search

bdring / FluidNC

The next generation of motion control firmware
Other
1.6k stars 383 forks source link

Problem: yaml file. #1272

Open Hooks321 opened 3 months ago

Hooks321 commented 3 months ago

Wiki Search Terms

Only new here.

Controller Board

6-pack ESP-WROOM-32

Machine Description

Gantry Laser setup.

Input Circuits

No response

Configuration file

Wont past

Startup Messages

Cannot open configuration file:<your_filename>

User Interface Software

Fluidterm

What happened?

Every time I upload the config yaml file it said the configuration is invalid.??? any help would be great thanks.

GCode File

?

Other Information

?

breiler commented 3 months ago

Can you show the output from the command $SS

Hooks321 commented 3 months ago

Hope this helps.

On Fri, 26 July 2024, 9:04 pm Joacim Breiler, @.***> wrote:

Can you show the output from the command $SS

— Reply to this email directly, view it on GitHub https://github.com/bdring/FluidNC/issues/1272#issuecomment-2252522504, or unsubscribe https://github.com/notifications/unsubscribe-auth/AXQPGWHSZZBCMSXEK6F33UDZOIUKLAVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJSGUZDENJQGQ . You are receiving this because you authored the thread.Message ID: @.***>

breiler commented 3 months ago

Did you try to attach something? That doesn't work when using email - you need to go to the issue to do that: https://github.com/bdring/FluidNC/issues/1272

Hooks321 commented 3 months ago

This maybe better.

On Fri, 26 July 2024, 9:15 pm Gary Hawkins, @.***> wrote:

On Fri, 26 July 2024, 9:13 pm Gary Hawkins, @.***> wrote:

Hope this helps.

On Fri, 26 July 2024, 9:04 pm Joacim Breiler, @.***> wrote:

Can you show the output from the command $SS

— Reply to this email directly, view it on GitHub https://github.com/bdring/FluidNC/issues/1272#issuecomment-2252522504, or unsubscribe https://github.com/notifications/unsubscribe-auth/AXQPGWHSZZBCMSXEK6F33UDZOIUKLAVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJSGUZDENJQGQ . You are receiving this because you authored the thread.Message ID: @.***>

Hooks321 commented 3 months ago

Did that come through?

On Fri, 26 July 2024, 9:16 pm Joacim Breiler, @.***> wrote:

Did you try to attach something? That doesn't work when using email - you need to go to the issue to do that: #1272 https://github.com/bdring/FluidNC/issues/1272

— Reply to this email directly, view it on GitHub https://github.com/bdring/FluidNC/issues/1272#issuecomment-2252542145, or unsubscribe https://github.com/notifications/unsubscribe-auth/AXQPGWGDVVVIE65MURIDRETZOIV2RAVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJSGU2DEMJUGU . You are receiving this because you authored the thread.Message ID: @.***>

Hooks321 commented 3 months ago

20240726_211518 Sorry for the delay.

breiler commented 3 months ago

The <your_filename> is probably the default setting, select your config file with: $Config/Filename=Laser Home XYZ (1).yaml

Or you could use the https://installer.fluidnc.com/ go to the "File browser" and click the "Select Config" button:

image

Hooks321 commented 3 months ago

Still trying.

Hooks321 commented 3 months ago

OK, selected active config. what do I do next.

breiler commented 3 months ago

Restart the controller and check the boot messages.

If you are doing this from the https://installer.fluidnc.com/ just go to the "Terminal" page and hit "Restart"

Hooks321 commented 3 months ago

Hi, looks like its loaded OK now. Thanks for all your help so far, much appreciated. Is there a way for this card to be seen in Lightburn software now.?

MitchBradley commented 3 months ago

Did you search for "lightburn" in the fluidnc wiki?

Hooks321 commented 3 months ago

Yes, I found it. Thankyou.

On Sat, 27 July 2024, 9:45 am Mitch Bradley, @.***> wrote:

Did you search for "lightburn" in the fluidnc wiki?

— Reply to this email directly, view it on GitHub https://github.com/bdring/FluidNC/issues/1272#issuecomment-2253653101, or unsubscribe https://github.com/notifications/unsubscribe-auth/AXQPGWFYYYYOIQS2XPNE5RLZOLNQ3AVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJTGY2TGMJQGE . You are receiving this because you authored the thread.Message ID: @.***>