 500099328 sectors.
[ 122.818175] md: RAID0 configuration for md3 - 1 zone
[ 122.823767] md: zone0=[sdee1]
[ 122.827130] zone-offset= 0KB, device-offset= 0KB, size= 250049664KB
[ 122.885406] md3: detected capacity change from 0 to 256050855936 [ 122.898693] md3: unknown partition table [ 122.904554] md: md2 stopped. [ 122.980392] md: bind
[ 122.983849] md: bind
[ 122.987160] md: bind
[ 122.990550] md: bind
[ 122.993970] md: bind
[ 122.997399] md: bind
[ 123.000920] md: bind
[ 123.018493] md: bind
[ 123.041537] xor: measuring software checksum speed
[ 123.056336] prefetch64-sse: 5444.000 MB/sec
[ 123.071330] generic_sse: 4992.000 MB/sec
[ 123.076109] xor: using function: prefetch64-sse (5444.000 MB/sec)
[ 123.115349] raid6: sse2x1 gen() 1265 MB/s
[ 123.136348] raid6: sse2x1 xor() 1488 MB/s
[ 123.157330] raid6: sse2x2 gen() 1003 MB/s
[ 123.178331] raid6: sse2x2 xor() 1820 MB/s
[ 123.199367] raid6: sse2x4 gen() 1296 MB/s
[ 123.220336] raid6: sse2x4 xor() 1777 MB/s
[ 123.225119] raid6: using algorithm sse2x4 gen() (1296 MB/s)
[ 123.225120] raid6: .... xor() 1777 MB/s, rmw enabled
[ 123.225122] raid6: using ssse3x2 recovery algorithm
[ 123.262603] md: raid6 personality registered for level 6
[ 123.268588] md: raid5 personality registered for level 5
[ 123.274555] md: raid4 personality registered for level 4
[ 123.280500] md: raidF1 personality registered for level 45
[ 123.287182] md/raid:md2: device sda3 operational as raid disk 0
[ 123.293831] md/raid:md2: device sded3 operational as raid disk 7
[ 123.300566] md/raid:md2: device sdec3 operational as raid disk 6
[ 123.307329] md/raid:md2: device sdeb3 operational as raid disk 5
[ 123.314147] md/raid:md2: device sdea3 operational as raid disk 4
[ 123.320891] md/raid:md2: device sdd3 operational as raid disk 3
[ 123.327531] md/raid:md2: device sdc3 operational as raid disk 2
[ 123.334239] md/raid:md2: device sdb3 operational as raid disk 1
[ 123.342876] md/raid:md2: allocated 8578kB
[ 123.347535] md/raid:md2: raid level 5 active with 8 out of 8 devices, algorithm 2
[ 123.355983] RAID conf printout:
[ 123.355990] --- level:5 rd:8 wd:8
[ 123.355996] disk 0, o:1, dev:sda3
[ 123.356000] disk 1, o:1, dev:sdb3
[ 123.356003] disk 2, o:1, dev:sdc3
[ 123.356007] disk 3, o:1, dev:sdd3
[ 123.356011] disk 4, o:1, dev:sdea3
[ 123.356015] disk 5, o:1, dev:sdeb3
[ 123.356018] disk 6, o:1, dev:sdec3
[ 123.356022] disk 7, o:1, dev:sded3
[ 123.391142] md2: detected capacity change from 0 to 27970944827392
[ 123.408056] md2: unknown partition table
[ 125.576278] flashcache_syno: Preread max memmory count=2048
[ 125.582520] flashcache_syno: Total pre-allocate bytes=67477504
[ 125.589050] flashcache_syno: Check and init Jobs finish
[ 125.594975] flashcache_syno: /dev/md2 exclude check success
[ 125.601236] flashcache_syno: /dev/md3 exclude check success
[ 125.607495] flashcache_syno: Cache Version: 11
[ 125.612471] flashcache_syno: Hash mapping = enable
[ 125.617835] device-mapper: flashcache: Can handle failure in creation
[ 125.625046] device-mapper: flashcache: Allocate 80000KB (25B per) mem for 3276800-entry cache(capacity:204800MB, asso ciativity:512, block size:128 sectors(64KB))
[ 125.894392] flashcache_syno: Create finish
[ 125.899045] bio: create slab at 1
[ 126.877689] bio: create slab at 2
[ 126.882523] Btrfs loaded
[ 126.885876] BTRFS: device label 2017.07.10-14:43:56 v15132 devid 1 transid 3230409 /dev/mapper/cachedev_0
[ 126.897314] BTRFS info (device dm-0): enabling auto syno reclaim space
[ 126.904634] BTRFS info (device dm-0): use ssd allocation scheme
[ 126.911259] BTRFS: has skinny extents
[ 161.229691] loop: module loaded
[ 161.369158] Synotify use 16384 event queue size
[ 161.381803] Synotify use 16384 event queue size
[ 161.388175] Synotify use 16384 event queue size
[ 161.934105] warning:
nginx' uses 32-bit capabilities (legacy support in use) [ 161.935184] warning:nginx' uses 32-bit capabilities (legacy support in use) [ 162.492108] ata1.00: configured for UDMA/133 [ 162.496913] ata1: EH complete [ 162.798662] ata2.00: configured for UDMA/133 [ 162.803481] ata2: EH complete [ 162.996800] ata3.00: configured for UDMA/133 [ 163.001615] ata3: EH complete [ 163.245010] ata4.00: configured for UDMA/133 [ 163.249818] ata4: EH complete [ 163.547226] ata5.00: configured for UDMA/133 [ 163.552142] ata5: EH complete [ 163.707679] ata5.01: configured for UDMA/133 [ 163.712570] ata5: EH complete [ 163.859076] ata5.02: configured for UDMA/133 [ 163.863971] ata5: EH complete [ 164.043302] ata5.03: configured for UDMA/133 [ 164.048381] ata5: EH complete [ 164.264760] ata5.04: configured