search

bb-qq / r8152

Synology DSM driver for Realtek RTL8152/RTL8153/RTL8156 based adapters
GNU General Public License v2.0
2.05k stars 184 forks source link

Asustor AS-2.5G2(RTL8156B): does not appear in DS416j Network Interface list #287

Closed chatreip closed 1 year ago

chatreip commented 1 year ago

Description of the problem I installed the 2.15.0-1 driver, the installation process went smoothly, but there is no USB displayed in the network panel, the following is the system log, I hope to you solve it, thank you!

Description of your products DS416j CPU MARVELL Armada 388 88F6828 DDR3 512MB DSM 6.2.4-25556 Update 6 used driver: bb-qq 2.15.0-1 r8152-armada38x-2.14.0-2 from https://github.com/bb-qq/r8152/releases

Output of dmesg command

lsusb: |usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller f10f0000.usb3) hub |usb2 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller f10f0000.usb3) hub |usb3 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller f10f8000.usb3) hub |usb4 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller f10f8000.usb3) hub |4-1 0bda:8156:3100 00 3.20 5000MBit/s 256mA 1IF (Realtek USB 10/100/1G/2.5G LAN 0013000001) |usb5 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (ehci_hcd f1058000.usb) hub

ifconfig: eth0 Link encap:Ethernet HWaddr 00:11:32:::
inet addr:192.168.1.60 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: 2409:8a1e:2743:20e0:**:::/64 Scope:Global inet6 addr: fe80::211:::/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12077 errors:0 dropped:0 overruns:0 frame:0 TX packets:3300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1024 RX bytes:2812956 (2.6 MiB) TX bytes:995358 (972.0 KiB) Interrupt:193

eth1 Link encap:Ethernet HWaddr 00:E0:4C:::**
BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:134 errors:0 dropped:0 overruns:0 frame:0 TX packets:134 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:32047 (31.2 KiB) TX bytes:32047 (31.2 KiB)

sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

dmesg:

[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.105 (root@build4) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #25556 SMP Thu Jul 1 14:27:54 CST 2021 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Synology DS416j [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] free_area_init_node: node 0, pgdat 8066e340, node_mem_map 806d5000 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 131072 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 7 pages/cpu @80adf000 s7168 r8192 d13312 u32768 [ 0.000000] pcpu-alloc: s7168 r8192 d13312 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x3000000 root=/dev/md0 rw HddHotplug=4 syno_hw_version=DS416j hd_power_on_seq=4 ihd_num=4 netif_num=1 syno_hdd_detect=39,40,41,43 syno_hdd_enable=26,27,37,38 flash_size=8 [ 0.000000] Support HDD Hotplug. [ 0.000000] Synology Hardware Version: DS416j-j [ 0.000000] Internal HD num: 4 [ 0.000000] Internal netif num: 1 [ 0.000000] SYNO GPIO hdd detect pin: 39 40 41 43 [ 0.000000] SYNO GPIO hdd enable pin: 26 27 37 38 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 508188k/508188k available, 16100k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xfff00000 (1527 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x805fc1bc (6097 kB) .init : 0x805fd000 - 0x80636c00 ( 231 kB) .data : 0x80638000 - 0x8066ec80 ( 220 kB) .bss : 0x8066ec80 - 0x806d4f84 ( 409 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7

