search

bigtreetech / BIGTREETECH-SKR-V1.3

32bit board with LPC1768, support marlin2.0 and smoothieware, support lcd2004/12864, On-board TMC2130 SPI interface and TMC2208 UART interface no additional wiring is required
1.01k stars 1.15k forks source link

BTT TMC2130SPI V3 #215

Open FacusFPV opened 4 years ago

FacusFPV commented 4 years ago

good morning

I have a skr1.3 working with tmc2208 uart. I bought some btt tmc2130 spi v3 but I can't make the engines move.

TMC2130 V3.0 SPI Mode https://www.aliexpress.com/item/32970150483.html?spm=a2g0s.9042311.0.0.56744c4diNkGvn

SW SPI enabled CFG 4 and CFG 5 to gnd Spi without resitor

SENT: M122 READ: X Y Z E READ: Enabled false false false false READ: Set current 750 800 850 850 READ: RMS current 1325 1436 1491 826 READ: MAX current 1868 2025 2102 1165 READ: Run current 23/31 25/31 26/31 26/31 READ: Hold current 11/31 12/31 13/31 13/31 READ: CS actual 0/31 0/31 0/31 13/31 READ: PWM scale 0 0 0 15 READ: vsense 0=.325 0=.325 0=.325 1=.18 READ: stealthChop false false false true READ: msteps 256 256 256 16 READ: tstep 0 0 0 max READ: pwm READ: threshold
READ: [mm/s]
READ: OT prewarn false false false false READ: OT prewarn has READ: been triggered false false false false READ: off time 0 0 0 3 READ: blank time 16 16 16 24 READ: hysteresis READ: -end -3 -3 -3 -1 READ: -start 1 1 1 1 READ: Stallguard thrs 0 0 0
READ: DRVSTATUS X Y Z E READ: stallguard
READ: sg_result 0 0 0
READ: fsactive
READ: stst * READ: olb
READ: ola
READ: s2gb
READ: s2ga
READ: otpw
READ: ot
READ: 157C
READ: 150C
READ: 143C
READ: 120C
READ: s2vsa
READ: s2vsb
READ: Driver registers: READ: X 0x00:00:00:00 Bad response! READ: Y 0x00:00:00:00 Bad response! READ: Z 0x00:00:00:00 Bad response! READ: E 0xC0:0D:00:00 READ: READ: READ: Testing X connection... Error: All LOW (TMC2130 SPI V3) READ: Testing Y connection... Error: All LOW (TMC2130 SPI V3) READ: Testing Z connection... Error: All LOW (TMC2130 SPI V3) READ: Testing E connection... OK (TMC2208 UART v3)

Talha909 commented 4 years ago

Have you give the power to the board. When you only power from the usb then its not work

FacusFPV commented 4 years ago

the printer has a 12v source connected

XzenHD commented 4 years ago

I have the same problem. Printer is connected to 12v power-source, with the jumper in the right possition on the motherboard. I have stopped trying with the BTT stepper-drivers after having tried 8 different peaces

Talha909 commented 4 years ago

I have the same problem. Printer is connected to 12v power-source, with the jumper in the right possition on the motherboard. I have stopped trying with the BTT stepper-drivers after having tried 8 different peaces

which tmc do you have? Please paste the config files

Talha909 commented 4 years ago

the printer has a 12v source connected

only one tmc is ok other 3 are not. Please past the pic and config files.