Closed Silverender closed 3 years ago
If I'm not mistaken, you should be fine serial port -1 therefore
Hello radek, When i tried -1 i can't compile, already tried shows error
El vie., 29 ene. 2021 21:29, Radek notifications@github.com escribió:
If I'm not mistaken, you should be fine serial port -1 therefore
define SERIAL_PORT -1
— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/1578#issuecomment-770032734, or unsubscribe https://github.com/notifications/unsubscribe-auth/ASUSVI2H5OR43ZJOOAUB2P3S4MLB7ANCNFSM4WYKUHOA .
Pardon, 0 was correct But nothing must be connected to the MKS USB port at the same time
Uncomment
Will try, regarding usb port just and extension is connected i actually have to unplug screen to flash or connect thru usb or computer is unable to connect
El vie., 29 ene. 2021 21:47, Radek notifications@github.com escribió:
Uncomment
define M114_DETAIL
define REPORT_FAN_CHANGE
— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/1578#issuecomment-770041242, or unsubscribe https://github.com/notifications/unsubscribe-auth/ASUSVI5ZODY5LS5WHBFZFRLS4MNGLANCNFSM4WYKUHOA .
A USB port and a TFT port shared by the same pins can only be connected by one of them at a time
Thanks, will try activating those lines and keep you posted about results
El vie., 29 ene. 2021 21:59, Radek notifications@github.com escribió:
A USB port and a TFT port shared by the same port can only be connected by one of them at a time
— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/1578#issuecomment-770046658, or unsubscribe https://github.com/notifications/unsubscribe-auth/ASUSVI7YHBOH7BYGFGUPAC3S4MORXANCNFSM4WYKUHOA .
Any news?
Nothing, doesn't work, #define M114_DETAIL & #define REPORT_FAN_CHANGE activated but still No printer attached is shown on the screen
I tested MKS_Gen_L_V1.0 (latest bugfix2.0.x) with BT_TFT3.5_V3.0 (latest master) and it is OK. The TFT was attached to the AUX1 connector, USB not connected. I attach the config files I used for Marlin. Configurations.zip
I tested MKS_Gen_L_V1.0 (latest bugfix2.0.x) with BT_TFT3.5_V3.0 (latest master) and it is OK. The TFT was attached to the AUX1 connector, USB not connected. I attach the config files I used for Marlin. Configurations.zip
Thanks kisslorand will try, could you post me also your screen firmware?
I tested MKS_Gen_L_V1.0 (latest bugfix2.0.x) with BT_TFT3.5_V3.0 (latest master) and it is OK. The TFT was attached to the AUX1 connector, USB not connected. I attach the config files I used for Marlin. Configurations.zip
I see your machine is not an Ender 3, and also surprises me that in your CONFIG line "REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER" necessary for the screen is commented :-/
It's not a machine, just an MKS GenL v1.0 motherboard and a BTT TFT35 v3.0 connected together for testing your problem.
nothing, already ordered a BTT SKR 1.4 Turbo, but will keep trying to fix it.
Please help the community and close the ticket once you do not need it anymore. Thank you
Oldman4U it would be nice if you were as concerned about solving problems as you are about closing out posts. Part of the reason for posts is because more than one person might have the same issue and instead of having to resolve the issue with the community, people can better help each other with problems that haven't been solved. Why are you so concerned about open posts? Obviously this is still an issue for people.
Hi.
Two reasons
First. To keep the ticket system here usable.
Second. This is about improving BTT firmware and not a user group. There are other places (which are mentioned when you start a ticket) to share user related problems.
Thank you for your understanding
joemama626 notifications@github.com schrieb am Mo. 1. März 2021 um 01:14:
Oldman4U it would be nice if you were as concerned about solving problems as you are about closing out posts. Part of the reason for posts is because more than one person might have the same issue and instead of having to resolve the issue with the community, people can better help each other with problems that haven't been solved. Why are you so concerned about open posts? Obviously this is still an issue for people.
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/1578#issuecomment-787553472, or unsubscribe https://github.com/notifications/unsubscribe-auth/AM6XKZELQO4HHTDKLQCNPHTTBLL4VANCNFSM4WYKUHOA .
And in this particular case it is double wrong because it is not TFT firmware related and the problem is most likely MKS related. So the MKS forum would be the right place.
Georg Deisting georgdeisting@gmail.com schrieb am Mo. 1. März 2021 um 06:27:
Hi.
Two reasons
First. To keep the ticket system here usable.
Second. This is about improving BTT firmware and not a user group. There are other places (which are mentioned when you start a ticket) to share user related problems.
Thank you for your understanding
joemama626 notifications@github.com schrieb am Mo. 1. März 2021 um 01:14:
Oldman4U it would be nice if you were as concerned about solving problems as you are about closing out posts. Part of the reason for posts is because more than one person might have the same issue and instead of having to resolve the issue with the community, people can better help each other with problems that haven't been solved. Why are you so concerned about open posts? Obviously this is still an issue for people.
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/1578#issuecomment-787553472, or unsubscribe https://github.com/notifications/unsubscribe-auth/AM6XKZELQO4HHTDKLQCNPHTTBLL4VANCNFSM4WYKUHOA .
Hello I'm sorry, I'm new here
I had the same problem, the display did not connect to the SKR1.4 Turbo
It was enough to change the value of the Serial port in the Config file in the oro display firmware directory (valid for TFT35 V3)
In VisualStudioCode is coment
Of course, the baud rate of the printer and the display must also be set to the same value
Maybe I helped
Had to replace motherboard and screen, now working perfectly with skr 1.4 turbo and a new tft35 3.0
El mar., 13 abr. 2021 16:44, VikyTT @.***> escribió:
Hello I'm sorry, I'm new here
I had the same problem, the display did not connect to the SKR1.4 Turbo
It was enough to change the value of the Serial port in the Config file in the oro display firmware directory (valid for TFT35 V3)
In VisualStudioCode is coment Serial Always ON Keep UART (serial communication) alive in Marlin Mode. Allows seamless OctoPrint UART connection to the TFT's UART/serial expansion port no matter which mode the TFT is in. Options: [enable: 1, disable: 0]
serial_always_on:1
Of course, the baud rate of the printer and the display must also be set to the same value
Maybe I helped
— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/1578#issuecomment-818793141, or unsubscribe https://github.com/notifications/unsubscribe-auth/ASUSVIZWBLYRDLHAILMNDT3TIRKELANCNFSM4WYKUHOA .
Please help the community and close the ticket once you do not need it anymore. Thank you
@Msq001
This ticket is MKS mainboard related and finally has been solved by replacing the MKS with a SKR board. Please close it.
Thank you
This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs.
Hello,
printer was working perfectly with Marlin 1.1.9 and firmware 3.0.25 on the screen but after updating screen to 3.0.26 I totally lost connection between printer and screen, "No printer Attached" message is always shown.
After that I decided to update Marlin to 2.0.7.2 but still doesn't work, connection is just done by 4 cables RS232 for touch mode only, "REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER" is activated in Configuration.h and "CR10_STOCKDISPLAY" Deactivated. Baudrate on screen and marlin is the same (250000) also tried 115200 and didn't work either.
Recompiled BTT TFT35 firmware from last master many times to avoid prebuilded releases but still doesn't work
This is really driving me crazy, any clue? All was working until screen update. Also tried to go back to 1.1.9 but doesn't work either.
Printer: Ender 3 Motherboard: MKS GEN L 1.0 Marlin: 2.0.7.2 Screen: BTT TFT35 3.0 - v.3.0.26 firmware. Connection thru RS232 only
Marlin.Configuration.zip TFT35.Configuration.zip