[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B [ 0.000442] Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) [ 0.060027] pid_max: default: 32768 minimum: 301 [ 0.060078] Security Framework initialized [ 0.060089] AppArmor: AppArmor initialized [ 0.060108] Mount-cache hash table entries: 512 [ 0.060465] Initializing cgroup subsys memory [ 0.060481] Disabling memory control group subsystem [ 0.060485] Initializing cgroup subsys devices [ 0.060489] Initializing cgroup subsys freezer [ 0.060492] Initializing cgroup subsys blkio [ 0.060517] CPU: Testing write buffer coherency: ok [ 0.060632] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060666] Setting up static identity map for 0x8047e320 - 0x8047e378 [ 0.060808] mvebu-pmsu: Initializing Power Management Service Unit [ 0.060842] Initializing CPU Reset module [ 0.061545] CPU1: Booted secondary processor [ 0.120602] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.120664] Brought up 2 CPUs [ 0.120673] SMP: Total of 2 processors activated (5311.69 BogoMIPS). [ 0.120676] CPU: All CPU(s) started in SVC mode. [ 0.120970] devtmpfs: initialized [ 0.123411] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.123597] xor: measuring software checksum speed [ 0.220484] arm4regs : 2365.600 MB/sec [ 0.320384] 8regs : 1630.400 MB/sec [ 0.420284] 32regs : 1658.800 MB/sec [ 0.420288] xor: using function: arm4regs (2365.600 MB/sec) [ 0.420293] pinctrl core: initialized pinctrl subsystem [ 0.420577] regulator-dummy: no parameters [ 0.420739] NET: Registered protocol family 16 [ 0.421329] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.423452] irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated [ 0.423808] irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated [ 0.426717] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.426722] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.433836] bio: create slab at 0 [ 0.600214] raid6: int32x1 gen() 191 MB/s [ 0.769971] raid6: int32x1 xor() 132 MB/s [ 0.939992] raid6: int32x2 gen() 267 MB/s [ 1.109722] raid6: int32x2 xor() 166 MB/s [ 1.279463] raid6: int32x4 gen() 272 MB/s [ 1.449311] raid6: int32x4 xor() 191 MB/s [ 1.619130] raid6: int32x8 gen() 303 MB/s [ 1.789069] raid6: int32x8 xor() 193 MB/s [ 1.789072] raid6: using algorithm int32x8 gen() (303 MB/s) [ 1.789076] raid6: .... xor() 193 MB/s, rmw enabled [ 1.789079] raid6: using intx1 recovery algorithm [ 1.789253] mvebu-pcie pcie-controller.3: PCIe0.0: link down [ 1.789275] mvebu-pcie pcie-controller.3: PCIe1.0: link down [ 1.789399] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 [ 1.789408] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.789414] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.789420] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.789436] pci 0000:00:01.0: [11ab:7846] type 01 class 0x060400 [ 1.789559] pci 0000:00:02.0: [11ab:7846] type 01 class 0x060400 [ 1.789667] PCI: bus0: Fast back to back transfers disabled [ 1.789675] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.789681] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.789772] PCI: bus1: Fast back to back transfers enabled [ 1.789780] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.789864] PCI: bus2: Fast back to back transfers enabled [ 1.789871] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.789891] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.789899] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.789907] PCI: enabling device 0000:00:01.0 (0140 -> 0143) [ 1.789913] PCI: enabling device 0000:00:02.0 (0140 -> 0143) [ 1.790440] SCSI subsystem initialized [ 1.790628] libata version 3.00 loaded. [ 1.791540] Switching to clocksource armada_370_xp_clocksource [ 1.791734] AppArmor: AppArmor Filesystem Enabled [ 1.792839] NET: Registered protocol family 2 [ 1.793194] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 1.793238] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 1.793276] TCP: Hash tables configured (established 4096 bind 4096) [ 1.793298] TCP: reno registered [ 1.793305] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.793317] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.793406] NET: