search

billw2 / rpi-clone

A shell script to clone a booted disk.
BSD 3-Clause "New" or "Revised" License
2.52k stars 331 forks source link

Failed to clone raspbian 16Gb SD card #67

Open Geronimo2015 opened 5 years ago

Geronimo2015 commented 5 years ago

Hello,

I tried to clone a SD card with Raspian on to to a fresh 128Gb SSD drive but it failed. Any ideas?

pi@homeassistant:~/src/rpi-clone $ sudo rpi-clone sda -f

Booted disk: mmcblk0 15.9GB                Destination disk: sda 128.0GB
---------------------------------------------------------------------------
Part      Size    FS     Label           Part   Size    FS     Label
1         66.0MB  fat16  --              1      66.0MB  fat16  --
2         15.9GB  EXT    --              2      15.9GB  EXT    --

5         33.3MB  ext4   SETTINGS        5      33.3MB  ext4   SETTINGS
6 /boot   72.2MB  fat32  --              6      72.2MB  fat32  --
7 root    15.8GB  ext4   root            7      15.8GB  ext4   root
---------------------------------------------------------------------------
== Initialize: IMAGE mmcblk0 partition table to sda - forced by option ==
1                                    : IMAGE     to sda1
5                                    : IMAGE     to sda5
6 /boot               (23.0MB used)  : MKFS SYNC to sda6
7 root                (9.4GB used)   : RESIZE(127.9GB) MKFS SYNC to sda7
---------------------------------------------------------------------------
Run setup script       : no
Verbose mode           : no
-----------------------:
** WARNING **          : All destination disk sda data will be overwritten!
                       :   The partition structure will be imaged from mmcblk0.
-----------------------:

-------> /tmp/rpi-clone-output

Checking that no-one is using this disk right now ... OK

Disk /dev/sda: 119.2 GiB, 128035674112 bytes, 250069676 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xe1ff21ed

Old situation:

Device     Boot  Start      End  Sectors  Size Id Type
/dev/sda1         8192   137215   129024   63M  e W95 FAT16 (LBA)
/dev/sda2       137216 31116287 30979072 14.8G  5 Extended
/dev/sda5       139264   204797    65534   32M 83 Linux
/dev/sda6       204800   346111   141312   69M  c W95 FAT32 (LBA)
/dev/sda7       352256 31116287 30764032 14.7G 83 Linux

>>> Script header accepted.
>>> Script header accepted.
>>> Script header accepted.
>>> Script header accepted.
>>> Created a new DOS disklabel with disk identifier 0x194d70ba.
/dev/sda1: Created a new partition 1 of type 'W95 FAT16 (LBA)' and of size 63 MiB.
Partition #1 contains a vfat signature.
/dev/sda2: Created a new partition 2 of type 'Extended' and of size 119.2 GiB.
/dev/sda3: Created a new partition 5 of type 'Linux' and of size 32 MiB.
Partition #5 contains a ext4 signature.
/dev/sda6: Start sector 204800 out of range.
Failed to add #6 partition: Numerical result out of range
Leaving.

====rpi-clone
==orig:
label: dos
label-id: 0xe1ff21ed
device: /dev/mmcblk0
unit: sectors

/dev/mmcblk0p1 : start=        8192, size=      129024, type=e
/dev/mmcblk0p2 : start=      137216, size=    30979072, type=5
/dev/mmcblk0p5 : start=      139264, size=       65534, type=83
/dev/mmcblk0p6 : start=      204800, size=      141312, type=c
/dev/mmcblk0p7 : start=      352256, size=    30764032, type=83

==edited:
label: dos
label-id: 0xe1ff21ed
device: /dev/mmcblk0
unit: sectors

/dev/mmcblk0p1 : start=        8192, size=      129024, type=e
/dev/mmcblk0p2 : start=      137216,  type=5
/dev/mmcblk0p5 : start=      139264, size=       65534, type=83
/dev/mmcblk0p6 : start=      204800, size=      141312, type=c
/dev/mmcblk0p7 : start=      352256,  type=83
ArmandBENETEAU commented 4 years ago

I have the same problem on my 64 GB SSD, is there any update about a solution?