I am running Windows 11 Pro and can not get my flight controller to connect using 10.9.0 (697943b). Device Manager registers the Flight Controller as Betaflight STM32F7x2 in COM 3. When I open Configurator 10.9 the port drop down remains stuck at "Loading..," If I run the ImpulseRC Driver Fixer, it puts my FC into DFU mode and 10.9 will then recognize the COM port in the Update Firmware screen. If I unplug the FC and plug it back in to kick it out of DFU, 10.9 no longer sees the port. Strangely, If I uninstall 10.9 and reinstall 10.8 I can connect with no issues.
To Reproduce
Plug flight controller into a PC via USB C running Windows 11 Pro.
Expected behavior
Betaflight Configurator 10.9 Loads the COM port for the connected Flight Controller
Configurator version
10.9.0 (697943b)
Flight controller configuration
# version
# Betaflight / STM32F7X2 (S7X2) 4.3.0 Apr 15 2022 / 10:17:24 (9360ab1) MSP API: 1.44
# config: manufacturer_id: TMTR, board_name: TMPACERF7, version: c2b8c0d3, date: 2021-06-18T03:42:42Z
# start the command batch
batch start
board_name TMPACERF7
manufacturer_id TMTR
# name: Xing
# feature
feature -RX_PARALLEL_PWM
feature RX_SERIAL
feature TELEMETRY
# serial
serial 0 64 115200 57600 0 115200
serial 2 1 115200 57600 0 115200
# beeper
beeper -GYRO_CALIBRATED
beeper -RX_LOST_LANDING
beeper -ARMING_GPS_FIX
beeper -BAT_LOW
beeper -GPS_STATUS
beeper -ACC_CALIBRATION
beeper -ACC_CALIBRATION_FAIL
beeper -READY_BEEP
beeper -DISARM_REPEAT
beeper -ARMED
beeper -SYSTEM_INIT
beeper -ON_USB
beeper -BLACKBOX_ERASE
beeper -CRASH_FLIP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSE
beeper -RC_SMOOTHING_INIT_FAIL
# beacon
beacon RX_LOST
beacon RX_SET
# aux
aux 0 0 4 1825 2100 0 0
aux 1 1 0 1400 2100 0 0
aux 2 13 3 1850 2100 0 0
aux 3 35 2 1850 2100 0 0
aux 4 36 5 1775 2100 0 0
# rxrange
rxrange 0 988 2011
rxrange 1 988 2011
rxrange 2 988 2011
rxrange 3 988 2011
# master
set gyro_lpf1_static_hz = 0
set gyro_lpf2_static_hz = 600
set dyn_notch_count = 2
set dyn_notch_q = 400
set dyn_notch_min_hz = 90
set dyn_notch_max_hz = 800
set gyro_lpf1_dyn_min_hz = 0
set gyro_lpf1_dyn_max_hz = 0
set acc_calibration = -39,-42,-117,1
set mag_hardware = NONE
set baro_hardware = NONE
set mid_rc = 1501
set min_check = 1020
set rc_smoothing_auto_factor = 45
set rc_smoothing_auto_factor_throttle = 45
set serialrx_provider = CRSF
set min_throttle = 1070
set dshot_bidir = ON
set use_unsynced_pwm = OFF
set motor_pwm_protocol = DSHOT600
set motor_pwm_rate = 480
set bat_capacity = 1250
set yaw_motors_reversed = ON
set small_angle = 180
set deadband = 4
set simplified_gyro_filter_multiplier = 120
set osd_cap_alarm = 1000
set osd_alt_alarm = 400
set osd_rssi_pos = 6167
set osd_tim_2_pos = 266
set osd_remaining_time_estimate_pos = 299
set osd_current_pos = 6230
set osd_mah_drawn_pos = 6198
set osd_gps_speed_pos = 100
set osd_gps_lon_pos = 67
set osd_gps_lat_pos = 35
set osd_gps_sats_pos = 4
set osd_home_dir_pos = 9
set osd_home_dist_pos = 12
set osd_flight_dist_pos = 79
set osd_compass_bar_pos = 41
set osd_altitude_pos = 131
set osd_warnings_pos = 6569
set osd_avg_cell_voltage_pos = 6158
set osd_battery_usage_pos = 40
set osd_disarmed_pos = 6539
set osd_nvario_pos = 164
set osd_rtc_date_time_pos = 8
set rate_6pos_switch = ON
set rpm_filter_q = 1000
set rpm_filter_fade_range_hz = 100
set name = Xing
profile 0
# profile 0
set dterm_lpf1_dyn_min_hz = 0
set dterm_lpf1_dyn_max_hz = 0
set dterm_lpf1_dyn_expo = 0
set dterm_lpf1_static_hz = 105
set dterm_lpf2_static_hz = 210
set anti_gravity_gain = 5000
set p_pitch = 59
set i_pitch = 90
set d_pitch = 33
set f_pitch = 137
set p_roll = 54
set i_roll = 82
set d_roll = 29
set f_roll = 125
set p_yaw = 54
set i_yaw = 82
set f_yaw = 125
set d_min_roll = 29
set d_min_pitch = 33
set feedforward_averaging = 2_POINT
set feedforward_smooth_factor = 35
set feedforward_jitter_factor = 4
set feedforward_boost = 18
set simplified_master_multiplier = 110
set simplified_i_gain = 85
set simplified_d_gain = 90
set simplified_pi_gain = 110
set simplified_dmax_gain = 0
set simplified_feedforward_gain = 95
set simplified_pitch_pi_gain = 105
set simplified_dterm_filter_multiplier = 140
rateprofile 0
# rateprofile 0
set roll_rc_rate = 2
set pitch_rc_rate = 2
set yaw_rc_rate = 2
set roll_expo = 40
set pitch_expo = 40
set yaw_expo = 40
set roll_srate = 80
set pitch_srate = 80
set yaw_srate = 60
# end the command batch
batch end
Add any other context about the problem that you think might be relevant here
haslinghuis
commented
1 year ago
Describe the bug
I am running Windows 11 Pro and can not get my flight controller to connect using 10.9.0 (697943b). Device Manager registers the Flight Controller as Betaflight STM32F7x2 in COM 3. When I open Configurator 10.9 the port drop down remains stuck at "Loading..," If I run the ImpulseRC Driver Fixer, it puts my FC into DFU mode and 10.9 will then recognize the COM port in the Update Firmware screen. If I unplug the FC and plug it back in to kick it out of DFU, 10.9 no longer sees the port. Strangely, If I uninstall 10.9 and reinstall 10.8 I can connect with no issues.
To Reproduce
Plug flight controller into a PC via USB C running Windows 11 Pro.
Expected behavior
Betaflight Configurator 10.9 Loads the COM port for the connected Flight Controller
Configurator version
10.9.0 (697943b)
Flight controller configuration
Add any other context about the problem that you think might be relevant here
No response