Registered protocol family 1 [ 1.793540] RPC: Registered named UNIX socket transport module. [ 1.793545] RPC: Registered udp transport module. [ 1.793549] RPC: Registered tcp transport module. [ 1.793552] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.793563] PCI: CLS 64 bytes, default 64 [ 1.793654] Trying to unpack rootfs image as initramfs... [ 3.008052] Freeing initrd memory: 3436K (9f6ce000 - 9fa29000) [ 3.008294] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 3.009821] Initialise module verification [ 3.009860] audit: initializing netlink socket (disabled) [ 3.009881] type=2000 audit(3.000:1): initialized [ 3.011146] VFS: Disk quotas dquot_6.5.2 [ 3.011202] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 3.011503] NFS: Registering the id_resolver key type [ 3.011527] Key type id_resolver registered [ 3.011532] Key type id_legacy registered [ 3.011584] msgmni has been set to 999 [ 3.012155] async_tx: api initialized (async) [ 3.012163] Key type asymmetric registered [ 3.012167] Asymmetric key parser 'x509' registered [ 3.012360] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 3.012367] io scheduler noop registered [ 3.012380] io scheduler cfq registered (default) [ 3.013263] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 3.013810] mv_xor f1060800.xor: Marvell shared XOR driver [ 3.051942] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 3.081896] mv_xor f1060800.xor: freeing 1 in use descriptors! [ 3.081907] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 3.083027] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.121883] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 3.151894] mv_xor f1060900.xor: freeing 1 in use descriptors! [ 3.151905] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 3.153499] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.175513] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A [ 3.997414] console [ttyS0] enabled [ 4.021425] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A [ 4.038890] brd: module loaded [ 4.041977] Loading iSCSI transport class v2.0-870. [ 4.049532] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 4.058391] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 4.068847] scsi0 : ahci_mv_platform [ 4.073047] scsi1 : ahci_mv_platform [ 4.077125] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 [ 4.085098] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 [ 12.471566] ata1: link is slow to respond, please be patient (ready=0) [ 16.091567] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 16.117337] ata1.00: ATA-10: ST4000VN008-2DR166, SC60, max UDMA/133 [ 16.123638] ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 16.130453] ata1.00: SN: ZDH30N72 [ 16.135837] ata1.00: configured for UDMA/133 [ 16.141166] scsi 0:0:0:0: Direct-Access ATA ST4000VN008-2DR166 SC60 PQ: 0 ANSI: 5 [ 16.150884] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB) [ 16.151515] Delay 5 seconds to wait for disk 2 ready. [ 16.163751] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 16.169325] sd 0:0:0:0: [sda] Write Protect is off [ 16.174148] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 16.174197] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 16.249949] sda: sda1 sda2 sda3 [ 16.255021] sd 0:0:0:0: [sda] Attached SCSI disk [ 29.511565] ata2: link is slow to respond, please be patient (ready=0) [ 33.371568] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 33.385777] ata2.00: ATA-10: ST4000VN008-2DR166, SC60, max UDMA/133 [ 33.392079] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 33.398894] ata2.00: SN: ZDH32SQP [ 33.404268] ata2.00: configured for UDMA/133 [ 33.409581] scsi 1:0:0:0: Direct-Access ATA ST4000VN008-2DR166 SC60 PQ: 0 ANSI: 5 [ 33.419268] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB) [ 33.427062] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 33.431880] ahci_mv f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 33.431886] ahci_mv f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 33.435025] scsi2 : ahci_mv_platform [ 33.435869] scsi3 : ahci_mv_platform [ 33.436461] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 