search

bigtreetech / BIGTREETECH-SKR-mini-E3

BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
2.02k stars 1.98k forks source link

[REQ] Publish configuration.h/configuration_adv.h for Ender 5 SKR-mini-E3-V3.0 #605

Open jnko opened 2 years ago

jnko commented 2 years ago

Could you kindly publish the configuration.h/configuration_adv.h for Ender 5 which was used to build the binaries for SKR-mini-E3-V3.0? All you released are the ones for Ender 3

Thanks in advance

Digolera commented 2 years ago

https://youtu.be/ugRHsLWH95A

this .bin works to me, but still want a configuration.h :(

Seelenkind commented 2 years ago

pls try this. NO BL Touch. if you need BL Touch give feedback Ender 5 Marlin 2.0.9.3 SKR Mini E3 V3 NO BL TOUCH.zip

rhweese commented 1 year ago

I also have the Ender 5 (2019) model, I installed the SKR Mini V3 V2.0. After compiling the firmware from github for this setup and flashing the firmware to the printer, I get no movement out any of the stepper motors. The X,Y,Z or E stepper motors show no sign of movement at all, where they were working fine before. The end stop switches are new, all wiring is new, no BL touch_or other add on's. The firmware from Github for the Ender5 with the SKR Mini V3 V2.0. should work without modifications I would assume. At any rate I made no changes. I have tried trouble shooting this for a week and I'm at a total dead end here, If and one has any ideas as to what might be the hang up I would like to hear from you, I could really use some ones help at this point. I am using this file from github if anyone is interested in taking a look, here. (https://github.com/alepee/Marlin-Ender-5) I have tested all hardware and electrical connections just to be sure, but as stated before they were working fine before this happened, so I thing it has to be a firmware issue. I do not know if the steppers motors have been disabled in this firmware or not and if so how could it work for the Ender 5 which is of a box type configuration anyway, what would be the reason for doing that in the first place. I really could use some help on this one. I've reach a dead end as where to next. Any ideas would help!!!! [Thanks!!!!

rhweese commented 1 year ago

Hello JNKO! here is the configuration.h/configuration_adv.h files, This files are for the Ender 5. Both files are in the zip file folder. Let me know if you need anything else.. I will give you the complete Ender 5 file set I am using now, I have had to work out a lot of problems with it to get it to work with by ender 5 sense my ender 5 is the old 2019 box type (see photo below). The printer files using this config set work great so I hope they are what you are looking for. Let me know if I can be any more help! Configuration.zip Screenshot_20221229_100536 Thanks JNKO sorry it took a while to get back, I was still debuging.

rhweese commented 1 year ago

HELLO SEELENKIND! Thanks for your help, I did go and find a firmware which was in the BIGTREETECK-SKR-mini-E3-master ,V2.0. I found that it was close but I needed to make many changes for it to work for the Ender 5 even though it said it was for the ender 5, i.e. x,y,z, were reversed, print size was off and so on, and more. But you sent me in the right direction to find the files I needed which was a great help so I wanted to say thank you.