search

betaflight / betaflight-configurator

Cross platform configuration tool for the Betaflight firmware
GNU General Public License v3.0
2.52k stars 895 forks source link

vtx_power is not saved #2849

Closed palgy closed 2 years ago

palgy commented 2 years ago

Describe the bug

vtx_power is not saved , when setting from configurator or from cli

To Reproduce

update vtx power from configurator and save or from cli set vtx_power = 5 save disconnect the flight controller from USB wait 10 sec check the vtx_power ... value was not saved

Expected behavior

vtx_power should be saved

Configurator version

10.8.0 RC3

Flight controller configuration

  # REPLACE THIS LINE BY THE OUTPUT OF YOUR `diff`

Add any other context about the problem that you think might be relevant here

defaults nosave

version

Betaflight / STM32F7X2 (S7X2) 4.3.0 Feb 1 2022 / 20:14:54 (3267f0417) MSP API: 1.44

config: manufacturer_id: SPBE, board_name: SPEEDYBEEF7V2, version: 55694498, date: 2021-05-15T13:56:51Z

start the command batch

batch start

reset configuration to default settings

defaults nosave

board_name SPEEDYBEEF7V2 manufacturer_id SPBE mcu_id 0030002f3756501120383558 signature

name: AOS 5

feature

feature -ESC_SENSOR feature GPS feature TELEMETRY

serial

serial 1 8192 115200 57600 0 115200 serial 5 2 115200 57600 0 115200

beacon

beacon RX_LOST beacon RX_SET

aux

aux 0 0 0 1775 2100 0 0 aux 1 1 2 1325 1650 0 0 aux 2 27 1 1775 2100 0 0 aux 3 13 4 1750 2100 0 0 aux 4 35 3 1750 2100 0 0

vtxtable

vtxtable bands 7 vtxtable channels 8 vtxtable band 1 BOSCAM_A A CUSTOM 5865 5845 5825 5805 5785 5765 5745 5725 vtxtable band 2 BOSCAM_B B CUSTOM 5733 5752 5771 5790 5809 5828 5847 5866 vtxtable band 3 BOSCAM_E E CUSTOM 5705 5685 5665 5645 5885 5905 5925 5945 vtxtable band 4 FATSHARK F CUSTOM 5740 5760 5780 5800 5820 5840 5860 5880 vtxtable band 5 RACEBAND R CUSTOM 5658 5695 5732 5769 5806 5843 5880 5917 vtxtable band 6 LOWRACE L CUSTOM 5333 5373 5413 5453 5493 5533 5573 5613 vtxtable band 7 IMD6 I CUSTOM 5732 5765 5828 5840 5866 5740 0 0 vtxtable powerlevels 5 vtxtable powervalues 10 2 25 100 400 vtxtable powerlabels 10 RCE 25 100 400

master

set dyn_notch_count = 1 set dyn_notch_q = 500 set acc_calibration = -94,18,-73,1 set serialrx_provider = CRSF set min_throttle = 1070 set dshot_bidir = ON set use_unsynced_pwm = OFF set motor_pwm_protocol = DSHOT600 set motor_pwm_rate = 480 set motor_poles = 12 set failsafe_procedure = GPS-RESCUE set bat_capacity = 1300 set beeper_dshot_beacon_tone = 3 set yaw_motors_reversed = ON set small_angle = 180 set gps_provider = UBLOX set gps_auto_baud = ON set gps_ublox_use_galileo = ON set gps_rescue_sanity_checks = RESCUE_SANITY_FS_ONLY set gps_rescue_min_sats = 6 set gps_rescue_min_dth = 50 set gps_rescue_allow_arming_without_fix = ON set report_cell_voltage = ON set osd_cap_alarm = 1300 set osd_vbat_pos = 2305 set osd_rssi_pos = 129 set osd_link_quality_pos = 2209 set osd_rssi_dbm_pos = 2177 set osd_tim_1_pos = 2401 set osd_tim_2_pos = 2369 set osd_flymode_pos = 2381 set osd_throttle_pos = 2361 set osd_vtx_channel_pos = 2497 set osd_current_pos = 2391 set osd_mah_drawn_pos = 2273 set osd_craft_name_pos = 2081 set osd_gps_speed_pos = 2264 set osd_gps_lon_pos = 2129 set osd_gps_lat_pos = 2097 set osd_gps_sats_pos = 2167 set osd_home_dir_pos = 2190 set osd_home_dist_pos = 2200 set osd_flight_dist_pos = 2232 set osd_compass_bar_pos = 2058 set osd_altitude_pos = 2327 set osd_warnings_pos = 14729 set osd_avg_cell_voltage_pos = 2337 set osd_disarmed_pos = 2411 set osd_esc_tmp_pos = 2465 set osd_flip_arrow_pos = 2113 set osd_core_temp_pos = 2296 set osd_log_status_pos = 2145 set osd_efficiency_pos = 231 set debug_mode = GYRO_SCALED set vtx_band = 3 set vtx_channel = 4 set vtx_power = 4 set vtx_low_power_disarm = ON set vtx_freq = 5645 set name = AOS 5

profile 0

profile 0

set feedforward_averaging = 2_POINT set feedforward_smooth_factor = 45 set feedforward_jitter_factor = 6

profile 1

profile 2

restore original profile selection

profile 0

rateprofile 0

rateprofile 1

rateprofile 2

rateprofile 3

rateprofile 4

rateprofile 5

restore original rateprofile selection

rateprofile 0

save configuration

etracer65 commented 2 years ago

The vtxtable you have set up is wrong. The power levels section is wrong and that's why the power level can't be set. Contact the vtx manufacturer to determine which settings to use.

palgy commented 2 years ago

Hi again., Iload the preset for openVTx Jye Smith. with the preset's without any changes the power is still not saved

RadikalBanal commented 1 year ago

I have the same issue. Did u manage to solve it?

palgy commented 1 year ago

Yes, you need to make sure that you select right setting for the cloud build

On Wed, 26 Jul 2023 at 20:15 Leon @.***> wrote:

I have the same issue. Did u manage to solve it?

— Reply to this email directly, view it on GitHub https://github.com/betaflight/betaflight-configurator/issues/2849#issuecomment-1652207864, or unsubscribe https://github.com/notifications/unsubscribe-auth/ADJMD3GOVEI34ZN27RFFNITXSFGC3ANCNFSM5P54Y7SA . You are receiving this because you authored the thread.Message ID: @.***>

-- Yuval Palomo