60 [ 33.436464] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 60 [ 33.436470] Delay 5 seconds to wait for disk 3 ready. [ 33.478106] sd 1:0:0:0: [sdb] Write Protect is off [ 33.482930] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 33.482976] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 33.553884] sdb: sdb1 sdb2 sdb3 [ 33.558945] sd 1:0:0:0: [sdb] Attached SCSI disk [ 46.791566] ata3: link is slow to respond, please be patient (ready=0) [ 51.591565] ata3: softreset failed (device not ready) [ 51.596636] ata3: SRST fail, set srst fail flag [ 56.941568] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 56.947776] ata3: link reset sucessfully clear error flags [ 56.966784] ata3.00: ATA-9: WDC WD120EMAZ-11BLFA0, 81.00A81, max UDMA/133 [ 56.973608] ata3.00: 23437770752 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 56.980510] ata3.00: SN:5PGGEL6D [ 56.986908] ata3.00: configured for UDMA/133 [ 56.991568] scsi 2:0:0:0: Direct-Access WDC WD120EMAZ-11BLFA0 81.0 PQ: 0 ANSI: 5 [ 57.001240] sd 2:0:0:0: [sdc] 23437770752 512-byte logical blocks: (12.0 TB/10.9 TiB) [ 57.009118] sd 2:0:0:0: [sdc] 4096-byte physical blocks [ 57.011801] Delay 5 seconds to wait for disk 4 ready. [ 57.019813] sd 2:0:0:0: [sdc] Write Protect is off [ 57.024636] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 57.024681] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 57.447523] sdc: sdc1 sdc2 sdc3 [ 57.452558] sd 2:0:0:0: [sdc] Attached SCSI disk [ 70.391565] ata4: link is slow to respond, please be patient (ready=0) [ 75.191565] ata4: softreset failed (device not ready) [ 75.196638] ata4: SRST fail, set srst fail flag [ 78.561567] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 78.567774] ata4: link reset sucessfully clear error flags [ 78.701217] ata4.00: ATA-9: WDC WD120EMFZ-11A6JA0, 81.00A81, max UDMA/133 [ 78.708041] ata4.00: 23437770752 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 78.714947] ata4.00: SN:Z2JSGGDT [ 78.868901] ata4.00: configured for UDMA/133 [ 78.873560] scsi 3:0:0:0: Direct-Access WDC WD120EMFZ-11A6JA0 81.0 PQ: 0 ANSI: 5 [ 78.883263] sd 3:0:0:0: [sdd] 23437770752 512-byte logical blocks: (12.0 TB/10.9 TiB) [ 78.888897] m25p80 spi0.0: n25q064 (8192 Kbytes) [ 78.888913] Searching for RedBoot partition table in spi0.0 at offset 0x7f0000 [ 78.903032] sd 3:0:0:0: [sdd] 4096-byte physical blocks [ 78.908630] sd 3:0:0:0: [sdd] Write Protect is off [ 78.913454] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 78.913500] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 78.989021] 6 RedBoot partitions found on MTD device spi0.0 [ 78.994640] Creating 6 MTD partitions on "spi0.0": [ 78.999451] 0x000000000000-0x0000000f0000 : "RedBoot" [ 79.005732] 0x0000000f0000-0x0000003c0000 : "zImage" [ 79.012125] 0x0000003c0000-0x0000007d0000 : "rd.gz" [ 79.018340] 0x0000007d0000-0x0000007e0000 : "vendor" [ 79.023802] vender Mac0 address : 00:11:32:..* [ 79.028702] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 79.034571] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 79.040426] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 79.046301] serial number='16A0NAN235301' [ 79.051285] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 79.058394] 0x0000007f0000-0x000000800000 : "FIS directory" [ 79.068418] SoC: model = 0x6828, revision = 0x4 [ 79.073051] mvPncVirtBase = 0xa0c00000, pncTcamSize = 1024 [ 79.078558] o 3 Giga ports supported [ 79.082334] o SKB recycle supported for SWF (Disabled) [ 79.087667] o NETA acceleration mode 4 [ 79.091608] o BM supported for CPU: 4 BM pools [ 79.096242] o PnC supported (Enabled) [ 79.100091] o RX Queue support: 8 Queues 512 Descriptors [ 79.105776] o TX Queue support: 8 Queues * 1024 Descriptors [ 79.111543] o GSO supported [ 79.114522] o GRO supported [ 79.117498] o Receive checksum offload supported [ 79.122308] o Transmit checksum offload supported [ 79.127203] o Driver ERROR statistics enabled [ 79.131752] o Driver INFO statistics enabled [ 79.135838] sdd: sdd1 sdd2 sdd3 [ 79.137689] sd 3:0:0:0: [sdd] Attached SCSI disk [ 79.144093] o Driver DEBUG statistics enabled

