search

bigtreetech / BIGTREETECH-SKR-mini-E3

BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
2.01k stars 1.97k forks source link

USB Drivers Windows 10 #35

Open glenmorangie007 opened 5 years ago

glenmorangie007 commented 5 years ago

He all

I can't get the MAPLE USB Drivers to install under Windows 10 - I am running Windows 10 Pro 64 bit and every time U try to install the drivers for MAPLE it displays "The Third-Party inf does not contain digital signature information" so the drivers won't install - when launching Cura 4.3 the printer control panel hangs and I have to disconnect the printer, switch it off and start it up again without the USB cable inserted. Any advice please so I can print to the SKR MINI E3 V1.2 via Cura

Thanks

ManiRX100 commented 5 years ago

I also use Windows 10. But the OS recognized the device and showed that the drivers are already up to date. In your case you may try disabling the "DIGITAL SIGNATURE CHECKING" in the start up settings.

glenmorangie007 commented 5 years ago

I have done all that but whenever I connect the Ender 3 to be used in Cura - The Ender 3 locks up and has to be restarted without the USB Cable attached - the only way I can print is slicing the file first then uploading that to the TF card and printing from the TF card

ManiRX100 commented 5 years ago

I had this issue first when I connected through the USB. The buzzer started and the printer just froze. I had to reset the printer again. I am not sure exactly whether this is the solution or it is related to it. I feel that the board has some power grounding issues. Are you using the stock two pin power chord? I changed it to a three pin power chord which has an "earth" pin and it solved the issue for me.

ManiRX100 commented 5 years ago

I have done all that but whenever I connect the Ender 3 to be used in Cura - The Ender 3 locks up and has to be restarted without the USB Cable attached - the only way I can print is slicing the file first then uploading that to the TF card and printing from the TF card

@glenmorangie007 I got the issue again when I tried using the USB connection in Cura. My buzzer starts beeping and printer freezes. But the printer works in USB when I use Pronterface. I tried this you tube video "How to fix Cura or Slicer Not CONNECTING to 3D Printer Creality Ender 3?", but in vain.

ManiRX100 commented 5 years ago

https://github.com/Ultimaker/Cura/issues/4196.. Some solutions are here.

glenmorangie007 commented 5 years ago

@ManiRX100 another email has gone off to BigTree about this issue - probably take a couple of days to resolve again ! Same for me - I can connect to the printer using Pronterface fine !

ManiRX100 commented 5 years ago

@glenmorangie007 May be the issue is the Cura compatibility with the latest firmware. Meanwhile let us try the solutions in the older thread I mentioned. Are you aware of compiling this BTT V1.2 board in Arduino IDE? I am not getting any responses to that thread.

glenmorangie007 commented 5 years ago

@ManiRX100 Everything I have seen shows the only way to compile this is with VS not with Arduino IDE as VS pulls down the necessary dependencies it needs to sort it out

ManiRX100 commented 5 years ago

A new firmware was released today. But it throws error. Has anyone tried it? Does it solve the issue with the Cura ?

glenmorangie007 commented 5 years ago

@ManiRX100 Haven't tried it yet - my firmware is working at the moment apart from the USB issue in Cura ! - I'm waiting for Bigtree to come back to me - I followed their instructions and re-installed the correct MAPLE USB Driver but it still fails each time, but Pronterface works fine - I want Cura to work so I don't have to keep slicing and sending the GCODE to a TF card all the time

ManiRX100 commented 5 years ago

@glenmorangie007 Please let me know once they get back. Thanks.

glenmorangie007 commented 5 years ago

@ManiRX100 Have you tried the new version of the firmware ? Does it now work with Cura ??

ManiRX100 commented 5 years ago

@glenmorangie007 I was able to compile the new firmware. but still the issue with Cura exists. It works in Pronterface. I wonder what is the issue.

maddingamer commented 4 years ago

looks similar to #40

Herb01 commented 4 years ago

I just installed the SKR MINI E3 V2 and now trying to install the usb driver with Win10. I can't install the Maple driver. Every time it complains about unknown USB device. Windows complains about unsigned driver so i disable this check. No luck. I'm running out of options. What to do

danlavu commented 4 years ago

I was able to install the drivers by rebooting into unsigned mode, hold shift while clicking reboot and go-to troubleshooting in the recovery menu, you can boot windows permitting unsigned driver installation. However the device still shows up as an unknown device but the drivers are installed.