for UDMA/133 [ 164.269647] ata5: EH complete [ 170.286817] iSCSI:target_core_rodsp_server.c:1027:rodsp_server_init RODSP server started, login_key(0011325bbf09). [ 170.322067] iSCSI:extent_pool.c:766:ep_init syno_extent_pool successfully initialized [ 170.427451] iSCSI:target_core_device.c:613:se_dev_align_max_sectors Rounding down aligned max_sectors from 4294967295 to 4294967288 [ 170.440821] iSCSI:target_core_configfs.c:5446:target_init_dbroot db_root: cannot open: /etc/target [ 170.451070] iSCSI:target_core_lunbackup.c:361:init_io_buffer_head 512 buffers allocated, total 2097152 bytes successf ully [ 170.541841] iSCSI:target_core_file.c:149:fd_attach_hba RODSP plugin for fileio is enabled. [ 170.551098] iSCSI:target_core_file.c:156:fd_attach_hba ODX Token Manager is enabled. [ 170.559964] iSCSI:target_core_multi_file.c:91:fd_attach_hba RODSP plugin for multifile is enabled. [ 170.570123] iSCSI:target_core_ep.c:795:ep_attach_hba RODSP plugin for epio is enabled. [ 170.579013] iSCSI:target_core_ep.c:802:ep_attach_hba ODX Token Manager is enabled. [ 170.932535] workqueue: max_active 1024 requested for vhost_scsi is out of range, clamping between 1 and 512 [ 219.510454] FAT-fs (synoboot2): fat_set_state: set=1 process=synopkicompatsy pid=10979 [ 219.572845] FAT-fs (synoboot2): fat_set_state: set=0 process=synopkicompatsy pid=10979 [ 220.973532] 8021q: 802.1Q VLAN Support v1.8 [ 220.978289] 8021q: adding VLAN 0 to HW filter on device eth0 [ 220.984831] 8021q: adding VLAN 0 to HW filter on device eth1 [ 221.351461] r8152: module verification failed: signature and/or required key missing - tainting kernel [ 221.384182] usbcore: registered new interface driver r8152 [ 221.394099] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 2 ep 2 with no TDs queued? [ 221.407136] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 2 ep 3 with no TDs queued? [ 221.416974] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 2 ep 6 with no TDs queued? [ 222.532097] usb 4-1: reset SuperSpeed USB device number 2 using etxhci_hcd-170202 [ 227.466304] fuse init (API version 7.22) [ 234.370508] netif_napi_add() called with weight 256 on device eth%d [ 234.384334] r8152 4-1:1.0 eth2: v2.15.0 (2021/04/15) [ 234.389912] r8152 4-1:1.0 eth2: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.[ 234.407344] r8152 4-1:1.0 eth2: chip rev 14 [ 236.499989] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 237.337490] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 237.348473] r8152 4-1:1.0 eth2: carrier on [ 237.890180] Synotify use 16384 event queue size [ 262.269094] Synotify use 16384 event queue size [ 271.442957] Synotify use 16384 event queue size [ 279.410882] Synotify use 16384 event queue size [ 279.418897] Synotify use 16384 event queue size [ 287.940961] Synotify use 16384 event queue size [ 287.946208] Synotify use 16384 event queue size
Output of
lsusbcommand|usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (xhci_hcd 0000:00:14.0) hub |1-5 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskStation 650063C8B9E41616) |usb2 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (xhci_hcd 0000:00:14.0) hub |usb3 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.108 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub |3-2 0463:ffff:0100 00 1.10 12MBit/s 20mA 1IF (EATON Ellipse PRO G355M18044) |usb4 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.108 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub |__4-1 0bda:8156:3100 00 3.20 5000MBit/s 256mA 1IF (Realtek USB 10/100/1G/2.5G LAN 001000001)
Output of
ifconfig -acommandeth0 Link encap:Ethernet HWaddr 00:11:32:5B:BF:09 inet addr:169.254.141.202 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth1 Link encap:Ethernet HWaddr 00:11:32:5B:BF:0A inet addr:169.254.70.2 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth2 Link encap:Ethernet HWaddr A0:CE:C8:F6:4D:17 inet addr:192.168.44.81 Bcast:192.168.44.255 Mask:255.255.255.0 inet6 addr: fd00::a2ce:c8ff:fef6:4d17/64 Scope:Global inet6 addr: fe80::a2ce:c8ff:fef6:4d17/64 Scope:Link inet6 addr: 2a02:8070:29a9:7b00:a2ce:c8ff:fef6:4d17/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6168 errors:0 dropped:0 overruns:0 frame:0 TX packets:10307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1562516 (1.4 MiB) TX bytes:10527824 (10.0 MiB)
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1409 errors:0 dropped:0 overruns:0 frame:0 TX packets:1409 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204856 (200.0 KiB) TX bytes:204856 (200.0 KiB)
sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)