[ 79.151166] port #0: is_sgmii=1, is_rgmii=0, phy_addr=1 [ 79.156454] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800

[ 79.166268] o Port 0 is connected to Linux netdevice [ 79.175848] o eth0, ifindex = 2, GbE port = 0 [ 79.180587] o eth0, phy chipid = 1410dd0, Support WOL = 32 [ 79.189867] giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform)

[ 79.198016] libphy: orion_mdio_bus: probed [ 79.204304] mdio_bus f1072004.mdio-mi: cannot get PHY at address 0 [ 79.211904] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 79.261743] i2c /dev entries driver [ 79.267040] Syno_HddMon: Initialization completed. [ 79.281971] armada_thermal f10e4078.thermal: Overheat threshold between 92..107 [ 79.289942] md: linear personality registered for level -1 [ 79.295468] md: raid0 personality registered for level 0 [ 79.300805] md: raid1 personality registered for level 1 [ 79.306161] md: raid10 personality registered for level 10 [ 79.311884] md: raid6 personality registered for level 6 [ 79.317220] md: raid5 personality registered for level 5 [ 79.322566] md: raid4 personality registered for level 4 [ 79.328128] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com [ 79.336613] cpuidle: using governor ladder [ 79.341007] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 [ 79.350371] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) [ 79.358884] mvCesaInit: channels=2, session=640, queue=256 [ 79.375357] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode [ 79.384801] cesadev_init(8061baf4) [ 79.388968] TCP: cubic registered [ 79.392321] NET: Registered protocol family 17 [ 79.396830] Key type dns_resolver registered [ 79.401197] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 79.408927] Registering suspend init for this board failed [ 79.417148] Loading module verification blacklist certificates [ 79.423035] Loading module verification certificates [ 79.428068] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329' [ 79.443736] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089' [ 79.454170] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28' [ 79.466075] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5' [ 79.476218] registered taskstats version 1 [ 79.480365] regulator-dummy: disabling [ 79.484449] Freeing unused kernel memory: 228K (805fd000 - 80636000) [ 79.663938] usbcore: registered new interface driver usbfs [ 79.671463] usbcore: registered new interface driver hub [ 79.679786] usbcore: registered new device driver usb [ 79.732378] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 79.775835] xhci-hcd f10f0000.usb3: failed to get Vbus gpio [ 79.781439] xhci-hcd f10f0000.usb3: USB2 Vbus gpio -1 [ 79.786551] xhci-hcd f10f0000.usb3: power control disabled [ 79.792069] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 79.797414] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 79.805156] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 79.811453] xHCI xhci_add_endpoint called for root hub [ 79.811461] xHCI xhci_check_bandwidth called for root hub [ 79.814007] hub 1-0:1.0: USB hub found [ 79.817795] hub 1-0:1.0: 1 port detected [ 79.821851] xhci-hcd f10f0000.usb3: USB3 Vbus gpio -1 [ 79.826933] xhci-hcd f10f0000.usb3: power control disabled [ 79.832475] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 79.837822] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 79.845911] xHCI xhci_add_endpoint called for root hub [ 79.845921] xHCI xhci_check_bandwidth called for root hub [ 79.846258] hub 2-0:1.0: USB hub found [ 79.850048] hub 2-0:1.0: 1 port detected [ 79.854187] xhci-hcd f10f8000.usb3: USB2 Vbus gpio 58 [ 79.859266] xhci-hcd f10f8000.usb3: power control enabled [ 79.864731] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 79.870086] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 79.882362] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 79.889733] xHCI xhci_add_endpoint called for root hub [ 79.889742] xHCI xhci_check_bandwidth called for root hub [ 79.891929] hub 3-0:1.0: USB hub found [ 79.895716] hub 3-0:1.0: 1 port detected [ 79.899760] xhci-hcd f10f8000.usb3: USB3 Vbus gpio 58 [ 79.904873] xhci-hcd f10f8000.usb3: power control enabled [ 79.910301] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 79.915663] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 79.925526] xHCI xhci_add_endpoint called for root hub [ 79.925535] xHCI xhci_check_bandwidth called for root hub [ 79.927653] hub 4-0:1.0: USB hub found [ 79.931437] hub 4-0:1.0: 1 port detected [ 80.004860] ehci-orion: EHCI orion driver [ 80.009020] orion-ehci f1058000.usb: USB2 Vbus gpio 59 [ 80.014252] orion-ehci f1058000.usb: power control enabled [ 80.019763] orion-ehci f1058000.usb: EHCI Host Controller [ 80.025205] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 5 [ 80.032881] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 [ 80.051580] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 80.058171] hub 5-0:1.0: USB hub found [ 80.061988] hub 5-0:1.0: 1 port detected [ 80.121814] ds416j_synobios: module license 'Synology Inc.' taints kernel. [ 80.128721] Disabling lock debugging due to kernel taint [ 80.134971] Synobios DS416j GPIO initialized [ 80.139472] 2023-2-11 10:56:25 UTC [ 80.142918] synobios: load, major number 201 [ 80.147214] Brand: Synology [ 80.150038] Model: DS-416j [ 80.152781] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 80.161272] synobios cpu_arch proc entry initialized [ 80.166264] synobios crypto_hw proc entry initialized [ 80.171337] synobios syno_platform proc entry initialized [ 80.176831] synobios open /dev/ttyS1 success [ 80.196227] synobios: unload [ 80.221103] md: Autodetecting RAID arrays. [ 80.290427] md: invalid raid superblock magic on sda3 [ 80.295521] md: sda3 does not have a valid v0.90 superblock, not importing! [ 80.565852] md: invalid raid superblock magic on sdb3 [ 80.570925] md: sdb3 does not have a valid v0.90 superblock, not importing! [ 80.619736] md: invalid raid superblock magic on sdc3 [ 80.624818] md: sdc3 does not have a valid v0.90 superblock, not importing! [ 80.679338] md: invalid raid superblock magic on sdd3 [ 80.684418] md: sdd3 does not have a valid v0.90 superblock, not importing! [ 80.691415] md: Scanned 12 and added 8 devices. [ 80.695968] md: autorun ... [ 80.698771] md: considering sda1 ... [ 80.702375] md: adding sda1 ... [ 80.705619] md: sda2 has different UUID to sda1 [ 80.710172] md: adding sdb1 ... [ 80.713420] md: sdb2 has different UUID to sda1 [ 80.717974] md: adding sdc1 ... [ 80.721216] md: sdc2 has different UUID to sda1 [ 80.725773] md: adding sdd1 ... [ 80.729016] md: sdd2 has different UUID to sda1 [ 80.733591] md: created md0 [ 80.736394] md: bind [ 80.739139] md: bind [ 80.741880] md: bind [ 80.744615] md: bind [ 80.747352] md: running: [ 80.752438] md/raid1:md0: active with 4 out of 4 mirrors [ 80.881704] md0: detected capacity change from 0 to 2549940224 [ 80.887756] md: considering sda2 ... [ 80.891360] md: adding sda2 ... [ 80.894637] md: adding sdb2 ... [ 80.897891] md: adding sdc2 ... [ 80.901148] md: adding sdd2 ... [ 80.908382] md: created md1 [ 80.911196] md: bind [ 80.913989] md: bind [ 80.916741] md: bind [ 80.919493] md: bind [ 80.922271] md: running: [ 80.927805] md/raid1:md1: active with 4 out of 4 mirrors [ 80.999773] md1: detected capacity change from 0 to 2147418112 [ 81.005858] md: ... autorun DONE. [ 81.331676] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd [ 81.351885] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [ 81.380765] md0: unknown partition table [ 84.046009] EXT4-fs (md0): barriers disabled [ 84.052033] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: [ 86.849681] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: barrier=1 [ 88.290786] EXT4-fs (md0): re-mounted. Opts: (null) [ 96.795756] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 96.801219] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 96.806777] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 96.812293] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 97.609331] md1: unknown partition table [ 97.982504] Adding 2097084k swap on /dev/md1. Priority:-1 extents:1 across:2097084k [ 98.941060] systemd-udevd[1626]: starting version 204 [ 106.621814] NET: Registered protocol family 10 [ 106.728599] sit: IPv6 over IPv4 tunneling driver [ 107.300686] init: syno-auth-check main process (3229) killed by TERM signal [ 108.472343] encryptfs using the OCF package. [ 108.614240] fuse init (API version 7.22) [ 108.784005] Loading modules backported from Linux version v3.18.1-0-g39ca484 [ 108.791087] Backport generated by backports.git v3.18.1-1-0-g5e9ec4c [ 108.935572] exFAT: Version 1.2.9 [ 108.964609] Synobios DS416j GPIO initialized [ 108.969095] 2023-2-11 10:56:53 UTC [ 108.972529] synobios: load, major number 201 [ 108.976820] Brand: Synology [ 108.979643] Model: DS-416j [ 108.982381] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 108.990870] synobios cpu_arch proc entry initialized [ 108.995863] synobios crypto_hw proc entry initialized [ 109.000937] synobios syno_platform proc entry initialized [ 109.006440] synobios open /dev/ttyS1 success [ 109.023146] Starting SW init... [ 109.085790] synobios: unload [ 109.836522] Synobios DS416j GPIO initialized [ 109.841006] 2023-2-11 10:56:54 UTC [ 109.844459] synobios: load, major number 201 [ 109.848749] Brand: Synology [ 109.851591] Model: DS-416j [ 109.854320] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 109.862824] synobios cpu_arch proc entry initialized [ 109.867810] synobios crypto_hw proc entry initialized [ 109.872895] synobios syno_platform proc entry initialized [ 109.878383] synobios open /dev/ttyS1 success [ 111.119998] eth0: mac address changed [ 111.164841] pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added [ 111.172440] eth0: link up [ 111.175133] eth0: started [ 111.175146] eth0: [ 111.175147] link up [ 111.175148] , full duplex [ 111.175149] , speed [ 111.175149] 1 Gbps [ 111.308117] ip_tables: (C) 2000-2006 Netfilter Core Team [ 111.379864] nf_conntrack version 0.5.0 (7997 buckets, 31988 max) [ 111.745124] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 115.580259] md: md2 stopped. [ 115.657879] md: bind [ 115.661768] md: bind [ 115.714595] md/raid1:md2: active with 2 out of 2 mirrors [ 115.899505] md2: detected capacity change from 0 to 11995200880640 [ 115.908131] md2: unknown partition table [ 116.099872] md: md3 stopped. [ 116.121661] md: bind [ 116.161924] md: bind [ 116.241713] md/raid1:md3: active with 2 out of 2 mirrors [ 116.395738] md3: detected capacity change from 0 to 3995849261056 [ 116.460919] md3: unknown partition table [ 117.300170] bio: create slab at 1 [ 123.293897] EXT4-fs (md3): barriers disabled [ 123.369780] EXT4-fs (md3): mounted filesystem with writeback data mode. Opts: usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,synoacl,data=writeback,oldalloc [ 123.461924] EXT4-fs (dm-1): barriers disabled [ 123.882201] EXT4-fs (dm-1): mounted filesystem with writeback data mode. Opts: usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,synoacl,data=writeback,oldalloc [ 126.983925] Synotify use 16384 event queue size [ 126.988574] Synotify use 16384 event queue size [ 131.090084] ehci-pci: EHCI PCI platform driver [ 131.679722] usbcore: registered new interface driver usb-storage [ 131.777764] usbcore: registered new interface driver usblp [ 132.130353] usbcore: registered new interface driver usbhid [ 132.136007] usbhid: USB HID core driver [ 134.410241] iSCSI:target_core_rodsp_server.c:1027:rodsp_server_init RODSP server started, login_key(00113266b0b3). [ 134.483749] iSCSI:extent_pool.c:766:ep_init syno_extent_pool successfully initialized [ 134.584168] iSCSI:target_core_device.c:617:se_dev_align_max_sectors Rounding down aligned max_sectors from 4294967295 to 4294967288 [ 134.596385] iSCSI:target_core_lunbackup.c:361:init_io_buffer_head 512 buffers allocated, total 2097152 bytes successfully [ 134.766470] iSCSI:target_core_file.c:146:fd_attach_hba RODSP plugin for fileio is enabled. [ 134.774813] iSCSI:target_core_file.c:153:fd_attach_hba ODX Token Manager is enabled. [ 134.793132] iSCSI:target_core_multi_file.c:91:fd_attach_hba RODSP plugin for multifile is enabled. [ 134.821662] iSCSI:target_core_ep.c:786:ep_attach_hba RODSP plugin for epio is enabled. [ 134.829622] iSCSI:target_core_ep.c:793:ep_attach_hba ODX Token Manager is enabled. [ 137.410052] Synotify use 16384 event queue size [ 137.601118] Synotify use 16384 event queue size [ 139.076803] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 139.726587] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 139.734564] NFSD: starting 90-second grace period (net 80669080) [ 141.173452] ata1.00: configured for UDMA/133 [ 141.177756] ata1: EH complete [ 141.844436] ata2.00: configured for UDMA/133 [ 141.848732] ata2: EH complete [ 142.330987] ata3.00: configured for UDMA/133 [ 142.335331] ata3: EH complete [ 143.110665] ata4.00: configured for UDMA/133 [ 143.115023] ata4: EH complete [ 144.204973] warning: `nginx' uses 32-bit capabilities (legacy support in use) [ 148.902116] loop: module loaded [ 153.407935] findhostd uses obsolete (PF_INET,SOCK_PACKET) [ 156.716312] r8152: module verification failed: signature and/or required key missing - tainting kernel [ 156.728014] usbcore: registered new interface driver r8152 [ 156.891821] usb 4-1: reset SuperSpeed USB device number 2 using xhci-hcd [ 156.911818] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [ 156.961669] xhci-hcd f10f8000.usb3: xHCI xhci_drop_endpoint called with disabled ep 9c0d7600 [ 156.970212] xhci-hcd f10f8000.usb3: xHCI xhci_drop_endpoint called with disabled ep 9c0d762c [ 156.978779] xhci-hcd f10f8000.usb3: xHCI xhci_drop_endpoint called with disabled ep 9c0d7658 [ 164.408742] init: syno-check-disk-compatibility main process (10956) terminated with status 255 [ 164.517938] Synotify use 16384 event queue size [ 164.522629] Synotify use 16384 event queue size [ 173.201818] netif_napi_add() called with weight 256 on device eth%d [ 173.251605] r8152 4-1:1.0 eth1: v2.14.0 (2020/09/24) [ 173.256661] r8152 4-1:1.0 eth1: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.

[ 173.990470] usbcore: registered new interface driver snd-usb-audio [ 174.412816] usbcore: registered new interface driver snd-usb-hiface [ 200.681275] Synotify use 16384 event queue size [ 200.686002] Synotify use 16384 event queue size [ 201.181133] init: synocontentextractd main process ended, respawning [ 208.616428] Synotify use 16384 event queue size [ 208.621040] Synotify use 16384 event queue size [ 231.642605] Synotify use 16384 event queue size

chatreip commented 1 year ago

Add some content, the log of the plug-in startup process:

`[179161.248138] usb 4-1: reset SuperSpeed USB device number 3 using xhci-hcd [179161.268223] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [179161.277469] xhci-hcd f10f8000.usb3: xHCI xhci_drop_endpoint called with disabled ep 9c64ac00 [179161.286067] xhci-hcd f10f8000.usb3: xHCI xhci_drop_endpoint called with disabled ep 9c64ac2c [179161.294669] xhci-hcd f10f8000.usb3: xHCI xhci_drop_endpoint called with disabled ep 9c64ac58 [179161.498085] r8152 4-1:1.0 eth1: v2.14.0 (2020/09/24) [179161.503178] r8152 4-1:1.0 eth1: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.

[179161.519172] usbcore: registered new interface driver r8152 [179166.701827] ifconfig: page allocation failure: order:4, mode:0x40d0 [179166.708248] CPU: 1 PID: 31638 Comm: ifconfig Tainted: PF O 3.10.105 #25556 [179166.716049] [<8001462c>] (unwind_backtrace+0x0/0xec) from [<8001171c>] (show_stack+0x10/0x14) [179166.724761] [<8001171c>] (show_stack+0x10/0x14) from [<8009ed8c>] (warn_alloc_failed+0xe4/0x11c) [179166.733718] [<8009ed8c>] (warn_alloc_failed+0xe4/0x11c) from [<800a1048>] (alloc_pages_nodemask+0x58c/0x788) [179166.743908] [<800a1048>] (alloc_pages_nodemask+0x58c/0x788) from [<7f7c49cc>] (alloc_rx_agg+0x4c/0x134 [r8152]) [179166.754359] [<7f7c49cc>] (alloc_rx_agg+0x4c/0x134 [r8152]) from [<7f7c70bc>] (rtl8152_open+0xb4/0x3e8 [r8152]) [179166.764563] [<7f7c70bc>] (rtl8152_open+0xb4/0x3e8 [r8152]) from [<803c7638>] (dev_open+0x98/0xf8) [179166.773794] [<803c7638>] (__dev_open+0x98/0xf8) from [<803c7878>] (dev_change_flags+0x94/0x128) [179166.782831] [<803c7878>] (__dev_change_flags+0x94/0x128) from [<803c7978>] (dev_change_flags+0x10/0x48) [179166.792392] [<803c7978>] (dev_change_flags+0x10/0x48) from [<8041f168>] (devinet_ioctl+0x640/0x714) [179166.801610] [<8041f168>] (devinet_ioctl+0x640/0x714) from [<803af69c>] (sock_ioctl+0x138/0x288) [179166.810453] [<803af69c>] (sock_ioctl+0x138/0x288) from [<800ecb38>] (do_vfs_ioctl+0x4b4/0xaa8) [179166.819208] [<800ecb38>] (do_vfs_ioctl+0x4b4/0xaa8) from [<800ed19c>] (SyS_ioctl+0x70/0x80) [179166.827701] [<800ed19c>] (SyS_ioctl+0x70/0x80) from [<8000e080>] (ret_fast_syscall+0x0/0x38) [179166.836277] Mem-info: [179166.838655] Normal per-cpu: [179166.841548] CPU 0: hi: 186, btch: 31 usd: 180 [179166.846444] CPU 1: hi: 186, btch: 31 usd: 0 [179166.851353] active_anon:11607 inactive_anon:14352 isolated_anon:0 active_file:15530 inactive_file:14309 isolated_file:0 unevictable:540 dirty:0 writeback:323 unstable:0 free:31737 slab_reclaimable:7145 slab_unreclaimable:24417 mapped:9568 shmem:5571 pagetables:3287 bounce:0 free_cma:0 [179166.884648] Normal free:126948kB min:8192kB low:10240kB high:12288kB active_anon:46428kB inactive_anon:57408kB active_file:62120kB inactive_file:57236kB unevictable:2160kB isolated(anon):0kB isolated(file):0kB present:524288kB managed:508188kB mlocked:2160kB dirty:0kB writeback:0kB mapped:38272kB shmem:22284kB slab_reclaimable:28580kB slab_unreclaimable:97668kB kernel_stack:3808kB pagetables:13148kB unstable:0kB bounce:0kB free_cma:0kB writeback_tmp:0kB pages_scanned:2 all_unreclaimable? no [179166.928376] lowmem_reserve[]: 0 0 [179166.931828] Normal: 153394kB (UEM) 58478kB (UEM) 106616kB (EMR) 2232kB (EM) 064kB 1128kB (R) 1256kB (R) 1512kB (R) 01024kB 02048kB 0*4096kB = 126788kB [179166.946578] 40310 total pagecache pages [179166.950527] 4837 pages in swap cache [179166.954207] Swap cache stats: add 51238, delete 46401, find 291772/292881 [179166.961132] Free swap = 1939440kB [179166.964641] Total swap = 2097084kB [179166.971215] 131072 pages of RAM [179166.974460] 32933 free pages [179166.977443] 3109 reserved pages [179166.980698] 31550 slab pages [179166.983676] 61912 pages shared [179166.986827] 4837 pages swap cached`

bb-qq commented 1 year ago

It appears to be running out of memory. There are changes in the latest drivers to reduce memory consumption. Perhaps that change might help. Can you upgrade DSM to 7?

Barlos commented 1 year ago

Try to change to other USB port.

bb-qq commented 1 year ago

I have made the latest driver available for DSM 6.2 as well, so please try it.

bb-qq commented 1 year ago

I would like to close this issue since there has been no response. If you have any questions, feel free to re-open it.